diff mbox series

[v1,6/8] ARM: dts: aspeed: System1: GPIO, Fan ctrl, Led

Message ID 20231212164004.1683589-7-ninad@linux.ibm.com (mailing list archive)
State Superseded
Headers show
Series Add device tree for IBM system1 BMC | expand

Commit Message

Ninad Palsule Dec. 12, 2023, 4:40 p.m. UTC 
This commit adds following devices to the device tree.
- GPIO pin assignements, GPIO expansion devices
- LED brinker devices
- Fan controllers

Tested:
    This board is tested using the simics simulator.

Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
---
 .../dts/aspeed/aspeed-bmc-ibm-system1.dts     | 547 +++++++++++++++++-
 1 file changed, 542 insertions(+), 5 deletions(-)

Comments

Krzysztof Kozlowski Dec. 12, 2023, 8:25 p.m. UTC | #1 
On 12/12/2023 17:40, Ninad Palsule wrote:
> This commit adds following devices to the device tree.
> - GPIO pin assignements, GPIO expansion devices
> - LED brinker devices
> - Fan controllers
> 
> Tested:
>     This board is tested using the simics simulator.
> 
> Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
> ---
>  .../dts/aspeed/aspeed-bmc-ibm-system1.dts     | 547 +++++++++++++++++-

Squash it.

>  1 file changed, 542 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
> index b8e7e52d4600..75562aa63701 100644
> --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
> @@ -114,6 +114,99 @@ vga_memory: region@bf000000 {
>  		};
>  	};
>  
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		bmc-ready {

It does not look like you tested the DTS against bindings. Please run
`make dtbs_check W=1` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).

> +			gpios = <&gpio0 ASPEED_GPIO(L, 7) GPIO_ACTIVE_HIGH>;
> +		};
> +
> +		bmc-hb {

None of these were tested.


>  	/*A0-A7*/	"","","","","","","","",
> -	/*B0-B7*/	"","","","","","","","",
> +	/*B0-B7*/	"","","","","bmc-tpm-reset","","","",

Really? You just added these lines. There is no point in adding a new
line and immediately changing it.

This points how your split is artificial and not helpful.
...


>  &i2c2 {
> @@ -486,6 +744,20 @@ regulator@43 {
>  &i2c6 {
>  	status = "okay";
>  
> +	fan-controller@52 {
> +		compatible = "maxim,max31785a";
> +		reg = <0x52>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;

Why do you need cells?

> +	};
> +
> +	fan-controller@54 {
> +		compatible = "maxim,max31785a";
> +		reg = <0x54>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;

Why do you need cells?

> +	};
> +
>  	i2c-mux@70 {
>  		compatible = "nxp,pca9548";
>  		reg = <0x70>;
> @@ -522,6 +794,48 @@ i2c6mux0chn4: i2c@4 {
>  			#address-cells = <1>;
>  			#size-cells = <0>;
>  			reg = <4>;
> +
> +			led-controller@60 {
> +				compatible = "nxp,pca9551";
> +				reg = <0x60>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +
> +				led@0 {
> +					label = "enclosure-id-led";
> +					reg = <0>;
> +					retain-state-shutdown;
> +					default-state = "keep";
> +					type = <PCA955X_TYPE_LED>;
> +				};
> +
> +				led@1 {
> +					label = "attention-led";
> +					reg = <1>;
> +					retain-state-shutdown;
> +					default-state = "keep";
> +					type = <PCA955X_TYPE_LED>;
> +				};
> +
> +				led@2 {
> +					label = "enclosure-fault-rollup-led";
> +					reg = <2>;
> +					retain-state-shutdown;
> +					default-state = "keep";
> +					type = <PCA955X_TYPE_LED>;
> +				};
> +
> +				led@3 {
> +					label = "power-on-led";
> +					reg = <3>;
> +					retain-state-shutdown;
> +					default-state = "keep";
> +					type = <PCA955X_TYPE_LED>;
> +				};
> +			};
>  		};
>  
>  		i2c6mux0chn5: i2c@5 {
> @@ -542,6 +856,44 @@ i2c6mux0chn7: i2c@7 {
>  			reg = <7>;
>  		};
>  	};
> +
> +	pca3: pca9539@74 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation


> +		compatible = "nxp,pca9539";
> +		reg = <0x74>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +	};
> +
> +	pca4: pca9539@77 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation


> +		compatible = "nxp,pca9539";
> +		reg = <0x77>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		gpio-line-names =
> +			"PE_NVMED0_EXP_PRSNT_N",
> +			"PE_NVMED1_EXP_PRSNT_N",
> +			"PE_NVMED2_EXP_PRSNT_N",
> +			"PE_NVMED3_EXP_PRSNT_N",
> +			"LED_FAULT_NVMED0",
> +			"LED_FAULT_NVMED1",
> +			"LED_FAULT_NVMED2",
> +			"LED_FAULT_NVMED3",
> +			"FAN0_PRESENCE_R_N",
> +			"FAN1_PRESENCE_R_N",
> +			"FAN2_PRESENCE_R_N",
> +			"FAN3_PRESENCE_R_N",
> +			"FAN4_PRESENCE_R_N",
> +			"FAN5_PRESENCE_N",
> +			"FAN6_PRESENCE_N",
> +			"";
> +	};
>  };
>  
>  &i2c7 {
> @@ -809,6 +1161,191 @@ regulator@41 {
>  		compatible = "infineon,ir38263";
>  		reg = <0x41>;
>  	};
> +
> +	led-controller@61 {
> +		compatible = "nxp,pca9552";
> +		reg = <0x61>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +

...

> +		led@15 {
> +			label = "pe-cp-drv3-perst";
> +			reg = <15>;
> +			retain-state-shutdown;
> +			default-state = "keep";
> +			type = <PCA955X_TYPE_LED>;
> +		};
> +	};
> +
> +	pca1: pca9539@75 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation




Best regards,
Krzysztof
Ninad Palsule Jan. 8, 2024, 7:56 p.m. UTC | #2 
Hello Krzysztof,

On 12/12/23 14:25, Krzysztof Kozlowski wrote:
> On 12/12/2023 17:40, Ninad Palsule wrote:
>> This commit adds following devices to the device tree.
>> - GPIO pin assignements, GPIO expansion devices
>> - LED brinker devices
>> - Fan controllers
>>
>> Tested:
>>      This board is tested using the simics simulator.
>>
>> Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
>> ---
>>   .../dts/aspeed/aspeed-bmc-ibm-system1.dts     | 547 +++++++++++++++++-
> Squash it.

Yes, I made a single commit for device tree.

>
>>   1 file changed, 542 insertions(+), 5 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
>> index b8e7e52d4600..75562aa63701 100644
>> --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
>> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
>> @@ -114,6 +114,99 @@ vga_memory: region@bf000000 {
>>   		};
>>   	};
>>   
>> +	leds {
>> +		compatible = "gpio-leds";
>> +
>> +		bmc-ready {
> It does not look like you tested the DTS against bindings. Please run
> `make dtbs_check W=1` (see
> Documentation/devicetree/bindings/writing-schema.rst or
> https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
> for instructions).
Fixed names.
>
>> +			gpios = <&gpio0 ASPEED_GPIO(L, 7) GPIO_ACTIVE_HIGH>;
>> +		};
>> +
>> +		bmc-hb {
> None of these were tested.
Fixed names
>
>>   	/*A0-A7*/	"","","","","","","","",
>> -	/*B0-B7*/	"","","","","","","","",
>> +	/*B0-B7*/	"","","","","bmc-tpm-reset","","","",
> Really? You just added these lines. There is no point in adding a new
> line and immediately changing it.
>
> This points how your split is artificial and not helpful.
> ...
Now I have a single commit for device tree.
>
>
>>   &i2c2 {
>> @@ -486,6 +744,20 @@ regulator@43 {
>>   &i2c6 {
>>   	status = "okay";
>>   
>> +	fan-controller@52 {
>> +		compatible = "maxim,max31785a";
>> +		reg = <0x52>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
> Why do you need cells?
Removed cells.
>
>> +	};
>> +
>> +	fan-controller@54 {
>> +		compatible = "maxim,max31785a";
>> +		reg = <0x54>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
> Why do you need cells?
Removed cells.
>
>> +	};
>> +
>>   	i2c-mux@70 {
>>   		compatible = "nxp,pca9548";
>>   		reg = <0x70>;
>> @@ -522,6 +794,48 @@ i2c6mux0chn4: i2c@4 {
>>   			#address-cells = <1>;
>>   			#size-cells = <0>;
>>   			reg = <4>;
>> +
>> +			led-controller@60 {
>> +				compatible = "nxp,pca9551";
>> +				reg = <0x60>;
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				gpio-controller;
>> +				#gpio-cells = <2>;
>> +
>> +				led@0 {
>> +					label = "enclosure-id-led";
>> +					reg = <0>;
>> +					retain-state-shutdown;
>> +					default-state = "keep";
>> +					type = <PCA955X_TYPE_LED>;
>> +				};
>> +
>> +				led@1 {
>> +					label = "attention-led";
>> +					reg = <1>;
>> +					retain-state-shutdown;
>> +					default-state = "keep";
>> +					type = <PCA955X_TYPE_LED>;
>> +				};
>> +
>> +				led@2 {
>> +					label = "enclosure-fault-rollup-led";
>> +					reg = <2>;
>> +					retain-state-shutdown;
>> +					default-state = "keep";
>> +					type = <PCA955X_TYPE_LED>;
>> +				};
>> +
>> +				led@3 {
>> +					label = "power-on-led";
>> +					reg = <3>;
>> +					retain-state-shutdown;
>> +					default-state = "keep";
>> +					type = <PCA955X_TYPE_LED>;
>> +				};
>> +			};
>>   		};
>>   
>>   		i2c6mux0chn5: i2c@5 {
>> @@ -542,6 +856,44 @@ i2c6mux0chn7: i2c@7 {
>>   			reg = <7>;
>>   		};
>>   	};
>> +
>> +	pca3: pca9539@74 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
Fixed node names.
>
>
>> +		compatible = "nxp,pca9539";
>> +		reg = <0x74>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +	};
>> +
>> +	pca4: pca9539@77 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
Fixed node names.
>
>
>> +		compatible = "nxp,pca9539";
>> +		reg = <0x77>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		gpio-line-names =
>> +			"PE_NVMED0_EXP_PRSNT_N",
>> +			"PE_NVMED1_EXP_PRSNT_N",
>> +			"PE_NVMED2_EXP_PRSNT_N",
>> +			"PE_NVMED3_EXP_PRSNT_N",
>> +			"LED_FAULT_NVMED0",
>> +			"LED_FAULT_NVMED1",
>> +			"LED_FAULT_NVMED2",
>> +			"LED_FAULT_NVMED3",
>> +			"FAN0_PRESENCE_R_N",
>> +			"FAN1_PRESENCE_R_N",
>> +			"FAN2_PRESENCE_R_N",
>> +			"FAN3_PRESENCE_R_N",
>> +			"FAN4_PRESENCE_R_N",
>> +			"FAN5_PRESENCE_N",
>> +			"FAN6_PRESENCE_N",
>> +			"";
>> +	};
>>   };
>>   
>>   &i2c7 {
>> @@ -809,6 +1161,191 @@ regulator@41 {
>>   		compatible = "infineon,ir38263";
>>   		reg = <0x41>;
>>   	};
>> +
>> +	led-controller@61 {
>> +		compatible = "nxp,pca9552";
>> +		reg = <0x61>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
> ...
>
>> +		led@15 {
>> +			label = "pe-cp-drv3-perst";
>> +			reg = <15>;
>> +			retain-state-shutdown;
>> +			default-state = "keep";
>> +			type = <PCA955X_TYPE_LED>;
>> +		};
>> +	};
>> +
>> +	pca1: pca9539@75 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
Fixed names.

Thanks for the review.

Regards,

Ninad
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
index b8e7e52d4600..75562aa63701 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
@@ -114,6 +114,99 @@  vga_memory: region@bf000000 {
 		};
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		bmc-ready {
+			gpios = <&gpio0 ASPEED_GPIO(L, 7) GPIO_ACTIVE_HIGH>;
+		};
+
+		bmc-hb {
+			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_HIGH>;
+		};
+
+		rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(S, 6) GPIO_ACTIVE_HIGH>;
+		};
+
+		rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
+		};
+
+		fan0-fault-led {
+			gpios = <&pca3 5 GPIO_ACTIVE_LOW>;
+		};
+
+		fan1-fault-led {
+			gpios = <&pca3 6 GPIO_ACTIVE_LOW>;
+		};
+
+		fan2-fault-led {
+			gpios = <&pca3 7 GPIO_ACTIVE_LOW>;
+		};
+
+		fan3-fault-led {
+			gpios = <&pca3 8 GPIO_ACTIVE_LOW>;
+		};
+
+		fan4-fault-led {
+			gpios = <&pca3 9 GPIO_ACTIVE_LOW>;
+		};
+
+		fan5-fault-led {
+			gpios = <&pca3 10 GPIO_ACTIVE_LOW>;
+		};
+
+		fan6-fault-led {
+			gpios = <&pca3 11 GPIO_ACTIVE_LOW>;
+		};
+
+		nvmed0-fault-led {
+			gpios = <&pca4 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		nvmed1-fault-led {
+			gpios = <&pca4 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		nvmed2-fault-led {
+			gpios = <&pca4 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		nvmed3-fault-led {
+			gpios = <&pca4 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <1000>;
+
+		event-nvme0-presence {
+			label = "nvme0-presence";
+			gpios = <&pca4 0 GPIO_ACTIVE_LOW>;
+			linux,code = <0>;
+		};
+
+		event-nvme1-presence {
+			label = "nvme1-presence";
+			gpios = <&pca4 1 GPIO_ACTIVE_LOW>;
+			linux,code = <1>;
+		};
+
+		event-nvme2-presence {
+			label = "nvme2-presence";
+			gpios = <&pca4 2 GPIO_ACTIVE_LOW>;
+			linux,code = <2>;
+		};
+
+		event-nvme3-presence {
+			label = "nvme3-presence";
+			gpios = <&pca4 3 GPIO_ACTIVE_LOW>;
+			linux,code = <3>;
+		};
+	};
+
 	iio-hwmon {
 		compatible = "iio-hwmon";
 		io-channels = <&p12v_vd 0>, <&p5v_aux_vd 0>,
@@ -259,7 +352,7 @@  &uhci {
 &gpio0 {
 	gpio-line-names =
 	/*A0-A7*/	"","","","","","","","",
-	/*B0-B7*/	"","","","","","","","",
+	/*B0-B7*/	"","","","","bmc-tpm-reset","","","",
 	/*C0-C7*/	"","","","","","","","",
 	/*D0-D7*/	"","","","","","","","",
 	/*E0-E7*/	"","","","","","","","",
@@ -269,17 +362,17 @@  &gpio0 {
 	/*I0-I7*/	"","","","","","","","",
 	/*J0-J7*/	"","","","","","","","",
 	/*K0-K7*/	"","","","","","","","",
-	/*L0-L7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","bmc-ready",
 	/*M0-M7*/	"","","","","","","","",
 	/*N0-N7*/	"","","","","","","","",
 	/*O0-O7*/	"","","","","","","","",
-	/*P0-P7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","bmc-hb",
 	/*Q0-Q7*/	"","","","","","","","",
 	/*R0-R7*/	"","","","","","","","",
-	/*S0-S7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","rear-enc-fault0","rear-enc-id0",
 	/*T0-T7*/	"","","","","","","","",
 	/*U0-U7*/	"","","","","","","","",
-	/*V0-V7*/	"","","","power-chassis-control","","","","",
+	/*V0-V7*/	"","rtc-battery-voltage-read-enable","","power-chassis-control","","","","",
 	/*W0-W7*/	"","","","","","","","",
 	/*X0-X7*/	"","power-chassis-good","","","","","","",
 	/*Y0-Y7*/	"","","","","","","","",
@@ -393,6 +486,171 @@  regulator@42 {
 		compatible = "infineon,ir38263";
 		reg = <0x42>;
 	};
+
+	led-controller@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "nic1-perst";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "bmc-perst";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "reset-M2-SSD1-2-perst";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "pcie-perst1";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "pcie-perst2";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "pcie-perst3";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "pcie-perst4";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "pcie-perst5";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "pcie-perst6";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "pcie-perst7";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "pcie-perst8";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "PV-cp0-sw1stk4-perst";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "PV-cp0-sw1stk5-perst";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "pe-cp-drv0-perst";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "pe-cp-drv1-perst";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "lom-perst";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca0: pca9539@74 {
+		compatible = "nxp,pca9539";
+		reg = <0x74>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"PLUG_DETECT_PCIE_J101_N",
+			"PLUG_DETECT_PCIE_J102_N",
+			"PLUG_DETECT_PCIE_J103_N",
+			"PLUG_DETECT_PCIE_J104_N",
+			"PLUG_DETECT_PCIE_J105_N",
+			"PLUG_DETECT_PCIE_J106_N",
+			"PLUG_DETECT_PCIE_J107_N",
+			"PLUG_DETECT_PCIE_J108_N",
+			"PLUG_DETECT_M2_SSD1_N",
+			"PLUG_DETECT_NIC1_N",
+			"SEL_SMB_DIMM_CPU0",
+			"presence-ps2",
+			"presence-ps3",
+			"", "",
+			"PWRBRD_PLUG_DETECT2_N";
+	};
 };
 
 &i2c2 {
@@ -486,6 +744,20 @@  regulator@43 {
 &i2c6 {
 	status = "okay";
 
+	fan-controller@52 {
+		compatible = "maxim,max31785a";
+		reg = <0x52>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	fan-controller@54 {
+		compatible = "maxim,max31785a";
+		reg = <0x54>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
 	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		reg = <0x70>;
@@ -522,6 +794,48 @@  i2c6mux0chn4: i2c@4 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <4>;
+
+			led-controller@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "enclosure-id-led";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "attention-led";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@2 {
+					label = "enclosure-fault-rollup-led";
+					reg = <2>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@3 {
+					label = "power-on-led";
+					reg = <3>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
 		};
 
 		i2c6mux0chn5: i2c@5 {
@@ -542,6 +856,44 @@  i2c6mux0chn7: i2c@7 {
 			reg = <7>;
 		};
 	};
+
+	pca3: pca9539@74 {
+		compatible = "nxp,pca9539";
+		reg = <0x74>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca4: pca9539@77 {
+		compatible = "nxp,pca9539";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"PE_NVMED0_EXP_PRSNT_N",
+			"PE_NVMED1_EXP_PRSNT_N",
+			"PE_NVMED2_EXP_PRSNT_N",
+			"PE_NVMED3_EXP_PRSNT_N",
+			"LED_FAULT_NVMED0",
+			"LED_FAULT_NVMED1",
+			"LED_FAULT_NVMED2",
+			"LED_FAULT_NVMED3",
+			"FAN0_PRESENCE_R_N",
+			"FAN1_PRESENCE_R_N",
+			"FAN2_PRESENCE_R_N",
+			"FAN3_PRESENCE_R_N",
+			"FAN4_PRESENCE_R_N",
+			"FAN5_PRESENCE_N",
+			"FAN6_PRESENCE_N",
+			"";
+	};
 };
 
 &i2c7 {
@@ -809,6 +1161,191 @@  regulator@41 {
 		compatible = "infineon,ir38263";
 		reg = <0x41>;
 	};
+
+	led-controller@61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "efuse-12v-slots";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "efuse-3p3v-slot";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "nic2-pert";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "pcie-perst9";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "pcie-perst10";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "pcie-perst11";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "pcie-perst12";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "pcie-perst13";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "pcie-perst14";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "pcie-perst15";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "pcie-perst16";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "PV-cp1-sw1stk4-perst";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "PV-cp1-sw1stk5-perst";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "pe-cp-drv2-perst";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "pe-cp-drv3-perst";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca1: pca9539@75 {
+		compatible = "nxp,pca9539";
+		reg = <0x75>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"PLUG_DETECT_PCIE_J109_N",
+			"PLUG_DETECT_PCIE_J110_N",
+			"PLUG_DETECT_PCIE_J111_N",
+			"PLUG_DETECT_PCIE_J112_N",
+			"PLUG_DETECT_PCIE_J113_N",
+			"PLUG_DETECT_PCIE_J114_N",
+			"PLUG_DETECT_PCIE_J115_N",
+			"PLUG_DETECT_PCIE_J116_N",
+			"PLUG_DETECT_M2_SSD2_N",
+			"PLUG_DETECT_NIC2_N",
+			"SEL_SMB_DIMM_CPU1",
+			"presence-ps0",
+			"presence-ps1",
+			"", "",
+			"PWRBRD_PLUG_DETECT1_N";
+	};
+
+	pca2: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SW1_BOOTRCVRYB1_N",
+			"SW1_BOOTRCVRYB0_N",
+			"SW2_BOOTRCVRYB1_N",
+			"SW2_BOOTRCVRYB0_N",
+			"SW3_4_BOOTRCVRYB1_N",
+			"SW3_4_BOOTRCVRYB0_N",
+			"SW5_BOOTRCVRYB1_N",
+			"SW5_BOOTRCVRYB0_N",
+			"SW6_BOOTRCVRYB1_N",
+			"SW6_BOOTRCVRYB0_N",
+			"SW1_RESET_N",
+			"SW3_RESET_N",
+			"SW4_RESET_N",
+			"SW2_RESET_N",
+			"SW5_RESET_N",
+			"SW6_RESET_N";
+	};
 };
 
 &i2c14 {