@@ -1,4 +1,108 @@
-Atmel NAND flash
+Atmel NAND flash controller bindings
+
+The NAND flash controller node should be defined under the EBI bus (see
+Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt).
+One or several NAND devices can be defined under this NAND controller.
+The NAND controller might be connected to an ECC engine.
+
+* NAND controller bindings:
+
+Required properties:
+- compatible: should be one of the following
+ "atmel,at91rm9200-nand-controller"
+ "atmel,at91sam9261-nand-controller"
+ "atmel,at91sam9g45-nand-controller"
+ "atmel,sama5d3-nand-controller"
+- ranges: empty ranges property to forward EBI ranges definitions.
+- #address-cells: should be set to 2.
+- #size-cells: should be set to 1.
+- atmel,nfc-io: phandle to the NFC IO block. Only required for sama5d3
+ controllers.
+- atmel,nfc-sram: phandle to the NFC SRAM block. Only required for sama5d3
+ controllers.
+
+Optional properties:
+- ecc-engine: phandle to the PMECC block. Only meaningful if the SoC embeds
+ a PMECC engine.
+
+* NAND device/chip bindings:
+
+Required properties:
+- reg: describes the CS lines assigned to the NAND device. If the NAND device
+ exposes multiple CS lines (multi-dies chips), your reg property will
+ contain X tuples of 3 entries.
+ 1st entry: the CS line this NAND chip is connected to
+ 2nd entry: the base offset of the memory region assigned to this
+ device (always 0)
+ 3rd entry: the memory region size (always 0x800000)
+
+Optional properties:
+- rb-gpios: the GPIO(s) used to check the Ready/Busy status of the NAND.
+- cs-gpios: the GPIO(s) used to control the CS line.
+- det-gpios: the GPIO used to detect if a Smartmedia Card is present.
+- atmel,rb: an integer identifying the native Ready/Busy pin. Only meaningful
+ on sama5 SoCs.
+
+All generic properties described in
+Documentation/devicetree/bindings/mtd/{common,nand}.txt also apply to the NAND
+device node, and NAND partitions should be defined under the NAND node as
+described in Documentation/devicetree/bindings/mtd/partition.txt.
+
+* ECC engine (PMECC) bindings:
+
+Required properties:
+- compatible: should be one of the following
+ "atmel,at91sam9g45-pmecc"
+ "atmel,sama5d4-pmecc"
+ "atmel,sama5d2-pmecc"
+- reg: should contain 2 register ranges. The first one is pointing to the PMECC
+ block, and the second one to the PMECC_ERRLOC block.
+
+Example:
+
+ pmecc: ecc-engine@ffffc070 {
+ compatible = "atmel,at91sam9g45-pmecc";
+ reg = <0xffffc070 0x490>,
+ <0xffffc500 0x100>;
+ };
+
+ ebi: ebi@10000000 {
+ compatible = "atmel,sama5d3-ebi";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ atmel,smc = <&hsmc>;
+ reg = <0x10000000 0x10000000
+ 0x40000000 0x30000000>;
+ ranges = <0x0 0x0 0x10000000 0x10000000
+ 0x1 0x0 0x40000000 0x10000000
+ 0x2 0x0 0x50000000 0x10000000
+ 0x3 0x0 0x60000000 0x10000000>;
+ clocks = <&mck>;
+
+ nand_controller: nand-controller {
+ compatible = "atmel,sama5d3-nand-controller";
+ atmel,nfc-sram = <&nfc_sram>;
+ atmel,nfc-io = <&nfc_io>;
+ ecc-engine = <&pmecc>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges;
+
+ nand@3 {
+ reg = <0x3 0x0 0x800000>;
+ atmel,rb = <0>;
+
+ /*
+ * Put generic NAND/MTD properties and
+ * subnodes here.
+ */
+ };
+ };
+ };
+
+-----------------------------------------------------------------------
+
+Deprecated bindings (should not be used in new device trees):
Required properties:
- compatible: The possible values are:
Document the new DT bindings for the Atmel NAND controller and deprecate the old ones. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> --- .../devicetree/bindings/mtd/atmel-nand.txt | 106 ++++++++++++++++++++- 1 file changed, 105 insertions(+), 1 deletion(-)