diff mbox

fsl-diu-fb: remove check for pixel clock ranges

Message ID 1308860426-17920-1-git-send-email-timur@freescale.com (mailing list archive)
State Accepted
Commit 39785eb1d3e6c58cc8bf8f6990956a58037ecc75
Headers show

Commit Message

Timur Tabi June 23, 2011, 8:20 p.m. UTC
The Freescale DIU framebuffer driver defines two constants, MIN_PIX_CLK and
MAX_PIX_CLK, that are supposed to represent the lower and upper limits of
the pixel clock.  These values, however, are true only for one platform
clock rate (533MHz) and only for the MPC8610.  So the actual range for
the pixel clock is chip-specific, which means the current values are almost
always wrong.  The chance of an out-of-range pixel clock being used are also
remote.

Rather than try to detect an out-of-range clock in the DIU driver, we depend
on the board-specific pixel clock function (e.g. p1022ds_set_pixel_clock)
to clamp the pixel clock to a supported value.

Signed-off-by: Timur Tabi <timur@freescale.com>
---
 drivers/video/fsl-diu-fb.c |   16 ----------------
 include/linux/fsl-diu-fb.h |    6 ------
 2 files changed, 0 insertions(+), 22 deletions(-)

Comments

Paul Mundt June 24, 2011, 8:10 a.m. UTC | #1
On Thu, Jun 23, 2011 at 03:20:26PM -0500, Timur Tabi wrote:
> The Freescale DIU framebuffer driver defines two constants, MIN_PIX_CLK and
> MAX_PIX_CLK, that are supposed to represent the lower and upper limits of
> the pixel clock.  These values, however, are true only for one platform
> clock rate (533MHz) and only for the MPC8610.  So the actual range for
> the pixel clock is chip-specific, which means the current values are almost
> always wrong.  The chance of an out-of-range pixel clock being used are also
> remote.
> 
> Rather than try to detect an out-of-range clock in the DIU driver, we depend
> on the board-specific pixel clock function (e.g. p1022ds_set_pixel_clock)
> to clamp the pixel clock to a supported value.
> 
> Signed-off-by: Timur Tabi <timur@freescale.com>

Applied, thanks.
--
To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/drivers/video/fsl-diu-fb.c b/drivers/video/fsl-diu-fb.c
index bedf5be..0acc7d6 100644
--- a/drivers/video/fsl-diu-fb.c
+++ b/drivers/video/fsl-diu-fb.c
@@ -555,8 +555,6 @@  static void adjust_aoi_size_position(struct fb_var_screeninfo *var,
 static int fsl_diu_check_var(struct fb_var_screeninfo *var,
 				struct fb_info *info)
 {
-	unsigned long htotal, vtotal;
-
 	pr_debug("check_var xres: %d\n", var->xres);
 	pr_debug("check_var yres: %d\n", var->yres);
 
@@ -635,20 +633,6 @@  static int fsl_diu_check_var(struct fb_var_screeninfo *var,
 
 		break;
 	}
-	/* If the pixclock is below the minimum spec'd value then set to
-	 * refresh rate for 60Hz since this is supported by most monitors.
-	 * Refer to Documentation/fb/ for calculations.
-	 */
-	if ((var->pixclock < MIN_PIX_CLK) || (var->pixclock > MAX_PIX_CLK)) {
-		htotal = var->xres + var->right_margin + var->hsync_len +
-		    var->left_margin;
-		vtotal = var->yres + var->lower_margin + var->vsync_len +
-		    var->upper_margin;
-		var->pixclock = (vtotal * htotal * 6UL) / 100UL;
-		var->pixclock = KHZ2PICOS(var->pixclock);
-		pr_debug("pixclock set for 60Hz refresh = %u ps\n",
-			var->pixclock);
-	}
 
 	var->height = -1;
 	var->width = -1;
diff --git a/include/linux/fsl-diu-fb.h b/include/linux/fsl-diu-fb.h
index 781d467..daa9952 100644
--- a/include/linux/fsl-diu-fb.h
+++ b/include/linux/fsl-diu-fb.h
@@ -24,12 +24,6 @@ 
  * See mpc8610fb_set_par(), map_video_memory(), and unmap_video_memory()
  */
 #define MEM_ALLOC_THRESHOLD (1024*768*4+32)
-/* Minimum value that the pixel clock can be set to in pico seconds
- * This is determined by platform clock/3 where the minimum platform
- * clock is 533MHz. This gives 5629 pico seconds.
- */
-#define MIN_PIX_CLK 5629
-#define MAX_PIX_CLK 96096
 
 #include <linux/types.h>