| Message ID | 1477513801-31350-1-git-send-email-olimpiu@arcticsand.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Wed, Oct 26, 2016 at 04:30:01PM -0400, Olimpiu Dejeu wrote: > Resubmition of arcxcnn backliught driver bindings with added register > documentation > > Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com> > > --- > .../bindings/leds/backlight/arcxcnn_bl.txt | 31 ++++++++++++++++++++++ > 1 file changed, 31 insertions(+) > create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt > > diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt > new file mode 100644 > index 0000000..a7b6ff2 > --- /dev/null > +++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt > @@ -0,0 +1,31 @@ > +Binding for ArcticSand arc2c0608 LED driver > + > +Required properties: > +- compatible: should be "arc,arc2c0608" What's the correct vendor prefix? arc or arcticsand used below? > +- reg: slave address > + > +Optional properties: > +- default-brightness: brightness value on boot, value from: 0-4095 > +- label: The name of the backlight device > + See Documentation/devicetree/bindings/leds/common.txt > +- led-sources: List of enabled channels from 0 to 5. > + See Documentation/devicetree/bindings/leds/common.txt > + > +- arcticsand,led-config-0: setting for register ILED_CONFIG_0 > +- arcticsand,led-config-1: setting for register ILED_CONFIG_1 > +- arcticsand,dim-freq: PWM mode frequence setting (bits [3:0] used) > +- arcticsand,comp-config: setting for register CONFIG_COMP > +- arcticsand,filter-config: setting for register FILTER_CONFIG > +- arcticsand,trim-config: setting for register IMAXTUNE What are the default values if not present? What determines these settings? If the board design, then okay. If a an enduser wants to adjust, then they shouldn't be in DT. > + > +Example: > + > +arc2c0608@30 { > + compatible = "arc,arc2c0608"; > + reg = <0x30>; > + default-brightness = <500>; > + label = "lcd-backlight"; > + linux,default-trigger = "backlight"; > + led-sources = <0 1 2 5>; > +}; > + > -- > 2.7.4 > -- To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt new file mode 100644 index 0000000..a7b6ff2 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt @@ -0,0 +1,31 @@ +Binding for ArcticSand arc2c0608 LED driver + +Required properties: +- compatible: should be "arc,arc2c0608" +- reg: slave address + +Optional properties: +- default-brightness: brightness value on boot, value from: 0-4095 +- label: The name of the backlight device + See Documentation/devicetree/bindings/leds/common.txt +- led-sources: List of enabled channels from 0 to 5. + See Documentation/devicetree/bindings/leds/common.txt + +- arcticsand,led-config-0: setting for register ILED_CONFIG_0 +- arcticsand,led-config-1: setting for register ILED_CONFIG_1 +- arcticsand,dim-freq: PWM mode frequence setting (bits [3:0] used) +- arcticsand,comp-config: setting for register CONFIG_COMP +- arcticsand,filter-config: setting for register FILTER_CONFIG +- arcticsand,trim-config: setting for register IMAXTUNE + +Example: + +arc2c0608@30 { + compatible = "arc,arc2c0608"; + reg = <0x30>; + default-brightness = <500>; + label = "lcd-backlight"; + linux,default-trigger = "backlight"; + led-sources = <0 1 2 5>; +}; +
Resubmition of arcxcnn backliught driver bindings with added register documentation Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com> --- .../bindings/leds/backlight/arcxcnn_bl.txt | 31 ++++++++++++++++++++++ 1 file changed, 31 insertions(+) create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt