deleted file mode 100644
@@ -1,22 +0,0 @@
-# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
-%YAML 1.2
----
-$id: http://devicetree.org/schemas/arm/calxeda.yaml#
-$schema: http://devicetree.org/meta-schemas/core.yaml#
-
-title: Calxeda Platforms Device Tree Bindings
-
-maintainers:
- - Rob Herring <robh@kernel.org>
-description: |+
- Bindings for boards with Calxeda Cortex-A9 based ECX-1000 (Highbank) SOC
- or Cortex-A15 based ECX-2000 SOCs
-
-properties:
- $nodename:
- const: '/'
- compatible:
- items:
- - enum:
- - calxeda,highbank
- - calxeda,ecx-2000
deleted file mode 100644
@@ -1,15 +0,0 @@
-Calxeda Highbank L2 cache ECC
-
-Properties:
-- compatible : Should be "calxeda,hb-sregs-l2-ecc"
-- reg : Address and size for ECC error interrupt clear registers.
-- interrupts : Should be single bit error interrupt, then double bit error
- interrupt.
-
-Example:
-
- sregs@fff3c200 {
- compatible = "calxeda,hb-sregs-l2-ecc";
- reg = <0xfff3c200 0x100>;
- interrupts = <0 71 4 0 72 4>;
- };
deleted file mode 100644
@@ -1,44 +0,0 @@
-* Calxeda AHCI SATA Controller
-
-SATA nodes are defined to describe on-chip Serial ATA controllers.
-The Calxeda SATA controller mostly conforms to the AHCI interface
-with some special extensions to add functionality.
-Each SATA controller should have its own node.
-
-Required properties:
-- compatible : compatible list, contains "calxeda,hb-ahci"
-- interrupts : <interrupt mapping for SATA IRQ>
-- reg : <registers mapping>
-
-Optional properties:
-- dma-coherent : Present if dma operations are coherent
-- calxeda,port-phys : phandle-combophy and lane assignment, which maps each
- SATA port to a combophy and a lane within that
- combophy
-- calxeda,sgpio-gpio: phandle-gpio bank, bit offset, and default on or off,
- which indicates that the driver supports SGPIO
- indicator lights using the indicated GPIOs
-- calxeda,led-order : a u32 array that map port numbers to offsets within the
- SGPIO bitstream.
-- calxeda,tx-atten : a u32 array that contains TX attenuation override
- codes, one per port. The upper 3 bytes are always
- 0 and thus ignored.
-- calxeda,pre-clocks : a u32 that indicates the number of additional clock
- cycles to transmit before sending an SGPIO pattern
-- calxeda,post-clocks: a u32 that indicates the number of additional clock
- cycles to transmit after sending an SGPIO pattern
-
-Example:
- sata@ffe08000 {
- compatible = "calxeda,hb-ahci";
- reg = <0xffe08000 0x1000>;
- interrupts = <115>;
- dma-coherent;
- calxeda,port-phys = <&combophy5 0 &combophy0 0 &combophy0 1
- &combophy0 2 &combophy0 3>;
- calxeda,sgpio-gpio =<&gpioh 5 1 &gpioh 6 1 &gpioh 7 1>;
- calxeda,led-order = <4 0 1 2 3>;
- calxeda,tx-atten = <0xff 22 0xff 0xff 23>;
- calxeda,pre-clocks = <10>;
- calxeda,post-clocks = <0>;
- };
deleted file mode 100644
@@ -1,17 +0,0 @@
-Device Tree Clock bindings for Calxeda highbank platform
-
-This binding uses the common clock binding[1].
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-
-Required properties:
-- compatible : shall be one of the following:
- "calxeda,hb-pll-clock" - for a PLL clock
- "calxeda,hb-a9periph-clock" - The A9 peripheral clock divided from the
- A9 clock.
- "calxeda,hb-a9bus-clock" - The A9 bus clock divided from the A9 clock.
- "calxeda,hb-emmc-clock" - Divided clock for MMC/SD controller.
-- reg : shall be the control register offset from SYSREGs base for the clock.
-- clocks : shall be the input parent clock phandle for the clock. This is
- either an oscillator or a pll output.
-- #clock-cells : from common clock binding; shall be set to 0.
deleted file mode 100644
@@ -1,16 +0,0 @@
-Calxeda DDR memory controller
-
-Properties:
-- compatible : Should be:
- - "calxeda,hb-ddr-ctrl" for ECX-1000
- - "calxeda,ecx-2000-ddr-ctrl" for ECX-2000
-- reg : Address and size for DDR controller registers.
-- interrupts : Interrupt for DDR controller.
-
-Example:
-
- memory-controller@fff00000 {
- compatible = "calxeda,hb-ddr-ctrl";
- reg = <0xfff00000 0x1000>;
- interrupts = <0 91 4>;
- };
deleted file mode 100644
@@ -1,18 +0,0 @@
-* Calxeda Highbank 10Gb XGMAC Ethernet
-
-Required properties:
-- compatible : Should be "calxeda,hb-xgmac"
-- reg : Address and length of the register set for the device
-- interrupts : Should contain 3 xgmac interrupts. The 1st is main interrupt.
- The 2nd is pwr mgt interrupt. The 3rd is low power state interrupt.
-
-Optional properties:
-- dma-coherent : Present if dma operations are coherent
-
-Example:
-
-ethernet@fff50000 {
- compatible = "calxeda,hb-xgmac";
- reg = <0xfff50000 0x1000>;
- interrupts = <0 77 4 0 78 4 0 79 4>;
-};
deleted file mode 100644
@@ -1,17 +0,0 @@
-Calxeda Highbank Combination Phys for SATA
-
-Properties:
-- compatible : Should be "calxeda,hb-combophy"
-- #phy-cells: Should be 1.
-- reg : Address and size for Combination Phy registers.
-- phydev: device ID for programming the combophy.
-
-Example:
-
- combophy5: combo-phy@fff5d000 {
- compatible = "calxeda,hb-combophy";
- #phy-cells = <1>;
- reg = <0xfff5d000 0x1000>;
- phydev = <31>;
- };
-
Cc: devicetree@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> --- .../devicetree/bindings/arm/calxeda.yaml | 22 ---------- .../devicetree/bindings/arm/calxeda/l2ecc.txt | 15 ------- .../devicetree/bindings/ata/sata_highbank.txt | 44 ------------------- .../devicetree/bindings/clock/calxeda.txt | 17 ------- .../memory-controllers/calxeda-ddr-ctrlr.txt | 16 ------- .../devicetree/bindings/net/calxeda-xgmac.txt | 18 -------- .../bindings/phy/calxeda-combophy.txt | 17 ------- 7 files changed, 149 deletions(-) delete mode 100644 Documentation/devicetree/bindings/arm/calxeda.yaml delete mode 100644 Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt delete mode 100644 Documentation/devicetree/bindings/ata/sata_highbank.txt delete mode 100644 Documentation/devicetree/bindings/clock/calxeda.txt delete mode 100644 Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.txt delete mode 100644 Documentation/devicetree/bindings/net/calxeda-xgmac.txt delete mode 100644 Documentation/devicetree/bindings/phy/calxeda-combophy.txt