| Message ID | 1460710374-25077-1-git-send-email-appanad@xilinx.com (mailing list archive) |
|---|---|
| State | Changes Requested |
| Headers | show |
On Fri, Apr 15, 2016 at 02:22:53PM +0530, Kedareswara rao Appana wrote: > Device-tree binding documentation for Xilinx zynqmp dma engine used in > Zynq UltraScale+ MPSoC. > > Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com> > Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com> > --- > Changes in v6: > - Removed desc-axi-cache/dst-axi-cache/src-axi-cache properties > from the binding doc as it allow broken combinations when dma-coherent > is set as suggested by Rob. > - Fixed minor comments given by Rob related coding(lower case DT node name). > Changes in v5: > - Use dma-coherent flag for coherent transfers as suggested by rob. > - Removed unnecessary properties from binding doc as suggested by Rob. > Changes in v4: > - None > Changes in v3: > - None > Changes in v2: > - None. > > .../devicetree/bindings/dma/xilinx/zynqmp_dma.txt | 44 ++++++++++++++++++++++ > 1 file changed, 44 insertions(+) > create mode 100644 Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt > > diff --git a/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt > new file mode 100644 > index 0000000..f0f0b54 > --- /dev/null > +++ b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt > @@ -0,0 +1,44 @@ > +Xilinx ZynqMP DMA engine, it does support memory to memory transfers, > +memory to device and device to memory transfers. It also has flow > +control and rate control support for slave/peripheral dma access. > + > +Required properties: > +- compatible : Should be "xlnx,zynqmp-dma-1.0" > +- reg : Memory map for gdma/adma module access. > +- interrupt-parent : Interrupt controller the interrupt is routed through > +- interrupts : Should contain DMA channel interrupt. > +- xlnx,bus-width : Axi buswidth in bits. Should contain 128 or 64 I think how this is getting used by the driver is wrong. {src,dst}_addr_widths are supposed to be a bitmask of supported slave device register widths. You aren't doing a bitmask and you are also saying you only support slaves with 8 or 16 byte data registers which is somewhat rare. It may happen to work because 128/8 == BIT(4). However, the documentation for the field is contradictory in that it says 1,2,4 or 8 byte widths are supported, but the enum has more sizes. Rob -- To unsubscribe from this list: send the line "unsubscribe dmaengine" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Rob, Thanks for the review... > -----Original Message----- > From: Rob Herring [mailto:robh@kernel.org] > Sent: Thursday, April 21, 2016 7:12 PM > To: Appana Durga Kedareswara Rao <appanad@xilinx.com> > Cc: pawel.moll@arm.com; mark.rutland@arm.com; > ijc+devicetree@hellion.org.uk; galak@codeaurora.org; Michal Simek > <michals@xilinx.com>; Soren Brinkmann <sorenb@xilinx.com>; > vinod.koul@intel.com; dan.j.williams@intel.com; Appana Durga Kedareswara > Rao <appanad@xilinx.com>; moritz.fischer@ettus.com; > laurent.pinchart@ideasonboard.com; luis@debethencourt.com; Anirudha > Sarangi <anirudh@xilinx.com>; Punnaiah Choudary Kalluri > <punnaia@xilinx.com>; devicetree@vger.kernel.org; linux-arm- > kernel@lists.infradead.org; linux-kernel@vger.kernel.org; > dmaengine@vger.kernel.org > Subject: Re: [PATCH v6 1/2] Documentation: DT: dma: Add Xilinx zynqmp dma > device tree binding documentation > > On Fri, Apr 15, 2016 at 02:22:53PM +0530, Kedareswara rao Appana wrote: > > Device-tree binding documentation for Xilinx zynqmp dma engine used in > > Zynq UltraScale+ MPSoC. > > > > Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com> > > Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com> > > --- > > Changes in v6: > > - Removed desc-axi-cache/dst-axi-cache/src-axi-cache properties > > from the binding doc as it allow broken combinations when dma-coherent > > is set as suggested by Rob. > > - Fixed minor comments given by Rob related coding(lower case DT node > name). > > Changes in v5: > > - Use dma-coherent flag for coherent transfers as suggested by rob. > > - Removed unnecessary properties from binding doc as suggested by Rob. > > Changes in v4: > > - None > > Changes in v3: > > - None > > Changes in v2: > > - None. > > > > .../devicetree/bindings/dma/xilinx/zynqmp_dma.txt | 44 > ++++++++++++++++++++++ > > 1 file changed, 44 insertions(+) > > create mode 100644 > Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt > > > > diff --git a/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt > b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt > > new file mode 100644 > > index 0000000..f0f0b54 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt > > @@ -0,0 +1,44 @@ > > +Xilinx ZynqMP DMA engine, it does support memory to memory transfers, > > +memory to device and device to memory transfers. It also has flow > > +control and rate control support for slave/peripheral dma access. > > + > > +Required properties: > > +- compatible : Should be "xlnx,zynqmp-dma-1.0" > > +- reg : Memory map for gdma/adma module access. > > +- interrupt-parent : Interrupt controller the interrupt is routed through > > +- interrupts : Should contain DMA channel interrupt. > > +- xlnx,bus-width : Axi buswidth in bits. Should contain 128 or 64 > > I think how this is getting used by the driver is wrong. > {src,dst}_addr_widths are supposed to be a bitmask of supported slave > device register widths. You aren't doing a bitmask and you are also > saying you only support slaves with 8 or 16 byte data registers which is > somewhat rare. It may happen to work because 128/8 == BIT(4). However, > the documentation for the field is contradictory in that it says 1,2,4 > or 8 byte widths are supported, but the enum has more sizes. The DMA supports an AXI bus width of 128/64 bits only. Please refer IP data sheet. http://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf Page No: 359(DMA Over fetch section). That's why during probe we are making the dma_device supported source and destination address widths accordingly based on the DT property. Snap shot of driver code from the probe: struct dma_device *p; p->dst_addr_widths = zdev->chan->bus_width / 8; p->src_addr_widths = zdev->chan->bus_width / 8; Where bus_width property is read from the probe. err = of_property_read_u32(node, "xlnx,bus-width", &chan->bus_width) Cheers!, Kedar... > > Rob -- To unsubscribe from this list: send the line "unsubscribe dmaengine" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Apr 22, 2016 at 12:36 AM, Appana Durga Kedareswara Rao <appana.durga.rao@xilinx.com> wrote: > Hi Rob, > > Thanks for the review... > >> -----Original Message----- >> From: Rob Herring [mailto:robh@kernel.org] >> Sent: Thursday, April 21, 2016 7:12 PM >> To: Appana Durga Kedareswara Rao <appanad@xilinx.com> >> Cc: pawel.moll@arm.com; mark.rutland@arm.com; >> ijc+devicetree@hellion.org.uk; galak@codeaurora.org; Michal Simek >> <michals@xilinx.com>; Soren Brinkmann <sorenb@xilinx.com>; >> vinod.koul@intel.com; dan.j.williams@intel.com; Appana Durga Kedareswara >> Rao <appanad@xilinx.com>; moritz.fischer@ettus.com; >> laurent.pinchart@ideasonboard.com; luis@debethencourt.com; Anirudha >> Sarangi <anirudh@xilinx.com>; Punnaiah Choudary Kalluri >> <punnaia@xilinx.com>; devicetree@vger.kernel.org; linux-arm- >> kernel@lists.infradead.org; linux-kernel@vger.kernel.org; >> dmaengine@vger.kernel.org >> Subject: Re: [PATCH v6 1/2] Documentation: DT: dma: Add Xilinx zynqmp dma >> device tree binding documentation >> >> On Fri, Apr 15, 2016 at 02:22:53PM +0530, Kedareswara rao Appana wrote: >> > Device-tree binding documentation for Xilinx zynqmp dma engine used in >> > Zynq UltraScale+ MPSoC. >> > >> > Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com> >> > Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com> >> > --- >> > Changes in v6: >> > - Removed desc-axi-cache/dst-axi-cache/src-axi-cache properties >> > from the binding doc as it allow broken combinations when dma-coherent >> > is set as suggested by Rob. >> > - Fixed minor comments given by Rob related coding(lower case DT node >> name). >> > Changes in v5: >> > - Use dma-coherent flag for coherent transfers as suggested by rob. >> > - Removed unnecessary properties from binding doc as suggested by Rob. >> > Changes in v4: >> > - None >> > Changes in v3: >> > - None >> > Changes in v2: >> > - None. >> > >> > .../devicetree/bindings/dma/xilinx/zynqmp_dma.txt | 44 >> ++++++++++++++++++++++ >> > 1 file changed, 44 insertions(+) >> > create mode 100644 >> Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt >> > >> > diff --git a/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt >> b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt >> > new file mode 100644 >> > index 0000000..f0f0b54 >> > --- /dev/null >> > +++ b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt >> > @@ -0,0 +1,44 @@ >> > +Xilinx ZynqMP DMA engine, it does support memory to memory transfers, >> > +memory to device and device to memory transfers. It also has flow >> > +control and rate control support for slave/peripheral dma access. >> > + >> > +Required properties: >> > +- compatible : Should be "xlnx,zynqmp-dma-1.0" >> > +- reg : Memory map for gdma/adma module access. >> > +- interrupt-parent : Interrupt controller the interrupt is routed through >> > +- interrupts : Should contain DMA channel interrupt. >> > +- xlnx,bus-width : Axi buswidth in bits. Should contain 128 or 64 >> >> I think how this is getting used by the driver is wrong. >> {src,dst}_addr_widths are supposed to be a bitmask of supported slave >> device register widths. You aren't doing a bitmask and you are also >> saying you only support slaves with 8 or 16 byte data registers which is >> somewhat rare. It may happen to work because 128/8 == BIT(4). However, >> the documentation for the field is contradictory in that it says 1,2,4 >> or 8 byte widths are supported, but the enum has more sizes. > > > The DMA supports an AXI bus width of 128/64 bits only. > Please refer IP data sheet. http://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf Page No: 359(DMA Over fetch section). I understand that. That should not really matter if the AXI master properly sets byte lane strobes other than defining max burst length which you already have defined elsewhere. > That's why during probe we are making the dma_device supported source and destination address widths accordingly based on the DT property. > > Snap shot of driver code from the probe: > struct dma_device *p; > p->dst_addr_widths = zdev->chan->bus_width / 8; > p->src_addr_widths = zdev->chan->bus_width / 8; Read what I wrote before and read the documentation for these fields. They are bitmasks. Rob -- To unsubscribe from this list: send the line "unsubscribe dmaengine" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Rob, > -----Original Message----- > From: dmaengine-owner@vger.kernel.org [mailto:dmaengine- > owner@vger.kernel.org] On Behalf Of Rob Herring > Sent: Friday, April 22, 2016 9:43 PM > To: Appana Durga Kedareswara Rao <appanad@xilinx.com> > Cc: pawel.moll@arm.com; mark.rutland@arm.com; > ijc+devicetree@hellion.org.uk; galak@codeaurora.org; Michal Simek > <michals@xilinx.com>; Soren Brinkmann <sorenb@xilinx.com>; > vinod.koul@intel.com; dan.j.williams@intel.com; moritz.fischer@ettus.com; > laurent.pinchart@ideasonboard.com; luis@debethencourt.com; Anirudha > Sarangi <anirudh@xilinx.com>; Punnaiah Choudary Kalluri > <punnaia@xilinx.com>; devicetree@vger.kernel.org; linux-arm- > kernel@lists.infradead.org; linux-kernel@vger.kernel.org; > dmaengine@vger.kernel.org > Subject: Re: [PATCH v6 1/2] Documentation: DT: dma: Add Xilinx zynqmp dma > device tree binding documentation > > On Fri, Apr 22, 2016 at 12:36 AM, Appana Durga Kedareswara Rao > <appana.durga.rao@xilinx.com> wrote: > > Hi Rob, > > > > Thanks for the review... > > > >> -----Original Message----- > >> From: Rob Herring [mailto:robh@kernel.org] > >> Sent: Thursday, April 21, 2016 7:12 PM > >> To: Appana Durga Kedareswara Rao <appanad@xilinx.com> > >> Cc: pawel.moll@arm.com; mark.rutland@arm.com; > >> ijc+devicetree@hellion.org.uk; galak@codeaurora.org; Michal Simek > >> <michals@xilinx.com>; Soren Brinkmann <sorenb@xilinx.com>; > >> vinod.koul@intel.com; dan.j.williams@intel.com; Appana Durga > >> Kedareswara Rao <appanad@xilinx.com>; moritz.fischer@ettus.com; > >> laurent.pinchart@ideasonboard.com; luis@debethencourt.com; Anirudha > >> Sarangi <anirudh@xilinx.com>; Punnaiah Choudary Kalluri > >> <punnaia@xilinx.com>; devicetree@vger.kernel.org; linux-arm- > >> kernel@lists.infradead.org; linux-kernel@vger.kernel.org; > >> dmaengine@vger.kernel.org > >> Subject: Re: [PATCH v6 1/2] Documentation: DT: dma: Add Xilinx zynqmp > >> dma device tree binding documentation > >> > >> On Fri, Apr 15, 2016 at 02:22:53PM +0530, Kedareswara rao Appana wrote: > >> > Device-tree binding documentation for Xilinx zynqmp dma engine used > >> > in Zynq UltraScale+ MPSoC. > >> > > >> > Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com> > >> > Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com> > >> > --- > >> > Changes in v6: > >> > - Removed desc-axi-cache/dst-axi-cache/src-axi-cache properties > >> > from the binding doc as it allow broken combinations when dma-coherent > >> > is set as suggested by Rob. > >> > - Fixed minor comments given by Rob related coding(lower case DT > >> > node > >> name). > >> > Changes in v5: > >> > - Use dma-coherent flag for coherent transfers as suggested by rob. > >> > - Removed unnecessary properties from binding doc as suggested by Rob. > >> > Changes in v4: > >> > - None > >> > Changes in v3: > >> > - None > >> > Changes in v2: > >> > - None. > >> > > >> > .../devicetree/bindings/dma/xilinx/zynqmp_dma.txt | 44 > >> ++++++++++++++++++++++ > >> > 1 file changed, 44 insertions(+) > >> > create mode 100644 > >> Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt > >> > > >> > diff --git > >> > a/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt > >> b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt > >> > new file mode 100644 > >> > index 0000000..f0f0b54 > >> > --- /dev/null > >> > +++ b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt > >> > @@ -0,0 +1,44 @@ > >> > +Xilinx ZynqMP DMA engine, it does support memory to memory > >> > +transfers, memory to device and device to memory transfers. It > >> > +also has flow control and rate control support for slave/peripheral dma > access. > >> > + > >> > +Required properties: > >> > +- compatible : Should be "xlnx,zynqmp-dma-1.0" > >> > +- reg : Memory map for gdma/adma module access. > >> > +- interrupt-parent : Interrupt controller the interrupt is routed through > >> > +- interrupts : Should contain DMA channel interrupt. > >> > +- xlnx,bus-width : Axi buswidth in bits. Should contain 128 or 64 > >> > >> I think how this is getting used by the driver is wrong. > >> {src,dst}_addr_widths are supposed to be a bitmask of supported slave > >> device register widths. You aren't doing a bitmask and you are also > >> saying you only support slaves with 8 or 16 byte data registers which > >> is somewhat rare. It may happen to work because 128/8 == BIT(4). > >> However, the documentation for the field is contradictory in that it > >> says 1,2,4 or 8 byte widths are supported, but the enum has more sizes. > > > > > > The DMA supports an AXI bus width of 128/64 bits only. > > Please refer IP data sheet. > http://www.xilinx.com/support/documentation/user_guides/ug1085-zynq- > ultrascale-trm.pdf Page No: 359(DMA Over fetch section). > > I understand that. That should not really matter if the AXI master properly sets > byte lane strobes other than defining max burst length which you already have > defined elsewhere. > > > That's why during probe we are making the dma_device supported source and > destination address widths accordingly based on the DT property. > > > > Snap shot of driver code from the probe: > > struct dma_device *p; > > p->dst_addr_widths = zdev->chan->bus_width / 8; > > p->src_addr_widths = zdev->chan->bus_width / 8; > > Read what I wrote before and read the documentation for these fields. > They are bitmasks. I misunderstood the question that you asked yesterday. Now I got clarified. Will fix it in the next version of the patch... Thanks for the detailed explanation. Regards, Kedar. > > Rob > -- > To unsubscribe from this list: send the line "unsubscribe dmaengine" in the body > of a message to majordomo@vger.kernel.org More majordomo info at > http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt new file mode 100644 index 0000000..f0f0b54 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt @@ -0,0 +1,44 @@ +Xilinx ZynqMP DMA engine, it does support memory to memory transfers, +memory to device and device to memory transfers. It also has flow +control and rate control support for slave/peripheral dma access. + +Required properties: +- compatible : Should be "xlnx,zynqmp-dma-1.0" +- reg : Memory map for gdma/adma module access. +- interrupt-parent : Interrupt controller the interrupt is routed through +- interrupts : Should contain DMA channel interrupt. +- xlnx,bus-width : Axi buswidth in bits. Should contain 128 or 64 +- clock-names : List of input clocks "clk_main", "clk_apb" + (see clock bindings for details) + +Optional properties: +- xlnx,include-sg : Indicates the controller to operate in simple or + scatter gather dma mode +- xlnx,ratectrl : Scheduling interval in terms of clock cycles for + source AXI transaction +- xlnx,overfetch : Tells whether the channel is allowed to over + fetch the data +- xlnx,src-issue : Number of AXI outstanding transactions on source side +- xlnx,src-burst-len : AXI length for data read. Support only power of + 2 byte values. +- xlnx,dst-burst-len : AXI length for data write. Support only power of + 2 byte values. +- dma-coherent : Present if dma operations are coherent. + +Example: +++++++++ +fpd_dma_chan1: dma@fd500000 { + compatible = "xlnx,zynqmp-dma-1.0"; + reg = <0x0 0xFD500000 0x1000>; + interrupt-parent = <&gic>; + interrupts = <0 117 4>; + clock-names = "clk_main", "clk_apb"; + xlnx,bus-width = <128>; + xlnx,include-sg; + xlnx,overfetch; + dma-coherent; + xlnx,ratectrl = <0>; + xlnx,src-issue = <16>; + xlnx,src-burst-len = <4>; + xlnx,dst-burst-len = <4>; +};