diff mbox

[v4,2/2] fpga manager: Add Xilinx slave serial SPI driver

Message ID 1488300022-30150-3-git-send-email-agust@denx.de (mailing list archive)
State Accepted, archived
Headers show

Commit Message

Anatolij Gustschin Feb. 28, 2017, 4:40 p.m. UTC 
The driver loads FPGA firmware over SPI, using the "slave serial"
configuration interface on Xilinx FPGAs.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
---
This patch requires patch https://lkml.org/lkml/2017/2/15/667
for building

Changes in v4:

 - increase program latency up to 7.5ms for other Xilinx FPGAs
 - continue to apply CCLK cycles until specified timeout elapses (to
   cover more possible configuration DONE scenarios)
 - apply 8 CCLK cycles afer DONE signal
 - rebased to apply on top of Kconfig/Makefile changes by queued
   fpga manager patches

Changes in v3:

 - use named constant for udelay()/usleep_range() arguments
 - drop not needed .owner init
 - correct module licence (GPL v2)
 - fix build warning with newer gcc (in min() macro)

Changes in v2:

 - rebased on v4.10

 drivers/fpga/Kconfig      |   7 ++
 drivers/fpga/Makefile     |   1 +
 drivers/fpga/xilinx-spi.c | 198 ++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 206 insertions(+)
 create mode 100644 drivers/fpga/xilinx-spi.c

Comments

Michal Simek March 16, 2017, 11:01 a.m. UTC | #1 
On 28.2.2017 17:40, Anatolij Gustschin wrote:
> The driver loads FPGA firmware over SPI, using the "slave serial"
> configuration interface on Xilinx FPGAs.
> 
> Signed-off-by: Anatolij Gustschin <agust@denx.de>
> ---
> This patch requires patch https://lkml.org/lkml/2017/2/15/667
> for building
> 
> Changes in v4:
> 
>  - increase program latency up to 7.5ms for other Xilinx FPGAs
>  - continue to apply CCLK cycles until specified timeout elapses (to
>    cover more possible configuration DONE scenarios)
>  - apply 8 CCLK cycles afer DONE signal
>  - rebased to apply on top of Kconfig/Makefile changes by queued
>    fpga manager patches
> 
> Changes in v3:
> 
>  - use named constant for udelay()/usleep_range() arguments
>  - drop not needed .owner init
>  - correct module licence (GPL v2)
>  - fix build warning with newer gcc (in min() macro)
> 
> Changes in v2:
> 
>  - rebased on v4.10
> 
>  drivers/fpga/Kconfig      |   7 ++
>  drivers/fpga/Makefile     |   1 +
>  drivers/fpga/xilinx-spi.c | 198 ++++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 206 insertions(+)
>  create mode 100644 drivers/fpga/xilinx-spi.c
> 
> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
> index dee470f..c81cb7d 100644
> --- a/drivers/fpga/Kconfig
> +++ b/drivers/fpga/Kconfig
> @@ -46,6 +46,13 @@ config FPGA_MGR_TS73XX
>  	  FPGA manager driver support for the Altera Cyclone II FPGA
>  	  present on the TS-73xx SBC boards.
>  
> +config FPGA_MGR_XILINX_SPI
> +	tristate "Xilinx Configuration over Slave Serial (SPI)"
> +	depends on SPI
> +	help
> +	  FPGA manager driver support for Xilinx FPGA configuration
> +	  over slave serial interface.
> +
>  config FPGA_MGR_ZYNQ_FPGA
>  	tristate "Xilinx Zynq FPGA"
>  	depends on ARCH_ZYNQ || COMPILE_TEST
> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
> index a5ee3ff..c6f5d74 100644
> --- a/drivers/fpga/Makefile
> +++ b/drivers/fpga/Makefile
> @@ -10,6 +10,7 @@ obj-$(CONFIG_FPGA_MGR_ICE40_SPI)	+= ice40-spi.o
>  obj-$(CONFIG_FPGA_MGR_SOCFPGA)		+= socfpga.o
>  obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10)	+= socfpga-a10.o
>  obj-$(CONFIG_FPGA_MGR_TS73XX)		+= ts73xx-fpga.o
> +obj-$(CONFIG_FPGA_MGR_XILINX_SPI)	+= xilinx-spi.o
>  obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)	+= zynq-fpga.o
>  
>  # FPGA Bridge Drivers
> diff --git a/drivers/fpga/xilinx-spi.c b/drivers/fpga/xilinx-spi.c
> new file mode 100644
> index 0000000..9b62a4c
> --- /dev/null
> +++ b/drivers/fpga/xilinx-spi.c
> @@ -0,0 +1,198 @@
> +/*
> + * Xilinx Spartan6 Slave Serial SPI Driver
> + *
> + * Copyright (C) 2017 DENX Software Engineering
> + *
> + * Anatolij Gustschin <agust@denx.de>
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> + *
> + * Manage Xilinx FPGA firmware that is loaded over SPI using
> + * the slave serial configuration interface.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/fpga/fpga-mgr.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/module.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/of.h>
> +#include <linux/spi/spi.h>
> +#include <linux/sizes.h>
> +
> +struct xilinx_spi_conf {
> +	struct spi_device *spi;
> +	struct gpio_desc *prog_b;
> +	struct gpio_desc *done;
> +};
> +
> +static enum fpga_mgr_states xilinx_spi_state(struct fpga_manager *mgr)
> +{
> +	struct xilinx_spi_conf *conf = mgr->priv;
> +
> +	if (!gpiod_get_value(conf->done))
> +		return FPGA_MGR_STATE_RESET;
> +
> +	return FPGA_MGR_STATE_UNKNOWN;
> +}
> +
> +static int xilinx_spi_write_init(struct fpga_manager *mgr,
> +				 struct fpga_image_info *info,
> +				 const char *buf, size_t count)
> +{
> +	struct xilinx_spi_conf *conf = mgr->priv;
> +	const size_t prog_latency_7500us = 7500;
> +	const size_t prog_pulse_1us = 1;
> +
> +	if (info->flags & FPGA_MGR_PARTIAL_RECONFIG) {
> +		dev_err(&mgr->dev, "Partial reconfiguration not supported.\n");
> +		return -EINVAL;
> +	}
> +
> +	gpiod_set_value(conf->prog_b, 1);
> +
> +	udelay(prog_pulse_1us); /* min is 500 ns */
> +
> +	gpiod_set_value(conf->prog_b, 0);
> +
> +	if (gpiod_get_value(conf->done)) {
> +		dev_err(&mgr->dev, "Unexpected DONE pin state...\n");
> +		return -EIO;
> +	}
> +
> +	/* program latency */
> +	usleep_range(prog_latency_7500us, prog_latency_7500us + 100);
> +	return 0;
> +}
> +
> +static int xilinx_spi_write(struct fpga_manager *mgr, const char *buf,
> +			    size_t count)
> +{
> +	struct xilinx_spi_conf *conf = mgr->priv;
> +	const char *fw_data = buf;
> +	const char *fw_data_end = fw_data + count;
> +
> +	while (fw_data < fw_data_end) {
> +		size_t remaining, stride;
> +		int ret;
> +
> +		remaining = fw_data_end - fw_data;
> +		stride = min_t(size_t, remaining, SZ_4K);
> +
> +		ret = spi_write(conf->spi, fw_data, stride);
> +		if (ret) {
> +			dev_err(&mgr->dev, "SPI error in firmware write: %d\n",
> +				ret);
> +			return ret;
> +		}
> +		fw_data += stride;
> +	}
> +
> +	return 0;
> +}
> +
> +static int xilinx_spi_apply_cclk_cycles(struct xilinx_spi_conf *conf)
> +{
> +	struct spi_device *spi = conf->spi;
> +	const u8 din_data[1] = { 0xff };
> +	int ret;
> +
> +	ret = spi_write(conf->spi, din_data, sizeof(din_data));
> +	if (ret)
> +		dev_err(&spi->dev, "applying CCLK cycles failed: %d\n", ret);
> +
> +	return ret;
> +}
> +
> +static int xilinx_spi_write_complete(struct fpga_manager *mgr,
> +				     struct fpga_image_info *info)
> +{
> +	struct xilinx_spi_conf *conf = mgr->priv;
> +	unsigned long timeout;
> +	int ret;
> +
> +	if (gpiod_get_value(conf->done))
> +		return xilinx_spi_apply_cclk_cycles(conf);
> +
> +	timeout = jiffies + usecs_to_jiffies(info->config_complete_timeout_us);
> +
> +	while (time_before(jiffies, timeout)) {
> +
> +		ret = xilinx_spi_apply_cclk_cycles(conf);
> +		if (ret)
> +			return ret;
> +
> +		if (gpiod_get_value(conf->done))
> +			return xilinx_spi_apply_cclk_cycles(conf);
> +	}
> +
> +	dev_err(&mgr->dev, "Timeout after config data transfer.\n");
> +	return -ETIMEDOUT;
> +}
> +
> +static const struct fpga_manager_ops xilinx_spi_ops = {
> +	.state = xilinx_spi_state,
> +	.write_init = xilinx_spi_write_init,
> +	.write = xilinx_spi_write,
> +	.write_complete = xilinx_spi_write_complete,
> +};
> +
> +static int xilinx_spi_probe(struct spi_device *spi)
> +{
> +	struct xilinx_spi_conf *conf;
> +
> +	conf = devm_kzalloc(&spi->dev, sizeof(*conf), GFP_KERNEL);
> +	if (!conf)
> +		return -ENOMEM;
> +
> +	conf->spi = spi;
> +
> +	/* PROGRAM_B is active low */
> +	conf->prog_b = devm_gpiod_get(&spi->dev, "prog_b", GPIOD_OUT_LOW);
> +	if (IS_ERR(conf->prog_b)) {
> +		dev_err(&spi->dev, "Failed to get PROGRAM_B gpio: %ld\n",
> +			PTR_ERR(conf->prog_b));
> +		return PTR_ERR(conf->prog_b);
> +	}
> +
> +	conf->done = devm_gpiod_get(&spi->dev, "done", GPIOD_IN);
> +	if (IS_ERR(conf->done)) {
> +		dev_err(&spi->dev, "Failed to get DONE gpio: %ld\n",
> +			PTR_ERR(conf->done));
> +		return PTR_ERR(conf->done);
> +	}
> +
> +	return fpga_mgr_register(&spi->dev, "Xilinx Slave Serial FPGA Manager",
> +				 &xilinx_spi_ops, conf);
> +}
> +
> +static int xilinx_spi_remove(struct spi_device *spi)
> +{
> +	fpga_mgr_unregister(&spi->dev);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id xlnx_spi_of_match[] = {
> +	{ .compatible = "xlnx,fpga-slave-serial", },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, xlnx_spi_of_match);
> +
> +static struct spi_driver xilinx_slave_spi_driver = {
> +	.driver = {
> +		.name = "xlnx-slave-spi",
> +		.of_match_table = of_match_ptr(xlnx_spi_of_match),
> +	},
> +	.probe = xilinx_spi_probe,
> +	.remove = xilinx_spi_remove,
> +};
> +
> +module_spi_driver(xilinx_slave_spi_driver)
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_AUTHOR("Anatolij Gustschin <agust@denx.de>");
> +MODULE_DESCRIPTION("Load Xilinx FPGA firmware over SPI");
> 

Acked-by: Michal Simek <michal.simek@xilinx.com>

Thanks,
Michal
Moritz Fischer March 16, 2017, 2:58 p.m. UTC | #2 
On Tue, Feb 28, 2017 at 8:40 AM, Anatolij Gustschin <agust@denx.de> wrote:
> The driver loads FPGA firmware over SPI, using the "slave serial"
> configuration interface on Xilinx FPGAs.
>
> Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
> ---
> This patch requires patch https://lkml.org/lkml/2017/2/15/667
> for building
>
> Changes in v4:
>
>  - increase program latency up to 7.5ms for other Xilinx FPGAs
>  - continue to apply CCLK cycles until specified timeout elapses (to
>    cover more possible configuration DONE scenarios)
>  - apply 8 CCLK cycles afer DONE signal
>  - rebased to apply on top of Kconfig/Makefile changes by queued
>    fpga manager patches
>
> Changes in v3:
>
>  - use named constant for udelay()/usleep_range() arguments
>  - drop not needed .owner init
>  - correct module licence (GPL v2)
>  - fix build warning with newer gcc (in min() macro)
>
> Changes in v2:
>
>  - rebased on v4.10
>
>  drivers/fpga/Kconfig      |   7 ++
>  drivers/fpga/Makefile     |   1 +
>  drivers/fpga/xilinx-spi.c | 198 ++++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 206 insertions(+)
>  create mode 100644 drivers/fpga/xilinx-spi.c
>
> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
> index dee470f..c81cb7d 100644
> --- a/drivers/fpga/Kconfig
> +++ b/drivers/fpga/Kconfig
> @@ -46,6 +46,13 @@ config FPGA_MGR_TS73XX
>           FPGA manager driver support for the Altera Cyclone II FPGA
>           present on the TS-73xx SBC boards.
>
> +config FPGA_MGR_XILINX_SPI
> +       tristate "Xilinx Configuration over Slave Serial (SPI)"
> +       depends on SPI
> +       help
> +         FPGA manager driver support for Xilinx FPGA configuration
> +         over slave serial interface.
> +
>  config FPGA_MGR_ZYNQ_FPGA
>         tristate "Xilinx Zynq FPGA"
>         depends on ARCH_ZYNQ || COMPILE_TEST
> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
> index a5ee3ff..c6f5d74 100644
> --- a/drivers/fpga/Makefile
> +++ b/drivers/fpga/Makefile
> @@ -10,6 +10,7 @@ obj-$(CONFIG_FPGA_MGR_ICE40_SPI)      += ice40-spi.o
>  obj-$(CONFIG_FPGA_MGR_SOCFPGA)         += socfpga.o
>  obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10)     += socfpga-a10.o
>  obj-$(CONFIG_FPGA_MGR_TS73XX)          += ts73xx-fpga.o
> +obj-$(CONFIG_FPGA_MGR_XILINX_SPI)      += xilinx-spi.o
>  obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)       += zynq-fpga.o
>
>  # FPGA Bridge Drivers
> diff --git a/drivers/fpga/xilinx-spi.c b/drivers/fpga/xilinx-spi.c
> new file mode 100644
> index 0000000..9b62a4c
> --- /dev/null
> +++ b/drivers/fpga/xilinx-spi.c
> @@ -0,0 +1,198 @@
> +/*
> + * Xilinx Spartan6 Slave Serial SPI Driver
> + *
> + * Copyright (C) 2017 DENX Software Engineering
> + *
> + * Anatolij Gustschin <agust@denx.de>
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> + *
> + * Manage Xilinx FPGA firmware that is loaded over SPI using
> + * the slave serial configuration interface.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/fpga/fpga-mgr.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/module.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/of.h>
> +#include <linux/spi/spi.h>
> +#include <linux/sizes.h>
> +
> +struct xilinx_spi_conf {
> +       struct spi_device *spi;
> +       struct gpio_desc *prog_b;
> +       struct gpio_desc *done;
> +};
> +
> +static enum fpga_mgr_states xilinx_spi_state(struct fpga_manager *mgr)
> +{
> +       struct xilinx_spi_conf *conf = mgr->priv;
> +
> +       if (!gpiod_get_value(conf->done))
> +               return FPGA_MGR_STATE_RESET;
> +
> +       return FPGA_MGR_STATE_UNKNOWN;
> +}
> +
> +static int xilinx_spi_write_init(struct fpga_manager *mgr,
> +                                struct fpga_image_info *info,
> +                                const char *buf, size_t count)
> +{
> +       struct xilinx_spi_conf *conf = mgr->priv;
> +       const size_t prog_latency_7500us = 7500;
> +       const size_t prog_pulse_1us = 1;
> +
> +       if (info->flags & FPGA_MGR_PARTIAL_RECONFIG) {
> +               dev_err(&mgr->dev, "Partial reconfiguration not supported.\n");
> +               return -EINVAL;
> +       }
> +
> +       gpiod_set_value(conf->prog_b, 1);
> +
> +       udelay(prog_pulse_1us); /* min is 500 ns */
> +
> +       gpiod_set_value(conf->prog_b, 0);
> +
> +       if (gpiod_get_value(conf->done)) {
> +               dev_err(&mgr->dev, "Unexpected DONE pin state...\n");
> +               return -EIO;
> +       }
> +
> +       /* program latency */
> +       usleep_range(prog_latency_7500us, prog_latency_7500us + 100);
> +       return 0;
> +}
> +
> +static int xilinx_spi_write(struct fpga_manager *mgr, const char *buf,
> +                           size_t count)
> +{
> +       struct xilinx_spi_conf *conf = mgr->priv;
> +       const char *fw_data = buf;
> +       const char *fw_data_end = fw_data + count;
> +
> +       while (fw_data < fw_data_end) {
> +               size_t remaining, stride;
> +               int ret;
> +
> +               remaining = fw_data_end - fw_data;
> +               stride = min_t(size_t, remaining, SZ_4K);
> +
> +               ret = spi_write(conf->spi, fw_data, stride);
> +               if (ret) {
> +                       dev_err(&mgr->dev, "SPI error in firmware write: %d\n",
> +                               ret);
> +                       return ret;
> +               }
> +               fw_data += stride;
> +       }
> +
> +       return 0;
> +}
> +
> +static int xilinx_spi_apply_cclk_cycles(struct xilinx_spi_conf *conf)
> +{
> +       struct spi_device *spi = conf->spi;
> +       const u8 din_data[1] = { 0xff };
> +       int ret;
> +
> +       ret = spi_write(conf->spi, din_data, sizeof(din_data));
> +       if (ret)
> +               dev_err(&spi->dev, "applying CCLK cycles failed: %d\n", ret);
> +
> +       return ret;
> +}
> +
> +static int xilinx_spi_write_complete(struct fpga_manager *mgr,
> +                                    struct fpga_image_info *info)
> +{
> +       struct xilinx_spi_conf *conf = mgr->priv;
> +       unsigned long timeout;
> +       int ret;
> +
> +       if (gpiod_get_value(conf->done))
> +               return xilinx_spi_apply_cclk_cycles(conf);
> +
> +       timeout = jiffies + usecs_to_jiffies(info->config_complete_timeout_us);
> +
> +       while (time_before(jiffies, timeout)) {
> +
> +               ret = xilinx_spi_apply_cclk_cycles(conf);
> +               if (ret)
> +                       return ret;
> +
> +               if (gpiod_get_value(conf->done))
> +                       return xilinx_spi_apply_cclk_cycles(conf);
> +       }
> +
> +       dev_err(&mgr->dev, "Timeout after config data transfer.\n");
> +       return -ETIMEDOUT;
> +}
> +
> +static const struct fpga_manager_ops xilinx_spi_ops = {
> +       .state = xilinx_spi_state,
> +       .write_init = xilinx_spi_write_init,
> +       .write = xilinx_spi_write,
> +       .write_complete = xilinx_spi_write_complete,
> +};
> +
> +static int xilinx_spi_probe(struct spi_device *spi)
> +{
> +       struct xilinx_spi_conf *conf;
> +
> +       conf = devm_kzalloc(&spi->dev, sizeof(*conf), GFP_KERNEL);
> +       if (!conf)
> +               return -ENOMEM;
> +
> +       conf->spi = spi;
> +
> +       /* PROGRAM_B is active low */
> +       conf->prog_b = devm_gpiod_get(&spi->dev, "prog_b", GPIOD_OUT_LOW);
> +       if (IS_ERR(conf->prog_b)) {
> +               dev_err(&spi->dev, "Failed to get PROGRAM_B gpio: %ld\n",
> +                       PTR_ERR(conf->prog_b));
> +               return PTR_ERR(conf->prog_b);
> +       }
> +
> +       conf->done = devm_gpiod_get(&spi->dev, "done", GPIOD_IN);
> +       if (IS_ERR(conf->done)) {
> +               dev_err(&spi->dev, "Failed to get DONE gpio: %ld\n",
> +                       PTR_ERR(conf->done));
> +               return PTR_ERR(conf->done);
> +       }
> +
> +       return fpga_mgr_register(&spi->dev, "Xilinx Slave Serial FPGA Manager",
> +                                &xilinx_spi_ops, conf);
> +}
> +
> +static int xilinx_spi_remove(struct spi_device *spi)
> +{
> +       fpga_mgr_unregister(&spi->dev);
> +
> +       return 0;
> +}
> +
> +static const struct of_device_id xlnx_spi_of_match[] = {
> +       { .compatible = "xlnx,fpga-slave-serial", },
> +       {}
> +};
> +MODULE_DEVICE_TABLE(of, xlnx_spi_of_match);
> +
> +static struct spi_driver xilinx_slave_spi_driver = {
> +       .driver = {
> +               .name = "xlnx-slave-spi",
> +               .of_match_table = of_match_ptr(xlnx_spi_of_match),
> +       },
> +       .probe = xilinx_spi_probe,
> +       .remove = xilinx_spi_remove,
> +};
> +
> +module_spi_driver(xilinx_slave_spi_driver)
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_AUTHOR("Anatolij Gustschin <agust@denx.de>");
> +MODULE_DESCRIPTION("Load Xilinx FPGA firmware over SPI");
> --
> 2.7.4
>
--
To unsubscribe from this list: send the line "unsubscribe linux-fpga" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Alan Tull March 23, 2017, 11:51 p.m. UTC | #3 
On Thu, Mar 16, 2017 at 9:58 AM, Moritz Fischer <mdf@kernel.org> wrote:
> On Tue, Feb 28, 2017 at 8:40 AM, Anatolij Gustschin <agust@denx.de> wrote:
>> The driver loads FPGA firmware over SPI, using the "slave serial"
>> configuration interface on Xilinx FPGAs.
>>
>> Signed-off-by: Anatolij Gustschin <agust@denx.de>
> Reviewed-by: Moritz Fischer <mdf@kernel.org>

Acked-by: Alan Tull <atull@kernel.org>
--
To unsubscribe from this list: send the line "unsubscribe linux-fpga" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
index dee470f..c81cb7d 100644
--- a/drivers/fpga/Kconfig
+++ b/drivers/fpga/Kconfig
@@ -46,6 +46,13 @@  config FPGA_MGR_TS73XX
 	  FPGA manager driver support for the Altera Cyclone II FPGA
 	  present on the TS-73xx SBC boards.
 
+config FPGA_MGR_XILINX_SPI
+	tristate "Xilinx Configuration over Slave Serial (SPI)"
+	depends on SPI
+	help
+	  FPGA manager driver support for Xilinx FPGA configuration
+	  over slave serial interface.
+
 config FPGA_MGR_ZYNQ_FPGA
 	tristate "Xilinx Zynq FPGA"
 	depends on ARCH_ZYNQ || COMPILE_TEST
diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
index a5ee3ff..c6f5d74 100644
--- a/drivers/fpga/Makefile
+++ b/drivers/fpga/Makefile
@@ -10,6 +10,7 @@  obj-$(CONFIG_FPGA_MGR_ICE40_SPI)	+= ice40-spi.o
 obj-$(CONFIG_FPGA_MGR_SOCFPGA)		+= socfpga.o
 obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10)	+= socfpga-a10.o
 obj-$(CONFIG_FPGA_MGR_TS73XX)		+= ts73xx-fpga.o
+obj-$(CONFIG_FPGA_MGR_XILINX_SPI)	+= xilinx-spi.o
 obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)	+= zynq-fpga.o
 
 # FPGA Bridge Drivers
diff --git a/drivers/fpga/xilinx-spi.c b/drivers/fpga/xilinx-spi.c
new file mode 100644
index 0000000..9b62a4c
--- /dev/null
+++ b/drivers/fpga/xilinx-spi.c
@@ -0,0 +1,198 @@ 
+/*
+ * Xilinx Spartan6 Slave Serial SPI Driver
+ *
+ * Copyright (C) 2017 DENX Software Engineering
+ *
+ * Anatolij Gustschin <agust@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * Manage Xilinx FPGA firmware that is loaded over SPI using
+ * the slave serial configuration interface.
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/fpga/fpga-mgr.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/of.h>
+#include <linux/spi/spi.h>
+#include <linux/sizes.h>
+
+struct xilinx_spi_conf {
+	struct spi_device *spi;
+	struct gpio_desc *prog_b;
+	struct gpio_desc *done;
+};
+
+static enum fpga_mgr_states xilinx_spi_state(struct fpga_manager *mgr)
+{
+	struct xilinx_spi_conf *conf = mgr->priv;
+
+	if (!gpiod_get_value(conf->done))
+		return FPGA_MGR_STATE_RESET;
+
+	return FPGA_MGR_STATE_UNKNOWN;
+}
+
+static int xilinx_spi_write_init(struct fpga_manager *mgr,
+				 struct fpga_image_info *info,
+				 const char *buf, size_t count)
+{
+	struct xilinx_spi_conf *conf = mgr->priv;
+	const size_t prog_latency_7500us = 7500;
+	const size_t prog_pulse_1us = 1;
+
+	if (info->flags & FPGA_MGR_PARTIAL_RECONFIG) {
+		dev_err(&mgr->dev, "Partial reconfiguration not supported.\n");
+		return -EINVAL;
+	}
+
+	gpiod_set_value(conf->prog_b, 1);
+
+	udelay(prog_pulse_1us); /* min is 500 ns */
+
+	gpiod_set_value(conf->prog_b, 0);
+
+	if (gpiod_get_value(conf->done)) {
+		dev_err(&mgr->dev, "Unexpected DONE pin state...\n");
+		return -EIO;
+	}
+
+	/* program latency */
+	usleep_range(prog_latency_7500us, prog_latency_7500us + 100);
+	return 0;
+}
+
+static int xilinx_spi_write(struct fpga_manager *mgr, const char *buf,
+			    size_t count)
+{
+	struct xilinx_spi_conf *conf = mgr->priv;
+	const char *fw_data = buf;
+	const char *fw_data_end = fw_data + count;
+
+	while (fw_data < fw_data_end) {
+		size_t remaining, stride;
+		int ret;
+
+		remaining = fw_data_end - fw_data;
+		stride = min_t(size_t, remaining, SZ_4K);
+
+		ret = spi_write(conf->spi, fw_data, stride);
+		if (ret) {
+			dev_err(&mgr->dev, "SPI error in firmware write: %d\n",
+				ret);
+			return ret;
+		}
+		fw_data += stride;
+	}
+
+	return 0;
+}
+
+static int xilinx_spi_apply_cclk_cycles(struct xilinx_spi_conf *conf)
+{
+	struct spi_device *spi = conf->spi;
+	const u8 din_data[1] = { 0xff };
+	int ret;
+
+	ret = spi_write(conf->spi, din_data, sizeof(din_data));
+	if (ret)
+		dev_err(&spi->dev, "applying CCLK cycles failed: %d\n", ret);
+
+	return ret;
+}
+
+static int xilinx_spi_write_complete(struct fpga_manager *mgr,
+				     struct fpga_image_info *info)
+{
+	struct xilinx_spi_conf *conf = mgr->priv;
+	unsigned long timeout;
+	int ret;
+
+	if (gpiod_get_value(conf->done))
+		return xilinx_spi_apply_cclk_cycles(conf);
+
+	timeout = jiffies + usecs_to_jiffies(info->config_complete_timeout_us);
+
+	while (time_before(jiffies, timeout)) {
+
+		ret = xilinx_spi_apply_cclk_cycles(conf);
+		if (ret)
+			return ret;
+
+		if (gpiod_get_value(conf->done))
+			return xilinx_spi_apply_cclk_cycles(conf);
+	}
+
+	dev_err(&mgr->dev, "Timeout after config data transfer.\n");
+	return -ETIMEDOUT;
+}
+
+static const struct fpga_manager_ops xilinx_spi_ops = {
+	.state = xilinx_spi_state,
+	.write_init = xilinx_spi_write_init,
+	.write = xilinx_spi_write,
+	.write_complete = xilinx_spi_write_complete,
+};
+
+static int xilinx_spi_probe(struct spi_device *spi)
+{
+	struct xilinx_spi_conf *conf;
+
+	conf = devm_kzalloc(&spi->dev, sizeof(*conf), GFP_KERNEL);
+	if (!conf)
+		return -ENOMEM;
+
+	conf->spi = spi;
+
+	/* PROGRAM_B is active low */
+	conf->prog_b = devm_gpiod_get(&spi->dev, "prog_b", GPIOD_OUT_LOW);
+	if (IS_ERR(conf->prog_b)) {
+		dev_err(&spi->dev, "Failed to get PROGRAM_B gpio: %ld\n",
+			PTR_ERR(conf->prog_b));
+		return PTR_ERR(conf->prog_b);
+	}
+
+	conf->done = devm_gpiod_get(&spi->dev, "done", GPIOD_IN);
+	if (IS_ERR(conf->done)) {
+		dev_err(&spi->dev, "Failed to get DONE gpio: %ld\n",
+			PTR_ERR(conf->done));
+		return PTR_ERR(conf->done);
+	}
+
+	return fpga_mgr_register(&spi->dev, "Xilinx Slave Serial FPGA Manager",
+				 &xilinx_spi_ops, conf);
+}
+
+static int xilinx_spi_remove(struct spi_device *spi)
+{
+	fpga_mgr_unregister(&spi->dev);
+
+	return 0;
+}
+
+static const struct of_device_id xlnx_spi_of_match[] = {
+	{ .compatible = "xlnx,fpga-slave-serial", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, xlnx_spi_of_match);
+
+static struct spi_driver xilinx_slave_spi_driver = {
+	.driver = {
+		.name = "xlnx-slave-spi",
+		.of_match_table = of_match_ptr(xlnx_spi_of_match),
+	},
+	.probe = xilinx_spi_probe,
+	.remove = xilinx_spi_remove,
+};
+
+module_spi_driver(xilinx_slave_spi_driver)
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Anatolij Gustschin <agust@denx.de>");
+MODULE_DESCRIPTION("Load Xilinx FPGA firmware over SPI");