diff mbox series

[RESEND,v5,7/8] arm64: dts: Add DTS for Marvell PXA1908 and samsung,coreprimevelte

Message ID 20230929-pxa1908-lkml-v5-7-5aa5a1109c5f@skole.hr (mailing list archive)
State Superseded
Headers show
Series Initial Marvell PXA1908 support | expand

Commit Message

Duje Mihanović Sept. 29, 2023, 3:42 p.m. UTC
Add DTS for Marvell PXA1908 SoC and Samsung Galaxy Core Prime Value
Edition LTE, a smartphone based on said SoC.

Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
 arch/arm64/boot/dts/marvell/Makefile               |   3 +
 .../dts/marvell/pxa1908-samsung-coreprimevelte.dts | 333 +++++++++++++++++++++
 arch/arm64/boot/dts/marvell/pxa1908.dtsi           | 295 ++++++++++++++++++
 3 files changed, 631 insertions(+)

Comments

Linus Walleij Sept. 29, 2023, 10:05 p.m. UTC | #1
On Fri, Sep 29, 2023 at 5:42 PM Duje Mihanović <duje.mihanovic@skole.hr> wrote:

> Add DTS for Marvell PXA1908 SoC and Samsung Galaxy Core Prime Value
> Edition LTE, a smartphone based on said SoC.
>
> Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
(...)

> +&pmx {
> +       pinctrl-single,gpio-range = <&range 55 55 0>,
> +                                   <&range 110 32 0>,
> +                                   <&range 52 1 0>;
> +
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&board_pins_1 &board_pins_2 &board_pins_3>;
> +
> +       board_pins_1: pinmux-board-1 {
> +               pinctrl-single,pins = <
> +                       0x160 0
> +                       0x164 0
> +                       0x168 0
> +                       0x16c 0
> +               >;
> +               pinctrl-single,drive-strength = <0x1000 0x1800>;
> +               pinctrl-single,bias-pullup = <0x8000 0x8000 0 0xc000>;
> +               pinctrl-single,bias-pulldown = <0x8000 0x8000 0 0xa000>;
> +               pinctrl-single,input-schmitt = <0 0x30>;
> +               pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
> +               pinctrl-single,low-power-mode = <0x288 0x388>;
> +       };
(...)
> +                       pmx: pinmux@1e000 {
> +                               compatible = "pinconf-single";

At least add a new binding for "marvell,pxa1908-padconf"
and use that like this:

compatible = "marvell,pxa1908-padconf", "pinconf-single";

When you use pinctrl-single you get the slightly opaque device
trees as seen above, so it's not something I'd recommend, I'd
rather write my own pin controller.

But it exists, so I can't say you can't use it. Not my choice.
I understand it is convenient.

It is possible to switch later, but only if you have a unique
pin controller compatible so please add that.

Yours,
Linus Walleij
Duje Mihanović Sept. 30, 2023, 8:25 a.m. UTC | #2
On Saturday, September 30, 2023 12:05:41 AM CEST Linus Walleij wrote:
> But it exists, so I can't say you can't use it. Not my choice.
> I understand it is convenient.
> 
> It is possible to switch later, but only if you have a unique
> pin controller compatible so please add that.

Maybe a dumb question. I might want to do this at some point to clean up the 
device tree a bit, are there any such pinctrl drivers I can use as a 
reference?

Regards,
Duje
Linus Walleij Sept. 30, 2023, 3:37 p.m. UTC | #3
On Sat, Sep 30, 2023 at 10:25 AM Duje Mihanović <duje.mihanovic@skole.hr> wrote:
> On Saturday, September 30, 2023 12:05:41 AM CEST Linus Walleij wrote:
> > But it exists, so I can't say you can't use it. Not my choice.
> > I understand it is convenient.
> >
> > It is possible to switch later, but only if you have a unique
> > pin controller compatible so please add that.
>
> Maybe a dumb question. I might want to do this at some point to clean up the
> device tree a bit, are there any such pinctrl drivers I can use as a
> reference?

Since it's Marvell after all (albeit a descendant of the 20 yo
PXA platform!) I would expect new Marvell SoCs to be more alike
the AC5 bindings that Chris Packham merged only last year:
Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml
Driver:
drivers/pinctrl/mvebu/pinctrl-armada-xp.c
drivers/pinctrl/mvebu/pinctrl-mvebu.c

But if this pin controller is more related to PXA (Intel) hardware
than to either Kirkwood or Armada, you might want to do something
entirely different. It depends a bit on hardware.

Hardware such as pinctrl-single.c with one mux configuration
register per pin usually follow the Qualcomm way of doing
things, which is to simply have one group per pin, then that
can be associated with desired functions:
Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml
this has the upside of using all the standard bindings for
bias etc. Driver:
drivers/pinctrl/qcom/pinctrl-msm.c
then qualcomm have subdrivers for each SoC calling into this
so you have to check "real" bindings and drivers such as:
Documentation/devicetree/bindings/pinctrl/qcom,sm8550-tlmm.yaml
drivers/pinctrl/qcom/pinctrl-sm8550.c

Yours,
Linus Walleij
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 79ac09b58a89..263be6ec7567 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -27,3 +27,6 @@  dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += ac5-98dx35xx-rd.dtb
+
+# MMP SoC Family
+dtb-$(CONFIG_ARCH_MMP) += pxa1908-samsung-coreprimevelte.dtb
diff --git a/arch/arm64/boot/dts/marvell/pxa1908-samsung-coreprimevelte.dts b/arch/arm64/boot/dts/marvell/pxa1908-samsung-coreprimevelte.dts
new file mode 100644
index 000000000000..e3c863d517a8
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/pxa1908-samsung-coreprimevelte.dts
@@ -0,0 +1,333 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+#include "pxa1908.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+	model = "Samsung Galaxy Core Prime VE LTE";
+	compatible = "samsung,coreprimevelte", "marvell,pxa1908";
+
+	aliases {
+		mmc0 = &sdh2; /* eMMC */
+		mmc1 = &sdh0; /* SD card */
+		serial0 = &uart0;
+	};
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		stdout-path = "serial0:115200n8";
+
+		fb0: framebuffer@17177000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0x17177000 0 (480 * 800 * 4)>;
+			width = <480>;
+			height = <800>;
+			stride = <(480 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	/* Bootloader fills this in */
+	memory {
+		device_type = "memory";
+		reg = <0 0 0 0>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer@17000000 {
+			reg = <0 0x17000000 0 0x1800000>;
+			no-map;
+		};
+
+		gpu@9000000 {
+			reg = <0 0x9000000 0 0x1000000>;
+		};
+
+		/* Communications processor, aka modem */
+		cp@3000000 {
+			reg = <0 0x3000000 0 0x5000000>;
+		};
+
+		cm3@a000000 {
+			reg = <0 0xa000000 0 0x80000>;
+		};
+
+		seclog@8000000 {
+			reg = <0 0x8000000 0 0x100000>;
+		};
+
+		ramoops@8100000 {
+			compatible = "ramoops";
+			reg = <0 0x8100000 0 0x40000>;
+			record-size = <0x8000>;
+			console-size = <0x20000>;
+			max-reason = <5>;
+		};
+	};
+
+
+	i2c-muic {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio 30 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio 29 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <3>;
+		i2c-gpio,timeout-ms = <100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_muic_pins>;
+
+		muic: extcon@14 {
+			compatible = "siliconmitus,sm5504-muic";
+			reg = <0x14>;
+			interrupt-parent = <&gpio>;
+			interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pins>;
+		autorepeat;
+
+		key-home {
+			label = "Home";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpio 50 GPIO_ACTIVE_LOW>;
+		};
+
+		key-volup {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+		};
+
+		key-voldown {
+			label = "Volume Down";
+			linux,code = <KEY_VOLUMEDOWN>;
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&smmu {
+	status = "okay";
+};
+
+&pmx {
+	pinctrl-single,gpio-range = <&range 55 55 0>,
+				    <&range 110 32 0>,
+				    <&range 52 1 0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&board_pins_1 &board_pins_2 &board_pins_3>;
+
+	board_pins_1: pinmux-board-1 {
+		pinctrl-single,pins = <
+			0x160 0
+			0x164 0
+			0x168 0
+			0x16c 0
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0x8000 0x8000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0x8000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0x288 0x388>;
+	};
+
+	board_pins_2: pinmux-board-2 {
+		pinctrl-single,pins = <
+			0x44 1
+			0x48 1
+			0x20 1
+			0x18 1
+			0x14 1
+			0x10 1
+			0xc 1
+			0x8 1
+			0x68 1
+			0x58 0
+			0x54 0
+			0x7c 0
+			0x6c 0
+			0x70 0
+			0x4c 1
+			0x50 1
+			0xac 0
+			0x90 0
+			0x8c 0
+			0x88 0
+			0x84 0
+			0xc8 0
+			0x128 0
+			0x190 0
+			0x194 0
+			0x1a0 0
+			0x114 0
+			0x118 0
+			0x1d8 0
+			0x1e4 0
+			0xe8 0
+			0x100 0
+			0x204 0
+			0x210 0
+			0x218 0
+		>;
+		pinctrl-single,bias-pullup = <0xc000 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0xa000 0x8000 0xc000>;
+		pinctrl-single,low-power-mode = <0x288 0x388>;
+	};
+
+	board_pins_3: pinmux-board-3 {
+		pinctrl-single,pins = <
+			0x260 0
+			0x264 0
+			0x268 0
+			0x26c 0
+			0x270 0
+			0x274 0
+			0x78 0
+			0x74 0
+			0xb0 1
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	uart0_pins: pinmux-uart0 {
+		pinctrl-single,pins = <
+			0x198 6
+			0x19c 6
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	gpio_keys_pins: pinmux-gpio-keys {
+		pinctrl-single,pins = <
+			0x11c 0
+			0x120 0
+			0x1a4 0
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0xc000 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0xa0000 0x8000 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	i2c_muic_pins: pinmux-i2c-muic {
+		pinctrl-single,pins = <
+			0x154 0
+			0x150 0
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0x288 0x388>;
+	};
+
+	sdh0_pins_1: pinmux-sdh0-1 {
+		pinctrl-single,pins = <
+			0x108 0
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0xc000 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0xa000 0x8000 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	sdh0_pins_2: pinmux-sdh0-2 {
+		pinctrl-single,pins = <
+			0x94 0
+			0x98 0
+			0x9c 0
+			0xa0 0
+			0xa4 0
+		>;
+		pinctrl-single,drive-strength = <0x800 0x1800>;
+		pinctrl-single,bias-pullup = <0xc000 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0xa000 0x8000 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	sdh0_pins_3: pinmux-sdh0-3 {
+		pinctrl-single,pins = <
+			0xa8 0
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0x208 0x388>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+};
+
+&twsi0 {
+	status = "okay";
+};
+
+&twsi1 {
+	status = "okay";
+};
+
+&twsi2 {
+	status = "okay";
+};
+
+&twsi3 {
+	status = "okay";
+};
+
+&usb {
+	extcon = <&muic>, <&muic>;
+};
+
+&sdh2 {
+	/* Disabled for now because initialization fails with -ETIMEDOUT. */
+	status = "disabled";
+	bus-width = <8>;
+	non-removable;
+	broken-cd;
+	mmc-ddr-1_8v;
+};
+
+&sdh0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdh0_pins_1 &sdh0_pins_2 &sdh0_pins_3>;
+	cd-gpios = <&gpio 11 0>;
+	cd-inverted;
+	bus-width = <4>;
+	wp-inverted;
+};
diff --git a/arch/arm64/boot/dts/marvell/pxa1908.dtsi b/arch/arm64/boot/dts/marvell/pxa1908.dtsi
new file mode 100644
index 000000000000..cc322b9a0e9e
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/pxa1908.dtsi
@@ -0,0 +1,295 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/marvell,pxa1908.h>
+
+/ {
+	model = "Marvell Armada PXA1908";
+	compatible = "marvell,pxa1908";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0 0>;
+			enable-method = "psci";
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0 1>;
+			enable-method = "psci";
+		};
+
+		cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0 2>;
+			enable-method = "psci";
+		};
+
+		cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0 3>;
+			enable-method = "psci";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		smmu: iommu@c0010000 {
+			compatible = "arm,mmu-400";
+			reg = <0 0xc0010000 0 0x10000>;
+			#global-interrupts = <1>;
+			#iommu-cells = <1>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@d1df9000 {
+			compatible = "arm,gic-400";
+			reg = <0 0xd1df9000 0 0x1000>,
+				<0 0xd1dfa000 0 0x2000>,
+				/* The subsequent registers are guesses. */
+				<0 0xd1dfc000 0 0x2000>,
+				<0 0xd1dfe000 0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		apb@d4000000 {
+			compatible = "simple-bus";
+			reg = <0 0xd4000000 0 0x200000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xd4000000 0x200000>;
+
+			pdma: dma-controller@0 {
+				compatible = "marvell,pdma-1.0";
+				reg = <0 0x10000>;
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				dma-channels = <30>;
+				#dma-cells = <2>;
+			};
+
+			twsi1: i2c@10800 {
+				compatible = "mrvl,mmp-twsi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x10800 0x64>;
+				interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbc PXA1908_CLK_TWSI1>;
+				mrvl,i2c-fast-mode;
+				status = "disabled";
+			};
+
+			twsi0: i2c@11000 {
+				compatible = "mrvl,mmp-twsi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x11000 0x64>;
+				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbc PXA1908_CLK_TWSI0>;
+				mrvl,i2c-fast-mode;
+				status = "disabled";
+			};
+
+			twsi3: i2c@13800 {
+				compatible = "mrvl,mmp-twsi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x13800 0x64>;
+				interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbc PXA1908_CLK_TWSI3>;
+				mrvl,i2c-fast-mode;
+				status = "disabled";
+			};
+
+			apbc: clock-controller@15000 {
+				compatible = "marvell,pxa1908-apbc";
+				reg = <0x15000 0x1000>;
+				#clock-cells = <1>;
+			};
+
+			uart0: serial@17000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
+				reg = <0x17000 0x1000>;
+				interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbc PXA1908_CLK_UART0>;
+				reg-shift = <2>;
+			};
+
+			uart1: serial@18000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
+				reg = <0x18000 0x1000>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbc PXA1908_CLK_UART1>;
+				reg-shift = <2>;
+			};
+
+			gpio: gpio@19000 {
+				compatible = "marvell,mmp-gpio";
+				reg = <0x19000 0x800>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				clocks = <&apbc PXA1908_CLK_GPIO>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "gpio_mux";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ranges = <0 0x19000 0x800>;
+
+				gpio@0 {
+					reg = <0x0 0x4>;
+				};
+
+				gpio@4 {
+					reg = <0x4 0x4>;
+				};
+
+				gpio@8 {
+					reg = <0x8 0x4>;
+				};
+
+				gpio@100 {
+					reg = <0x100 0x4>;
+				};
+			};
+
+			pmx: pinmux@1e000 {
+				compatible = "pinconf-single";
+				reg = <0x1e000 0x330>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#gpio-range-cells = <3>;
+				ranges;
+
+				#pinctrl-cells = <1>;
+				pinctrl-single,register-width = <32>;
+				pinctrl-single,function-mask = <7>;
+
+				range: gpio-range {
+					#pinctrl-single,gpio-range-cells = <3>;
+				};
+			};
+
+			uart2: serial@36000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
+				reg = <0x36000 0x1000>;
+				interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbcp PXA1908_CLK_UART2>;
+				reg-shift = <2>;
+			};
+
+			twsi2: i2c@37000 {
+				compatible = "mrvl,mmp-twsi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x37000 0x64>;
+				interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbcp PXA1908_CLK_TWSI2>;
+				mrvl,i2c-fast-mode;
+				status = "disabled";
+			};
+
+			apbcp: clock-controller@3b000 {
+				compatible = "marvell,pxa1908-apbcp";
+				reg = <0x3b000 0x1000>;
+				#clock-cells = <1>;
+			};
+
+			mpmu: clock-controller@50000 {
+				compatible = "marvell,pxa1908-mpmu";
+				reg = <0x50000 0x1000>;
+				#clock-cells = <1>;
+			};
+		};
+
+		axi@d4200000 {
+			compatible = "simple-bus";
+			reg = <0 0xd4200000 0 0x200000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xd4200000 0x200000>;
+
+			usbphy: phy@7000 {
+				compatible = "marvell,pxa1928-usb-phy";
+				reg = <0x7000 0x200>;
+				clocks = <&apmu PXA1908_CLK_USB>;
+				#phy-cells = <0>;
+			};
+
+			usb: usb@8000 {
+				compatible = "chipidea,usb2";
+				reg = <0x8000 0x200>;
+				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apmu PXA1908_CLK_USB>;
+				phys = <&usbphy>;
+				phy-names = "usb-phy";
+			};
+
+			sdh0: mmc@80000 {
+				compatible = "mrvl,pxav3-mmc";
+				reg = <0x80000 0x120>;
+				interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apmu PXA1908_CLK_SDH0>;
+				clock-names = "io";
+				mrvl,clk-delay-cycles = <31>;
+			};
+
+			sdh1: mmc@80800 {
+				compatible = "mrvl,pxav3-mmc";
+				reg = <0x80800 0x120>;
+				interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apmu PXA1908_CLK_SDH1>;
+				clock-names = "io";
+				mrvl,clk-delay-cycles = <31>;
+			};
+
+			sdh2: mmc@81000 {
+				compatible = "mrvl,pxav3-mmc";
+				reg = <0x81000 0x120>;
+				interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apmu PXA1908_CLK_SDH2>;
+				clock-names = "io";
+				mrvl,clk-delay-cycles = <31>;
+			};
+
+			apmu: clock-controller@82800 {
+				compatible = "marvell,pxa1908-apmu";
+				reg = <0x82800 0x400>;
+				#clock-cells = <1>;
+			};
+		};
+	};
+};