@@ -483,6 +483,14 @@ config STM32_DMA
If you have a board based on such a MCU and wish to use DMA say Y
here.
+config SPRD_DMA
+ tristate "Spreadtrum DMA support"
+ depends on ARCH_SPRD || COMPILE_TEST
+ select DMA_ENGINE
+ select DMA_VIRTUAL_CHANNELS
+ help
+ Enable support for the on-chip DMA controller on Spreadtrum platform.
+
config S3C24XX_DMAC
bool "Samsung S3C24XX DMA support"
depends on ARCH_S3C24XX || COMPILE_TEST
@@ -59,6 +59,7 @@ obj-$(CONFIG_RENESAS_DMA) += sh/
obj-$(CONFIG_SIRF_DMA) += sirf-dma.o
obj-$(CONFIG_STE_DMA40) += ste_dma40.o ste_dma40_ll.o
obj-$(CONFIG_STM32_DMA) += stm32-dma.o
+obj-$(CONFIG_SPRD_DMA) += sprd-dma.o
obj-$(CONFIG_S3C24XX_DMAC) += s3c24xx-dma.o
obj-$(CONFIG_TXX9_DMAC) += txx9dmac.o
obj-$(CONFIG_TEGRA20_APB_DMA) += tegra20-apb-dma.o
new file mode 100644
@@ -0,0 +1,988 @@
+/*
+ * Copyright (C) 2017 Spreadtrum Communications Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_dma.h>
+#include <linux/of_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/slab.h>
+
+#include "virt-dma.h"
+
+#define SPRD_DMA_CHN_REG_OFFSET 0x1000
+#define SPRD_DMA_CHN_REG_LENGTH 0x40
+#define SPRD_DMA_MEMCPY_MIN_SIZE 64
+
+/* DMA global registers definition */
+#define SPRD_DMA_GLB_PAUSE 0x0
+#define SPRD_DMA_GLB_FRAG_WAIT 0x4
+#define SPRD_DMA_GLB_REQ_PEND0_EN 0x8
+#define SPRD_DMA_GLB_REQ_PEND1_EN 0xc
+#define SPRD_DMA_GLB_INT_RAW_STS 0x10
+#define SPRD_DMA_GLB_INT_MSK_STS 0x14
+#define SPRD_DMA_GLB_REQ_STS 0x18
+#define SPRD_DMA_GLB_CHN_EN_STS 0x1c
+#define SPRD_DMA_GLB_DEBUG_STS 0x20
+#define SPRD_DMA_GLB_ARB_SEL_STS 0x24
+#define SPRD_DMA_GLB_REQ_UID(uid) (0x4 * ((uid) - 1))
+#define SPRD_DMA_GLB_REQ_UID_OFFSET 0x2000
+
+/* DMA channel registers definition */
+#define SPRD_DMA_CHN_PAUSE 0x0
+#define SPRD_DMA_CHN_REQ 0x4
+#define SPRD_DMA_CHN_CFG 0x8
+#define SPRD_DMA_CHN_INTC 0xc
+#define SPRD_DMA_CHN_SRC_ADDR 0x10
+#define SPRD_DMA_CHN_DES_ADDR 0x14
+#define SPRD_DMA_CHN_FRG_LEN 0x18
+#define SPRD_DMA_CHN_BLK_LEN 0x1c
+#define SPRD_DMA_CHN_TRSC_LEN 0x20
+#define SPRD_DMA_CHN_TRSF_STEP 0x24
+#define SPRD_DMA_CHN_WARP_PTR 0x28
+#define SPRD_DMA_CHN_WARP_TO 0x2c
+#define SPRD_DMA_CHN_LLIST_PTR 0x30
+#define SPRD_DMA_CHN_FRAG_STEP 0x34
+#define SPRD_DMA_CHN_SRC_BLK_STEP 0x38
+#define SPRD_DMA_CHN_DES_BLK_STEP 0x3c
+
+/* SPRD_DMA_CHN_INTC register definition */
+#define SPRD_DMA_INT_MASK GENMASK(4, 0)
+#define SPRD_DMA_INT_CLR_OFFSET 24
+#define SPRD_DMA_FRAG_INT_EN BIT(0)
+#define SPRD_DMA_BLK_INT_EN BIT(1)
+#define SPRD_DMA_TRANS_INT_EN BIT(2)
+#define SPRD_DMA_LIST_INT_EN BIT(3)
+#define SPRD_DMA_CFG_ERR_INT_EN BIT(4)
+
+/* SPRD_DMA_CHN_CFG register definition */
+#define SPRD_DMA_CHN_EN BIT(0)
+#define SPRD_DMA_WAIT_BDONE_OFFSET 24
+#define SPRD_DMA_DONOT_WAIT_BDONE 1
+
+/* SPRD_DMA_CHN_REQ register definition */
+#define SPRD_DMA_REQ_EN BIT(0)
+
+/* SPRD_DMA_CHN_PAUSE register definition */
+#define SPRD_DMA_PAUSE_EN BIT(0)
+#define SPRD_DMA_PAUSE_STS BIT(2)
+#define SPRD_DMA_PAUSE_CNT 0x2000
+
+/* DMA_CHN_WARP_* register definition */
+#define SPRD_DMA_HIGH_ADDR_MASK GENMASK(31, 28)
+#define SPRD_DMA_LOW_ADDR_MASK GENMASK(31, 0)
+#define SPRD_DMA_HIGH_ADDR_OFFSET 4
+
+/* SPRD_DMA_CHN_INTC register definition */
+#define SPRD_DMA_FRAG_INT_STS BIT(16)
+#define SPRD_DMA_BLK_INT_STS BIT(17)
+#define SPRD_DMA_TRSC_INT_STS BIT(18)
+#define SPRD_DMA_LIST_INT_STS BIT(19)
+#define SPRD_DMA_CFGERR_INT_STS BIT(20)
+#define SPRD_DMA_CHN_INT_STS \
+ (SPRD_DMA_FRAG_INT_STS | SPRD_DMA_BLK_INT_STS | \
+ SPRD_DMA_TRSC_INT_STS | SPRD_DMA_LIST_INT_STS | \
+ SPRD_DMA_CFGERR_INT_STS)
+
+/* SPRD_DMA_CHN_FRG_LEN register definition */
+#define SPRD_DMA_SRC_DATAWIDTH_OFFSET 30
+#define SPRD_DMA_DES_DATAWIDTH_OFFSET 28
+#define SPRD_DMA_SWT_MODE_OFFSET 26
+#define SPRD_DMA_REQ_MODE_OFFSET 24
+#define SPRD_DMA_REQ_MODE_MASK GENMASK(1, 0)
+#define SPRD_DMA_FIX_SEL_OFFSET 21
+#define SPRD_DMA_FIX_EN_OFFSET 20
+#define SPRD_DMA_LLIST_END_OFFSET 19
+#define SPRD_DMA_FRG_LEN_MASK GENMASK(16, 0)
+
+/* SPRD_DMA_CHN_BLK_LEN register definition */
+#define SPRD_DMA_BLK_LEN_MASK GENMASK(16, 0)
+
+/* SPRD_DMA_CHN_TRSC_LEN register definition */
+#define SPRD_DMA_TRSC_LEN_MASK GENMASK(27, 0)
+
+/* SPRD_DMA_CHN_TRSF_STEP register definition */
+#define SPRD_DMA_DEST_TRSF_STEP_OFFSET 16
+#define SPRD_DMA_SRC_TRSF_STEP_OFFSET 0
+#define SPRD_DMA_TRSF_STEP_MASK GENMASK(15, 0)
+
+#define SPRD_DMA_SOFTWARE_UID 0
+
+/*
+ * enum sprd_dma_req_mode: define the DMA request mode
+ * @SPRD_DMA_FRAG_REQ: fragment request mode
+ * @SPRD_DMA_BLK_REQ: block request mode
+ * @SPRD_DMA_TRANS_REQ: transaction request mode
+ * @SPRD_DMA_LIST_REQ: link-list request mode
+ *
+ * We have 4 types request mode: fragment mode, block mode, transaction mode
+ * and linklist mode. One transaction can contain several blocks, one block can
+ * contain several fragments. Link-list mode means we can save several DMA
+ * configuration into one reserved memory, then DMA can fetch each DMA
+ * configuration automatically to start transfer.
+ */
+enum sprd_dma_req_mode {
+ SPRD_DMA_FRAG_REQ,
+ SPRD_DMA_BLK_REQ,
+ SPRD_DMA_TRANS_REQ,
+ SPRD_DMA_LIST_REQ,
+};
+
+/*
+ * enum sprd_dma_int_type: define the DMA interrupt type
+ * @SPRD_DMA_NO_INT: do not need generate DMA interrupts.
+ * @SPRD_DMA_FRAG_INT: fragment done interrupt when one fragment request
+ * is done.
+ * @SPRD_DMA_BLK_INT: block done interrupt when one block request is done.
+ * @SPRD_DMA_BLK_FRAG_INT: block and fragment interrupt when one fragment
+ * or one block request is done.
+ * @SPRD_DMA_TRANS_INT: tansaction done interrupt when one transaction
+ * request is done.
+ * @SPRD_DMA_TRANS_FRAG_INT: transaction and fragment interrupt when one
+ * transaction request or fragment request is done.
+ * @SPRD_DMA_TRANS_BLK_INT: transaction and block interrupt when one
+ * transaction request or block request is done.
+ * @SPRD_DMA_LIST_INT: link-list done interrupt when one link-list request
+ * is done.
+ * @SPRD_DMA_CFGERR_INT: configure error interrupt when configuration is
+ * incorrect.
+ */
+enum sprd_dma_int_type {
+ SPRD_DMA_NO_INT,
+ SPRD_DMA_FRAG_INT,
+ SPRD_DMA_BLK_INT,
+ SPRD_DMA_BLK_FRAG_INT,
+ SPRD_DMA_TRANS_INT,
+ SPRD_DMA_TRANS_FRAG_INT,
+ SPRD_DMA_TRANS_BLK_INT,
+ SPRD_DMA_LIST_INT,
+ SPRD_DMA_CFGERR_INT,
+};
+
+/* dma channel hardware configuration */
+struct sprd_dma_chn_hw {
+ u32 pause;
+ u32 req;
+ u32 cfg;
+ u32 intc;
+ u32 src_addr;
+ u32 des_addr;
+ u32 frg_len;
+ u32 blk_len;
+ u32 trsc_len;
+ u32 trsf_step;
+ u32 wrap_ptr;
+ u32 wrap_to;
+ u32 llist_ptr;
+ u32 frg_step;
+ u32 src_blk_step;
+ u32 des_blk_step;
+};
+
+/* dma request description */
+struct sprd_dma_desc {
+ struct virt_dma_desc vd;
+ struct sprd_dma_chn_hw chn_hw;
+};
+
+/* dma channel description */
+struct sprd_dma_chn {
+ struct virt_dma_chan vc;
+ void __iomem *chn_base;
+ u32 chn_num;
+ u32 dev_id;
+ struct sprd_dma_desc *cur_desc;
+};
+
+/* SPRD dma device */
+struct sprd_dma_dev {
+ struct dma_device dma_dev;
+ void __iomem *glb_base;
+ struct clk *clk;
+ struct clk *ashb_clk;
+ int irq;
+ u32 total_chns;
+ struct sprd_dma_chn channels[0];
+};
+
+static bool sprd_dma_filter_fn(struct dma_chan *chan, void *param);
+static struct of_dma_filter_info sprd_dma_info = {
+ .filter_fn = sprd_dma_filter_fn,
+};
+
+static inline struct sprd_dma_chn *to_sprd_dma_chan(struct dma_chan *c)
+{
+ return container_of(c, struct sprd_dma_chn, vc.chan);
+}
+
+static inline struct sprd_dma_dev *to_sprd_dma_dev(struct dma_chan *c)
+{
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(c);
+
+ return container_of(schan, struct sprd_dma_dev, channels[c->chan_id]);
+}
+
+static inline struct sprd_dma_desc *to_sprd_dma_desc(struct virt_dma_desc *vd)
+{
+ return container_of(vd, struct sprd_dma_desc, vd);
+}
+
+static void sprd_dma_chn_update(struct sprd_dma_chn *schan, u32 reg,
+ u32 mask, u32 val)
+{
+ u32 orig = readl(schan->chn_base + reg);
+ u32 tmp;
+
+ tmp = (orig & ~mask) | val;
+ writel(tmp, schan->chn_base + reg);
+}
+
+static int sprd_dma_enable(struct sprd_dma_dev *sdev)
+{
+ int ret;
+
+ ret = clk_prepare_enable(sdev->clk);
+ if (ret)
+ return ret;
+
+ /*
+ * The ashb_clk is optional and only for AGCP DMA controller, so we
+ * need add one condition to check if the ashb_clk need enable.
+ */
+ if (!IS_ERR(sdev->ashb_clk))
+ ret = clk_prepare_enable(sdev->ashb_clk);
+
+ return ret;
+}
+
+static void sprd_dma_disable(struct sprd_dma_dev *sdev)
+{
+ clk_disable_unprepare(sdev->clk);
+
+ /*
+ * Need to check if we need disable the optional ashb_clk for AGCP DMA.
+ */
+ if (!IS_ERR(sdev->ashb_clk))
+ clk_disable_unprepare(sdev->ashb_clk);
+}
+
+static void sprd_dma_set_uid(struct sprd_dma_chn *schan)
+{
+ struct sprd_dma_dev *sdev = to_sprd_dma_dev(&schan->vc.chan);
+ u32 dev_id = schan->dev_id;
+
+ if (dev_id != SPRD_DMA_SOFTWARE_UID) {
+ u32 uid_offset = SPRD_DMA_GLB_REQ_UID_OFFSET +
+ SPRD_DMA_GLB_REQ_UID(dev_id);
+
+ writel(schan->chn_num + 1, sdev->glb_base + uid_offset);
+ }
+}
+
+static void sprd_dma_unset_uid(struct sprd_dma_chn *schan)
+{
+ struct sprd_dma_dev *sdev = to_sprd_dma_dev(&schan->vc.chan);
+ u32 dev_id = schan->dev_id;
+
+ if (dev_id != SPRD_DMA_SOFTWARE_UID) {
+ u32 uid_offset = SPRD_DMA_GLB_REQ_UID_OFFSET +
+ SPRD_DMA_GLB_REQ_UID(dev_id);
+
+ writel(0, sdev->glb_base + uid_offset);
+ }
+}
+
+static void sprd_dma_clear_int(struct sprd_dma_chn *schan)
+{
+ sprd_dma_chn_update(schan, SPRD_DMA_CHN_INTC,
+ SPRD_DMA_INT_MASK << SPRD_DMA_INT_CLR_OFFSET,
+ SPRD_DMA_INT_MASK << SPRD_DMA_INT_CLR_OFFSET);
+}
+
+static void sprd_dma_enable_chn(struct sprd_dma_chn *schan)
+{
+ sprd_dma_chn_update(schan, SPRD_DMA_CHN_CFG, SPRD_DMA_CHN_EN,
+ SPRD_DMA_CHN_EN);
+}
+
+static void sprd_dma_disable_chn(struct sprd_dma_chn *schan)
+{
+ sprd_dma_chn_update(schan, SPRD_DMA_CHN_CFG, SPRD_DMA_CHN_EN, 0);
+}
+
+static void sprd_dma_soft_request(struct sprd_dma_chn *schan)
+{
+ sprd_dma_chn_update(schan, SPRD_DMA_CHN_REQ, SPRD_DMA_REQ_EN,
+ SPRD_DMA_REQ_EN);
+}
+
+static void sprd_dma_pause_resume(struct sprd_dma_chn *schan, bool enable)
+{
+ struct sprd_dma_dev *sdev = to_sprd_dma_dev(&schan->vc.chan);
+ u32 pause, timeout = SPRD_DMA_PAUSE_CNT;
+
+ if (enable) {
+ sprd_dma_chn_update(schan, SPRD_DMA_CHN_PAUSE,
+ SPRD_DMA_PAUSE_EN, SPRD_DMA_PAUSE_EN);
+
+ do {
+ pause = readl(schan->chn_base + SPRD_DMA_CHN_PAUSE);
+ if (pause & SPRD_DMA_PAUSE_STS)
+ break;
+
+ cpu_relax();
+ } while (--timeout > 0);
+
+ if (!timeout)
+ dev_warn(sdev->dma_dev.dev,
+ "pause dma controller timeout\n");
+ } else {
+ sprd_dma_chn_update(schan, SPRD_DMA_CHN_PAUSE,
+ SPRD_DMA_PAUSE_EN, 0);
+ }
+}
+
+static void sprd_dma_stop_and_disable(struct sprd_dma_chn *schan)
+{
+ u32 cfg = readl(schan->chn_base + SPRD_DMA_CHN_CFG);
+
+ if (!(cfg & SPRD_DMA_CHN_EN))
+ return;
+
+ sprd_dma_pause_resume(schan, true);
+ sprd_dma_disable_chn(schan);
+}
+
+static unsigned long sprd_dma_get_dst_addr(struct sprd_dma_chn *schan)
+{
+ unsigned long addr, addr_high;
+
+ addr = readl(schan->chn_base + SPRD_DMA_CHN_DES_ADDR);
+ addr_high = readl(schan->chn_base + SPRD_DMA_CHN_WARP_TO) &
+ SPRD_DMA_HIGH_ADDR_MASK;
+
+ return addr | (addr_high << SPRD_DMA_HIGH_ADDR_OFFSET);
+}
+
+static enum sprd_dma_int_type sprd_dma_get_int_type(struct sprd_dma_chn *schan)
+{
+ struct sprd_dma_dev *sdev = to_sprd_dma_dev(&schan->vc.chan);
+ u32 intc_sts = readl(schan->chn_base + SPRD_DMA_CHN_INTC) &
+ SPRD_DMA_CHN_INT_STS;
+
+ switch (intc_sts) {
+ case SPRD_DMA_CFGERR_INT_STS:
+ return SPRD_DMA_CFGERR_INT;
+
+ case SPRD_DMA_LIST_INT_STS:
+ return SPRD_DMA_LIST_INT;
+
+ case SPRD_DMA_TRSC_INT_STS:
+ return SPRD_DMA_TRANS_INT;
+
+ case SPRD_DMA_BLK_INT_STS:
+ return SPRD_DMA_BLK_INT;
+
+ case SPRD_DMA_FRAG_INT_STS:
+ return SPRD_DMA_FRAG_INT;
+
+ default:
+ dev_warn(sdev->dma_dev.dev, "incorrect dma interrupt type\n");
+ return SPRD_DMA_NO_INT;
+ }
+}
+
+static enum sprd_dma_req_mode sprd_dma_get_req_type(struct sprd_dma_chn *schan)
+{
+ u32 frag_reg = readl(schan->chn_base + SPRD_DMA_CHN_FRG_LEN);
+
+ return (frag_reg >> SPRD_DMA_REQ_MODE_OFFSET) & SPRD_DMA_REQ_MODE_MASK;
+}
+
+static void sprd_dma_set_chn_config(struct sprd_dma_chn *schan,
+ struct sprd_dma_desc *sdesc)
+{
+ struct sprd_dma_chn_hw *cfg = &sdesc->chn_hw;
+
+ writel(cfg->pause, schan->chn_base + SPRD_DMA_CHN_PAUSE);
+ writel(cfg->cfg, schan->chn_base + SPRD_DMA_CHN_CFG);
+ writel(cfg->intc, schan->chn_base + SPRD_DMA_CHN_INTC);
+ writel(cfg->src_addr, schan->chn_base + SPRD_DMA_CHN_SRC_ADDR);
+ writel(cfg->des_addr, schan->chn_base + SPRD_DMA_CHN_DES_ADDR);
+ writel(cfg->frg_len, schan->chn_base + SPRD_DMA_CHN_FRG_LEN);
+ writel(cfg->blk_len, schan->chn_base + SPRD_DMA_CHN_BLK_LEN);
+ writel(cfg->trsc_len, schan->chn_base + SPRD_DMA_CHN_TRSC_LEN);
+ writel(cfg->trsf_step, schan->chn_base + SPRD_DMA_CHN_TRSF_STEP);
+ writel(cfg->wrap_ptr, schan->chn_base + SPRD_DMA_CHN_WARP_PTR);
+ writel(cfg->wrap_to, schan->chn_base + SPRD_DMA_CHN_WARP_TO);
+ writel(cfg->llist_ptr, schan->chn_base + SPRD_DMA_CHN_LLIST_PTR);
+ writel(cfg->frg_step, schan->chn_base + SPRD_DMA_CHN_FRAG_STEP);
+ writel(cfg->src_blk_step, schan->chn_base + SPRD_DMA_CHN_SRC_BLK_STEP);
+ writel(cfg->des_blk_step, schan->chn_base + SPRD_DMA_CHN_DES_BLK_STEP);
+ writel(cfg->req, schan->chn_base + SPRD_DMA_CHN_REQ);
+}
+
+static void sprd_dma_start(struct sprd_dma_chn *schan)
+{
+ struct virt_dma_desc *vd = vchan_next_desc(&schan->vc);
+
+ if (!vd)
+ return;
+
+ list_del(&vd->node);
+ schan->cur_desc = to_sprd_dma_desc(vd);
+
+ /*
+ * Copy the DMA configuration from DMA descriptor to this hardware
+ * channel.
+ */
+ sprd_dma_set_chn_config(schan, schan->cur_desc);
+ sprd_dma_set_uid(schan);
+ sprd_dma_enable_chn(schan);
+
+ if (schan->dev_id == SPRD_DMA_SOFTWARE_UID)
+ sprd_dma_soft_request(schan);
+}
+
+static void sprd_dma_stop(struct sprd_dma_chn *schan)
+{
+ sprd_dma_stop_and_disable(schan);
+ sprd_dma_unset_uid(schan);
+ sprd_dma_clear_int(schan);
+}
+
+static bool sprd_dma_check_trans_done(struct sprd_dma_desc *sdesc,
+ enum sprd_dma_int_type int_type,
+ enum sprd_dma_req_mode req_mode)
+{
+ if (int_type == SPRD_DMA_NO_INT)
+ return false;
+
+ if (int_type >= req_mode + 1)
+ return true;
+ else
+ return false;
+}
+
+static irqreturn_t dma_irq_handle(int irq, void *dev_id)
+{
+ struct sprd_dma_dev *sdev = (struct sprd_dma_dev *)dev_id;
+ u32 irq_status = readl(sdev->glb_base + SPRD_DMA_GLB_INT_MSK_STS);
+ struct sprd_dma_chn *schan;
+ struct sprd_dma_desc *sdesc;
+ enum sprd_dma_req_mode req_type;
+ enum sprd_dma_int_type int_type;
+ bool trans_done = false;
+ u32 i;
+
+ while (irq_status) {
+ i = __ffs(irq_status);
+ irq_status &= (irq_status - 1);
+ schan = &sdev->channels[i];
+
+ spin_lock(&schan->vc.lock);
+ int_type = sprd_dma_get_int_type(schan);
+ req_type = sprd_dma_get_req_type(schan);
+ sprd_dma_clear_int(schan);
+
+ sdesc = schan->cur_desc;
+
+ /* Check if the dma request descriptor is done. */
+ trans_done = sprd_dma_check_trans_done(sdesc, int_type,
+ req_type);
+ if (trans_done == true) {
+ vchan_cookie_complete(&sdesc->vd);
+ schan->cur_desc = NULL;
+ sprd_dma_start(schan);
+ }
+ spin_unlock(&schan->vc.lock);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int sprd_dma_alloc_chan_resources(struct dma_chan *chan)
+{
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
+ int ret;
+
+ ret = pm_runtime_get_sync(chan->device->dev);
+ if (ret < 0)
+ return ret;
+
+ schan->dev_id = SPRD_DMA_SOFTWARE_UID;
+ return 0;
+}
+
+static void sprd_dma_free_chan_resources(struct dma_chan *chan)
+{
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
+ unsigned long flags;
+
+ spin_lock_irqsave(&schan->vc.lock, flags);
+ sprd_dma_stop(schan);
+ spin_unlock_irqrestore(&schan->vc.lock, flags);
+
+ vchan_free_chan_resources(&schan->vc);
+ pm_runtime_put(chan->device->dev);
+}
+
+static enum dma_status sprd_dma_tx_status(struct dma_chan *chan,
+ dma_cookie_t cookie,
+ struct dma_tx_state *txstate)
+{
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
+ struct virt_dma_desc *vd;
+ unsigned long flags;
+ enum dma_status ret;
+ u32 pos;
+
+ ret = dma_cookie_status(chan, cookie, txstate);
+ if (ret == DMA_COMPLETE || !txstate)
+ return ret;
+
+ spin_lock_irqsave(&schan->vc.lock, flags);
+ vd = vchan_find_desc(&schan->vc, cookie);
+ if (vd) {
+ struct sprd_dma_desc *sdesc = to_sprd_dma_desc(vd);
+ struct sprd_dma_chn_hw *hw = &sdesc->chn_hw;
+
+ if (hw->trsc_len > 0)
+ pos = hw->trsc_len;
+ else if (hw->blk_len > 0)
+ pos = hw->blk_len;
+ else if (hw->frg_len > 0)
+ pos = hw->frg_len;
+ else
+ pos = 0;
+ } else if (schan->cur_desc && schan->cur_desc->vd.tx.cookie == cookie) {
+ pos = sprd_dma_get_dst_addr(schan);
+ } else {
+ pos = 0;
+ }
+ spin_unlock_irqrestore(&schan->vc.lock, flags);
+
+ dma_set_residue(txstate, pos);
+ return ret;
+}
+
+static void sprd_dma_issue_pending(struct dma_chan *chan)
+{
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
+ unsigned long flags;
+
+ spin_lock_irqsave(&schan->vc.lock, flags);
+ if (vchan_issue_pending(&schan->vc) && !schan->cur_desc)
+ sprd_dma_start(schan);
+ spin_unlock_irqrestore(&schan->vc.lock, flags);
+}
+
+static int sprd_dma_config(struct dma_chan *chan, struct sprd_dma_desc *sdesc,
+ dma_addr_t dest, dma_addr_t src, size_t len)
+{
+ struct sprd_dma_dev *sdev = to_sprd_dma_dev(chan);
+ struct sprd_dma_chn_hw *hw = &sdesc->chn_hw;
+ u32 datawidth, src_step, des_step, fragment_len;
+ u32 block_len, req_mode, irq_mode, transcation_len;
+ u32 fix_mode = 0, fix_en = 0;
+
+ if (IS_ALIGNED(len, 4)) {
+ datawidth = 2;
+ src_step = 4;
+ des_step = 4;
+ } else if (IS_ALIGNED(len, 2)) {
+ datawidth = 1;
+ src_step = 2;
+ des_step = 2;
+ } else {
+ datawidth = 0;
+ src_step = 1;
+ des_step = 1;
+ }
+
+ fragment_len = SPRD_DMA_MEMCPY_MIN_SIZE;
+ if (len <= SPRD_DMA_BLK_LEN_MASK) {
+ block_len = len;
+ transcation_len = 0;
+ req_mode = SPRD_DMA_BLK_REQ;
+ irq_mode = SPRD_DMA_BLK_INT;
+ } else {
+ block_len = SPRD_DMA_MEMCPY_MIN_SIZE;
+ transcation_len = len;
+ req_mode = SPRD_DMA_TRANS_REQ;
+ irq_mode = SPRD_DMA_TRANS_INT;
+ }
+
+ hw->cfg = SPRD_DMA_DONOT_WAIT_BDONE << SPRD_DMA_WAIT_BDONE_OFFSET;
+ hw->wrap_ptr = (u32)((src >> SPRD_DMA_HIGH_ADDR_OFFSET) &
+ SPRD_DMA_HIGH_ADDR_MASK);
+ hw->wrap_to = (u32)((dest >> SPRD_DMA_HIGH_ADDR_OFFSET) &
+ SPRD_DMA_HIGH_ADDR_MASK);
+
+ hw->src_addr = (u32)(src & SPRD_DMA_LOW_ADDR_MASK);
+ hw->des_addr = (u32)(dest & SPRD_DMA_LOW_ADDR_MASK);
+
+ if ((src_step != 0 && des_step != 0) || (src_step | des_step) == 0) {
+ fix_en = 0;
+ } else {
+ fix_en = 1;
+ if (src_step)
+ fix_mode = 1;
+ else
+ fix_mode = 0;
+ }
+
+ hw->frg_len = datawidth << SPRD_DMA_SRC_DATAWIDTH_OFFSET |
+ datawidth << SPRD_DMA_DES_DATAWIDTH_OFFSET |
+ req_mode << SPRD_DMA_REQ_MODE_OFFSET |
+ fix_mode << SPRD_DMA_FIX_SEL_OFFSET |
+ fix_en << SPRD_DMA_FIX_EN_OFFSET |
+ (fragment_len & SPRD_DMA_FRG_LEN_MASK);
+ hw->blk_len = block_len & SPRD_DMA_BLK_LEN_MASK;
+
+ hw->intc = SPRD_DMA_CFG_ERR_INT_EN;
+
+ switch (irq_mode) {
+ case SPRD_DMA_NO_INT:
+ break;
+
+ case SPRD_DMA_FRAG_INT:
+ hw->intc |= SPRD_DMA_FRAG_INT_EN;
+ break;
+
+ case SPRD_DMA_BLK_INT:
+ hw->intc |= SPRD_DMA_BLK_INT_EN;
+ break;
+
+ case SPRD_DMA_BLK_FRAG_INT:
+ hw->intc |= SPRD_DMA_BLK_INT_EN | SPRD_DMA_FRAG_INT_EN;
+ break;
+
+ case SPRD_DMA_TRANS_INT:
+ hw->intc |= SPRD_DMA_TRANS_INT_EN;
+ break;
+
+ case SPRD_DMA_TRANS_FRAG_INT:
+ hw->intc |= SPRD_DMA_TRANS_INT_EN | SPRD_DMA_FRAG_INT_EN;
+ break;
+
+ case SPRD_DMA_TRANS_BLK_INT:
+ hw->intc |= SPRD_DMA_TRANS_INT_EN | SPRD_DMA_BLK_INT_EN;
+ break;
+
+ case SPRD_DMA_LIST_INT:
+ hw->intc |= SPRD_DMA_LIST_INT_EN;
+ break;
+
+ case SPRD_DMA_CFGERR_INT:
+ hw->intc |= SPRD_DMA_CFG_ERR_INT_EN;
+ break;
+
+ default:
+ dev_err(sdev->dma_dev.dev, "invalid irq mode\n");
+ return -EINVAL;
+ }
+
+ if (transcation_len == 0)
+ hw->trsc_len = block_len & SPRD_DMA_TRSC_LEN_MASK;
+ else
+ hw->trsc_len = transcation_len & SPRD_DMA_TRSC_LEN_MASK;
+
+ hw->trsf_step = (des_step & SPRD_DMA_TRSF_STEP_MASK) <<
+ SPRD_DMA_DEST_TRSF_STEP_OFFSET |
+ (src_step & SPRD_DMA_TRSF_STEP_MASK) <<
+ SPRD_DMA_SRC_TRSF_STEP_OFFSET;
+
+ hw->frg_step = 0;
+ hw->src_blk_step = 0;
+ hw->des_blk_step = 0;
+ hw->src_blk_step = 0;
+ return 0;
+}
+
+struct dma_async_tx_descriptor *
+sprd_dma_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
+ size_t len, unsigned long flags)
+{
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
+ struct sprd_dma_desc *sdesc;
+ int ret;
+
+ sdesc = kzalloc(sizeof(*sdesc), GFP_NOWAIT);
+ if (!sdesc)
+ return NULL;
+
+ ret = sprd_dma_config(chan, sdesc, dest, src, len);
+ if (ret) {
+ kfree(sdesc);
+ return NULL;
+ }
+
+ return vchan_tx_prep(&schan->vc, &sdesc->vd, flags);
+}
+
+static int sprd_dma_pause(struct dma_chan *chan)
+{
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
+ unsigned long flags;
+
+ spin_lock_irqsave(&schan->vc.lock, flags);
+ sprd_dma_pause_resume(schan, true);
+ spin_unlock_irqrestore(&schan->vc.lock, flags);
+
+ return 0;
+}
+
+static int sprd_dma_resume(struct dma_chan *chan)
+{
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
+ unsigned long flags;
+
+ spin_lock_irqsave(&schan->vc.lock, flags);
+ sprd_dma_pause_resume(schan, false);
+ spin_unlock_irqrestore(&schan->vc.lock, flags);
+
+ return 0;
+}
+
+static int sprd_dma_terminate_all(struct dma_chan *chan)
+{
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
+ unsigned long flags;
+ LIST_HEAD(head);
+
+ spin_lock_irqsave(&schan->vc.lock, flags);
+ sprd_dma_stop(schan);
+
+ vchan_get_all_descriptors(&schan->vc, &head);
+ spin_unlock_irqrestore(&schan->vc.lock, flags);
+
+ vchan_dma_desc_free_list(&schan->vc, &head);
+ return 0;
+}
+
+static void sprd_dma_free_desc(struct virt_dma_desc *vd)
+{
+ struct sprd_dma_desc *sdesc = to_sprd_dma_desc(vd);
+
+ kfree(sdesc);
+}
+
+static bool sprd_dma_filter_fn(struct dma_chan *chan, void *param)
+{
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
+ struct sprd_dma_dev *sdev = to_sprd_dma_dev(&schan->vc.chan);
+ u32 req = *(u32 *)param;
+
+ if (req < sdev->total_chns)
+ return req == schan->chn_num + 1;
+ else
+ return false;
+}
+
+static int sprd_dma_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct sprd_dma_dev *sdev;
+ struct sprd_dma_chn *dma_chn;
+ struct resource *res;
+ u32 chn_count;
+ int ret, i;
+
+ ret = device_property_read_u32(&pdev->dev, "#dma-channels", &chn_count);
+ if (ret) {
+ dev_err(&pdev->dev, "get dma channels count failed\n");
+ return ret;
+ }
+
+ sdev = devm_kzalloc(&pdev->dev, sizeof(*sdev) +
+ sizeof(*dma_chn) * chn_count,
+ GFP_KERNEL);
+ if (!sdev)
+ return -ENOMEM;
+
+ sdev->clk = devm_clk_get(&pdev->dev, "enable");
+ if (IS_ERR(sdev->clk)) {
+ dev_err(&pdev->dev, "get enable clock failed\n");
+ return PTR_ERR(sdev->clk);
+ }
+
+ /* ashb clock is optional for AGCP DMA */
+ sdev->ashb_clk = devm_clk_get(&pdev->dev, "ashb_eb");
+ if (IS_ERR(sdev->ashb_clk))
+ dev_warn(&pdev->dev, "no optional ashb eb clock\n");
+
+ /*
+ * We have three DMA controllers: AP DMA, AON DMA and AGCP DMA. For AGCP
+ * DMA controller, it can or do not request the irq, which will save
+ * system power without resuming system by DMA interrupts if AGCP DMA
+ * does not request the irq. Thus the DMA interrupts property should
+ * be optional.
+ */
+ sdev->irq = platform_get_irq(pdev, 0);
+ if (sdev->irq > 0) {
+ ret = devm_request_irq(&pdev->dev, sdev->irq, dma_irq_handle,
+ 0, "sprd_dma", (void *)sdev);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "request dma irq failed\n");
+ return ret;
+ }
+ } else {
+ dev_warn(&pdev->dev, "no interrupts for the dma controller\n");
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ sdev->glb_base = devm_ioremap_nocache(&pdev->dev, res->start,
+ resource_size(res));
+ if (!sdev->glb_base)
+ return -ENOMEM;
+
+ dma_cap_set(DMA_MEMCPY, sdev->dma_dev.cap_mask);
+ sdev->total_chns = chn_count;
+ sdev->dma_dev.chancnt = chn_count;
+ INIT_LIST_HEAD(&sdev->dma_dev.channels);
+ INIT_LIST_HEAD(&sdev->dma_dev.global_node);
+ sdev->dma_dev.dev = &pdev->dev;
+ sdev->dma_dev.device_alloc_chan_resources = sprd_dma_alloc_chan_resources;
+ sdev->dma_dev.device_free_chan_resources = sprd_dma_free_chan_resources;
+ sdev->dma_dev.device_tx_status = sprd_dma_tx_status;
+ sdev->dma_dev.device_issue_pending = sprd_dma_issue_pending;
+ sdev->dma_dev.device_prep_dma_memcpy = sprd_dma_prep_dma_memcpy;
+ sdev->dma_dev.device_pause = sprd_dma_pause;
+ sdev->dma_dev.device_resume = sprd_dma_resume;
+ sdev->dma_dev.device_terminate_all = sprd_dma_terminate_all;
+
+ for (i = 0; i < chn_count; i++) {
+ dma_chn = &sdev->channels[i];
+ dma_chn->chn_num = i;
+ dma_chn->cur_desc = NULL;
+ /* get each channel's registers base address. */
+ dma_chn->chn_base = sdev->glb_base + SPRD_DMA_CHN_REG_OFFSET +
+ SPRD_DMA_CHN_REG_LENGTH * i;
+
+ dma_chn->vc.desc_free = sprd_dma_free_desc;
+ vchan_init(&dma_chn->vc, &sdev->dma_dev);
+ }
+
+ platform_set_drvdata(pdev, sdev);
+ ret = sprd_dma_enable(sdev);
+ if (ret)
+ return ret;
+
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+
+ ret = pm_runtime_get_sync(&pdev->dev);
+ if (ret < 0)
+ goto err_rpm;
+
+ ret = dma_async_device_register(&sdev->dma_dev);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "register dma device failed:%d\n", ret);
+ goto err_register;
+ }
+
+ sprd_dma_info.dma_cap = sdev->dma_dev.cap_mask;
+ ret = of_dma_controller_register(np, of_dma_simple_xlate,
+ &sprd_dma_info);
+ if (ret)
+ goto err_of_register;
+
+ pm_runtime_put(&pdev->dev);
+ return 0;
+
+err_of_register:
+ dma_async_device_unregister(&sdev->dma_dev);
+err_register:
+ pm_runtime_put_noidle(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+err_rpm:
+ sprd_dma_disable(sdev);
+ return ret;
+}
+
+static int sprd_dma_remove(struct platform_device *pdev)
+{
+ struct sprd_dma_dev *sdev = platform_get_drvdata(pdev);
+ struct sprd_dma_chn *c, *cn;
+ int ret;
+
+ ret = pm_runtime_get_sync(&pdev->dev);
+ if (ret < 0)
+ return ret;
+
+ /* explicitly free the irq */
+ if (sdev->irq > 0)
+ devm_free_irq(&pdev->dev, sdev->irq, sdev);
+
+ list_for_each_entry_safe(c, cn, &sdev->dma_dev.channels,
+ vc.chan.device_node) {
+ list_del(&c->vc.chan.device_node);
+ tasklet_kill(&c->vc.task);
+ }
+
+ of_dma_controller_free(pdev->dev.of_node);
+ dma_async_device_unregister(&sdev->dma_dev);
+ sprd_dma_disable(sdev);
+
+ pm_runtime_put_noidle(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+ return 0;
+}
+
+static const struct of_device_id sprd_dma_match[] = {
+ { .compatible = "sprd,sc9860-dma", },
+ {},
+};
+
+static int __maybe_unused sprd_dma_runtime_suspend(struct device *dev)
+{
+ struct sprd_dma_dev *sdev = dev_get_drvdata(dev);
+
+ sprd_dma_disable(sdev);
+ return 0;
+}
+
+static int __maybe_unused sprd_dma_runtime_resume(struct device *dev)
+{
+ struct sprd_dma_dev *sdev = dev_get_drvdata(dev);
+ int ret;
+
+ ret = sprd_dma_enable(sdev);
+ if (ret)
+ dev_err(sdev->dma_dev.dev, "enable dma failed\n");
+
+ return ret;
+}
+
+static const struct dev_pm_ops sprd_dma_pm_ops = {
+ SET_RUNTIME_PM_OPS(sprd_dma_runtime_suspend,
+ sprd_dma_runtime_resume,
+ NULL)
+};
+
+static struct platform_driver sprd_dma_driver = {
+ .probe = sprd_dma_probe,
+ .remove = sprd_dma_remove,
+ .driver = {
+ .name = "sprd-dma",
+ .of_match_table = sprd_dma_match,
+ .pm = &sprd_dma_pm_ops,
+ },
+};
+module_platform_driver(sprd_dma_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("DMA driver for Spreadtrum");
+MODULE_AUTHOR("Baolin Wang <baolin.wang@spreadtrum.com>");
+MODULE_ALIAS("platform:sprd-dma");
This patch adds the DMA controller driver for Spreadtrum SC9860 platform. Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com> --- Changes since v4: - Correct lisence. - Rename SPRD_DMA_WAIT_BDONE macro to SPRD_DMA_WAIT_BDONE_OFFSET. - Optimize sprd_dma_chn_update() function. - Print warning when getting incorrect interrupt type in sprd_dma_get_int_type() and will check the incorrect interrupt type in sprd_dma_check_trans_done(). - Check if txstate is valid in sprd_dma_tx_status(). - Replace of_property_read_u32() with device_property_read_u32(). - Other coding style fixes. Changes since v3: - Remove reduandant local 'mask' and 'val' variables. - Simplify sprd_dma_get_req_type() function. - Change pm_runtime_put_sync() to pm_runtime_put() in probe function. - Simplify sizeof function. - Other coding style fixes. Changes since v2: - Add COMPILE_TEST as dependency. - Renamed DMA macro definition properly. - Add sprd_dma_chn_update() helpers to save lots of code. - Change pm_runtime_put_sync() to pm_runtime_put() when free resources. - Re-implement the sprd_dma_tx_status() function. - Free irq and kill tasklet when remove driver. - Add some documentaion. - Change to module_init() level and add MODULE_ALIAS(). - Other coding style fixes. Changes since v1: - Use virt-dma to manage dma descriptors. - Remove link-list and channel-start-channel Spreadtrum special features. - Remove device_config implementation. - Other optimization. Note: This patch just implemented the basic DMA_MEMCPY function, and in future we will send new patches to introduce some Speadtrum special features, that will be talk about how to handle these features easily instead of in one big patch which is hard to review. --- drivers/dma/Kconfig | 8 + drivers/dma/Makefile | 1 + drivers/dma/sprd-dma.c | 988 ++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 997 insertions(+) create mode 100644 drivers/dma/sprd-dma.c