@@ -147,10 +147,48 @@
gpio-controller;
#gpio-cells = <2>;
};
+
+ camera: adv7180@21 {
+ compatible = "adi,adv7180";
+ reg = <0x21>;
+ powerdown-gpios = <&max7310_b 2 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <27 0x8>;
+ inputs = <0x00 0x02>;
+ input-names = "ADV7180 Composite on Ain1",
+ "ADV7180 Composite on Ain3";
+
+ port {
+ adv7180_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <8>;
+ };
+ };
+ };
};
};
};
+&ipu1_smfc0 {
+ fim {
+ enable = <1>;
+ };
+};
+
+&ipu1_csi0_from_ipu1_csi0_mux {
+ bus-width = <8>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+ remote-endpoint = <&adv7180_to_ipu1_csi0_mux>;
+ bus-width = <8>;
+};
+
+&ipu1_csi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+};
+
&clks {
assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
<&clks IMX6QDL_PLL4_BYPASS>,
@@ -451,6 +489,30 @@
>;
};
+ pinctrl_ipu1_csi0: ipu1grp-csi0 {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04 0x80000000
+ MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05 0x80000000
+ MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06 0x80000000
+ MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07 0x80000000
+ MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08 0x80000000
+ MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09 0x80000000
+ MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10 0x80000000
+ MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11 0x80000000
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x80000000
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x80000000
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x80000000
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x80000000
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x80000000
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x80000000
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x80000000
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x80000000
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x80000000
+ MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x80000000
+ MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x80000000
+ >;
+ };
+
pinctrl_pwm3: pwm1grp {
fsl,pins = <
MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
Enables the ADV7180 decoder sensor. The ADV7180 connects to the parallel-bus mux input on ipu1_csi0_mux. On the sabreauto, two analog video inputs are routed to the ADV7180, composite on Ain1, and composite on Ain3. Those inputs are defined via inputs and input-names under the ADV7180 node. The ADV7180 power pin is via max7310_b port expander. Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com> --- arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 62 ++++++++++++++++++++++++++++++++ 1 file changed, 62 insertions(+)