| Message ID | 20240210-topic-1v-v1-7-fda0db38e29b@linaro.org (mailing list archive) |
|---|---|
| State | Mainlined |
| Commit | 39c596304e44781c1950ea0cbf178d6433ff9c71 |
| Headers | show |
| Series | Xperia 1 V support | expand |
On 12/02/2024 14:10, Konrad Dybcio wrote: > Add support for Sony Xperia 1 V, a.k.a PDX234. This device is a part > of the SoMC SM8550 Yodo platform. > > This commit brings support for: > * Remoteprocs (sans modem for now) > * Flash LED (the notification LED is gone :((((() > * SD Card > * USB (*including SuperSpeed*) + PMIC_GLINK (it's funky, requires a replug > with an cable flip sometimes..) > * Most regulators > * Part of I2C-connected peripherals (notably no touch due to a > driver bug) > * PCIe0 (PCIe1 is unused) > > Do note display via simplefb is not supported, as the display is blanked > upon exiting XBL. > > To create a working boot image, you need to run: > cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/sm8550-sony-xperia-\ > yodo-pdx234.dtb > .Image.gz-dtb > > mkbootimg \ > --kernel .Image.gz-dtb \ > --ramdisk some_initrd.img \ > --pagesize 4096 \ > --base 0x0 \ > --kernel_offset 0x8000 \ > --ramdisk_offset 0x1000000 \ > --tags_offset 0x100 \ > --cmdline "SOME_CMDLINE" \ > --dtb_offset 0x1f00000 \ > --header_version 2 \ > -o boot.img-sony-xperia-pdx234 > > Then, you need to flash it on the device and get rid of all the > vendor_boot/dtbo mess: > > // You have to either pull vbmeta{"","_system"} from > // /dev/block/bootdevice/by-name/ or build one as a part of AOSP build process > fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img > fastboot --disable-verity --disable-verification flash vbmeta_system \ > vbmeta_system.img > > fastboot flash boot boot.img-sony-xperia-pdx234 > fastboot erase vendor_boot > fastboot erase recovery > fastboot flash dtbo emptydtbo.img > fastboot erase init_boot // ? I don't remember if it's necessary, sorry > fastboot continue > > Where emptydtbo.img is a tiny file that consists of 2 bytes (all zeroes), doing > a "fastboot erase" won't cut it, the bootloader will go crazy and things will > fall apart when it tries to overlay random bytes from an empty partition onto a > perfectly good appended DTB. DTBc check reports: arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dtb: pcie-1-phy-aux-clk: 'clock-frequency' is a required property from schema $id: http://devicetree.org/schemas/clock/fixed-clock.yaml# So you'll probably need: &pcie_1_phy_aux_clk { status = "disabled"; }; > > Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts | 779 +++++++++++++++++++++ > 2 files changed, 780 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index f7c5662213e4..9bbea531660d 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -237,6 +237,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx224.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8550-hdk.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8550-mtp.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8550-qrd.dtb > +dtb-$(CONFIG_ARCH_QCOM) += sm8550-sony-xperia-yodo-pdx234.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb > dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb > diff --git a/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts b/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts > new file mode 100644 > index 000000000000..85e0d3d66e16 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts > @@ -0,0 +1,779 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2023, Linaro Limited > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/firmware/qcom,scm.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> > +#include <dt-bindings/sound/cs35l45.h> > +#include "sm8550.dtsi" > +#include "pm8010.dtsi" > +#include "pm8550.dtsi" > +#include "pm8550b.dtsi" > +#define PMK8550VE_SID 5 > +#include "pm8550ve.dtsi" > +#include "pm8550vs.dtsi" > +#include "pmk8550.dtsi" > +/* TODO: Only one SID of PMR735D seems accessible? */ What's reported by the cpuinfo pmic array ? <snip> With the pcie thing fixed: Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
On 2/12/24 18:26, Neil Armstrong wrote: > On 12/02/2024 14:10, Konrad Dybcio wrote: >> Add support for Sony Xperia 1 V, a.k.a PDX234. This device is a part >> of the SoMC SM8550 Yodo platform. >> [...] >> +/* TODO: Only one SID of PMR735D seems accessible? */ > > > What's reported by the cpuinfo pmic array ? PMK8550 2.1 PM8550 2.0 PM8550VS 2.0 PM8550VS 2.0 PM8550VS 2.0 PM8550VE 2.0 PM8550VS 2.0 PM8550B 2.0 PMR735D 2.0 PM8010 1.1 PM8010 1.1 Not sure if there's only one or the other one is secure? > > <snip> > > With the pcie thing fixed: > Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> It's gonna be fine with the recent aux clock additions. If you have no further comments, I'll happily ask for this to be merged ;) Konrad
On 04/04/2024 21:41, Konrad Dybcio wrote: > > > On 2/12/24 18:26, Neil Armstrong wrote: >> On 12/02/2024 14:10, Konrad Dybcio wrote: >>> Add support for Sony Xperia 1 V, a.k.a PDX234. This device is a part >>> of the SoMC SM8550 Yodo platform. >>> > > [...] > >>> +/* TODO: Only one SID of PMR735D seems accessible? */ >> >> >> What's reported by the cpuinfo pmic array ? > > PMK8550 2.1 > PM8550 2.0 > PM8550VS 2.0 > PM8550VS 2.0 > PM8550VS 2.0 > PM8550VE 2.0 > PM8550VS 2.0 > PM8550B 2.0 > PMR735D 2.0 > PM8010 1.1 > PM8010 1.1 > > Not sure if there's only one or the other one is secure? > >> >> <snip> >> >> With the pcie thing fixed: >> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> > > It's gonna be fine with the recent aux clock additions. If you > have no further comments, I'll happily ask for this to be merged ;) Sure LGTM > > Konrad
W dniu 2024-02-12 14:10, Konrad Dybcio napisał(a): > Add support for Sony Xperia 1 V, a.k.a PDX234. This device is a part > of the SoMC SM8550 Yodo platform. > > This commit brings support for: > * Remoteprocs (sans modem for now) > * Flash LED (the notification LED is gone :((((() > * SD Card > * USB (*including SuperSpeed*) + PMIC_GLINK (it's funky, requires a > replug > with an cable flip sometimes..) > * Most regulators > * Part of I2C-connected peripherals (notably no touch due to a > driver bug) > * PCIe0 (PCIe1 is unused) > > Do note display via simplefb is not supported, as the display is > blanked > upon exiting XBL. > I also noticed such behaviour on my S24 Ultra. I was pointed out by Xilin Wu that on SM8450 or newer, the display will be turned off by the bootloader if the node '/reserved-memory/splash_region' does not exist in the device tree. Adding it in the device tree for my phone made the bootloader leave the display on. Maybe it's the same case here? https://git.codelinaro.org/clo/la/abl/tianocore/edk2/-/blob/LA.VENDOR.1.0.r2-09400-WAIPIO.QSSI14.0/QcomModulePkg/Library/BootLib/UpdateDeviceTree.c?ref_type=tags#L220 > To create a working boot image, you need to run: > cat arch/arm64/boot/Image.gz > arch/arm64/boot/dts/qcom/sm8550-sony-xperia-\ > yodo-pdx234.dtb > .Image.gz-dtb > > mkbootimg \ > --kernel .Image.gz-dtb \ > --ramdisk some_initrd.img \ > --pagesize 4096 \ > --base 0x0 \ > --kernel_offset 0x8000 \ > --ramdisk_offset 0x1000000 \ > --tags_offset 0x100 \ > --cmdline "SOME_CMDLINE" \ > --dtb_offset 0x1f00000 \ > --header_version 2 \ > -o boot.img-sony-xperia-pdx234 > > Then, you need to flash it on the device and get rid of all the > vendor_boot/dtbo mess: > > // You have to either pull vbmeta{"","_system"} from > // /dev/block/bootdevice/by-name/ or build one as a part of AOSP build > process > fastboot --disable-verity --disable-verification flash vbmeta > vbmeta.img > fastboot --disable-verity --disable-verification flash vbmeta_system \ > vbmeta_system.img > > fastboot flash boot boot.img-sony-xperia-pdx234 > fastboot erase vendor_boot > fastboot erase recovery > fastboot flash dtbo emptydtbo.img > fastboot erase init_boot // ? I don't remember if it's necessary, sorry > fastboot continue > > Where emptydtbo.img is a tiny file that consists of 2 bytes (all > zeroes), doing > a "fastboot erase" won't cut it, the bootloader will go crazy and > things will > fall apart when it tries to overlay random bytes from an empty > partition onto a > perfectly good appended DTB. > > Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts | 779 > +++++++++++++++++++++ > 2 files changed, 780 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/Makefile > b/arch/arm64/boot/dts/qcom/Makefile > index f7c5662213e4..9bbea531660d 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -237,6 +237,7 @@ dtb-$(CONFIG_ARCH_QCOM) += > sm8450-sony-xperia-nagara-pdx224.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8550-hdk.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8550-mtp.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8550-qrd.dtb > +dtb-$(CONFIG_ARCH_QCOM) += sm8550-sony-xperia-yodo-pdx234.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb > dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb > dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb > diff --git > a/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts > b/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts > new file mode 100644 > index 000000000000..85e0d3d66e16 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts > @@ -0,0 +1,779 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2023, Linaro Limited > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/firmware/qcom,scm.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> > +#include <dt-bindings/sound/cs35l45.h> > +#include "sm8550.dtsi" > +#include "pm8010.dtsi" > +#include "pm8550.dtsi" > +#include "pm8550b.dtsi" > +#define PMK8550VE_SID 5 > +#include "pm8550ve.dtsi" > +#include "pm8550vs.dtsi" > +#include "pmk8550.dtsi" > +/* TODO: Only one SID of PMR735D seems accessible? */ > + > +/delete-node/ &hwfence_shbuf; > +/delete-node/ &mpss_mem; > +/delete-node/ &rmtfs_mem; > +/ { > + model = "Sony Xperia 1 V"; > + compatible = "sony,pdx234", "qcom,sm8550"; > + chassis-type = "handset"; > + > + aliases { > + i2c0 = &i2c0; > + i2c4 = &i2c4; > + i2c10 = &i2c10; > + i2c11 = &i2c11; > + i2c16 = &i2c_hub_2; > + serial0 = &uart7; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + label = "gpio-keys"; > + > + pinctrl-0 = <&focus_n &snapshot_n &vol_down_n>; > + pinctrl-names = "default"; > + > + key-camera-focus { > + label = "Camera Focus"; > + linux,code = <KEY_CAMERA_FOCUS>; > + gpios = <&pm8550b_gpios 8 GPIO_ACTIVE_LOW>; > + debounce-interval = <15>; > + linux,can-disable; > + wakeup-source; > + }; > + > + key-camera-snapshot { > + label = "Camera Snapshot"; > + gpios = <&pm8550b_gpios 7 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_CAMERA>; > + debounce-interval = <15>; > + linux,can-disable; > + wakeup-source; > + }; > + > + key-volume-down { > + label = "Volume Down"; > + linux,code = <KEY_VOLUMEDOWN>; > + gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>; > + debounce-interval = <15>; > + linux,can-disable; > + wakeup-source; > + }; > + }; > + > + pmic-glink { > + compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink"; > + orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + connector@0 { > + compatible = "usb-c-connector"; > + reg = <0>; > + power-role = "dual"; > + data-role = "dual"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + pmic_glink_hs_in: endpoint { > + remote-endpoint = <&usb_1_dwc3_hs>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + pmic_glink_ss_in: endpoint { > + remote-endpoint = <&usb_dp_qmpphy_out>; > + }; > + }; > + }; > + }; > + }; > + > + reserved-memory { > + mpss_mem: mpss-region@89800000 { > + reg = <0x0 0x89800000 0x0 0x10800000>; > + no-map; > + }; > + > + splash@b8000000 { > + reg = <0x0 0xb8000000 0x0 0x2b00000>; > + no-map; > + }; > + > + hwfence_shbuf: hwfence-shbuf-region@e6440000 { > + reg = <0x0 0xe6440000 0x0 0x2dd000>; > + no-map; > + }; > + > + rmtfs_mem: memory@f8b00000 { > + compatible = "qcom,rmtfs-mem"; > + reg = <0x0 0xf8b00000 0x0 0x280000>; > + no-map; > + > + qcom,client-id = <1>; > + qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>; > + }; > + > + ramoops@ffd00000 { > + compatible = "ramoops"; > + reg = <0x0 0xffd00000 0x0 0xc0000>; > + console-size = <0x40000>; > + record-size = <0x1000>; > + pmsg-size = <0x40000>; > + ecc-size = <16>; > + }; > + > + rdtag-store-region@ffdc0000 { > + reg = <0x0 0xffdc0000 0x0 0x40000>; > + no-map; > + }; > + }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vph_pwr"; > + regulator-min-microvolt = <3700000>; > + regulator-max-microvolt = <3700000>; > + > + regulator-always-on; > + regulator-boot-on; > + }; > +}; > + > +&apps_rsc { > + regulators-0 { > + compatible = "qcom,pm8550-rpmh-regulators"; > + qcom,pmic-id = "b"; > + > + pm8550_bob1: bob1 { > + regulator-name = "pm8550_bob1"; > + regulator-min-microvolt = <3416000>; > + regulator-max-microvolt = <3960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + /* TODO: bob2 @ 2.704-3.008V doesn't fall into the vreg driver > constraints */ > + > + pm8550_l1: ldo1 { > + regulator-name = "pm8550_l1"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l2: ldo2 { > + regulator-name = "pm8550_l2"; > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + /* L4 exists in cmd-db, but the board seems to crash on access */ > + > + pm8550_l5: ldo5 { > + regulator-name = "pm8550_l5"; > + regulator-min-microvolt = <3104000>; > + regulator-max-microvolt = <3104000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l6: ldo6 { > + regulator-name = "pm8550_l6"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l7: ldo7 { > + regulator-name = "pm8550_l7"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l8: ldo8 { > + regulator-name = "pm8550_l8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l9: ldo9 { > + regulator-name = "pm8550_l9"; > + regulator-min-microvolt = <2960000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l10: ldo10 { > + regulator-name = "pm8550_l10"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l11: ldo11 { > + regulator-name = "pm8550_l11"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1504000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l12: ldo12 { > + regulator-name = "pm8550_l12"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l13: ldo13 { > + regulator-name = "pm8550_l13"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l14: ldo14 { > + regulator-name = "pm8550_l14"; > + regulator-min-microvolt = <3304000>; > + regulator-max-microvolt = <3304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l15: ldo15 { > + regulator-name = "pm8550_l15"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l16: ldo16 { > + regulator-name = "pm8550_l16"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550_l17: ldo17 { > + regulator-name = "pm8550_l17"; > + regulator-min-microvolt = <2504000>; > + regulator-max-microvolt = <2504000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-1 { > + compatible = "qcom,pm8550vs-rpmh-regulators"; > + qcom,pmic-id = "c"; > + > + pm8550vs_0_l1: ldo1 { > + regulator-name = "pm8550vs_0_l1"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_0_l3: ldo3 { > + regulator-name = "pm8550vs_0_l3"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <912000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-2 { > + compatible = "qcom,pm8550vs-rpmh-regulators"; > + qcom,pmic-id = "d"; > + > + pm8550vs_1_l1: ldo1 { > + regulator-name = "pm8550vs_1_l1"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <920000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + /* L3 exists in cmd-db, but the board seems to crash on access */ > + }; > + > + regulators-3 { > + compatible = "qcom,pm8550vs-rpmh-regulators"; > + qcom,pmic-id = "e"; > + > + pm8550vs_2_s4: smps4 { > + regulator-name = "pm8550vs_2_s4"; > + regulator-min-microvolt = <904000>; > + regulator-max-microvolt = <984000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_2_s5: smps5 { > + regulator-name = "pm8550vs_2_s5"; > + regulator-min-microvolt = <1010000>; > + regulator-max-microvolt = <1120000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_2_l1: ldo1 { > + regulator-name = "pm8550vs_2_l1"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <912000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_2_l2: ldo2 { > + regulator-name = "pm8550vs_2_l2"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <968000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_2_l3: ldo3 { > + regulator-name = "pm8550vs_2_l3"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-4 { > + compatible = "qcom,pm8550ve-rpmh-regulators"; > + qcom,pmic-id = "f"; > + > + pm8550ve_s4: smps4 { > + regulator-name = "pm8550ve_s4"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <700000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550ve_l1: ldo1 { > + regulator-name = "pm8550ve_l1"; > + regulator-min-microvolt = <912000>; > + regulator-max-microvolt = <912000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550ve_l2: ldo2 { > + regulator-name = "pm8550ve_l2"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <912000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550ve_l3: ldo3 { > + regulator-name = "pm8550ve_l3"; > + regulator-min-microvolt = <912000>; > + regulator-max-microvolt = <912000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-5 { > + compatible = "qcom,pm8550vs-rpmh-regulators"; > + qcom,pmic-id = "g"; > + > + pm8550vs_3_s1: smps1 { > + regulator-name = "pm8550vs_3_s1"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1300000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_3_s2: smps2 { > + regulator-name = "pm8550vs_3_s2"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <1036000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_3_s3: smps3 { > + regulator-name = "pm8550vs_3_s3"; > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <1004000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_3_s4: smps4 { > + regulator-name = "pm8550vs_3_s4"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1352000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_3_s5: smps5 { > + regulator-name = "pm8550vs_3_s5"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <1004000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_3_s6: smps6 { > + regulator-name = "pm8550vs_3_s6"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_3_l1: ldo1 { > + regulator-name = "pm8550vs_3_l1"; > + regulator-min-microvolt = <1144000>; > + regulator-max-microvolt = <1256000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_3_l2: ldo2 { > + regulator-name = "pm8550vs_3_l2"; > + regulator-min-microvolt = <1104000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + pm8550vs_3_l3: ldo3 { > + regulator-name = "pm8550vs_3_l3"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + /* TODO: Unknown PMIC @ k, l, PM8010 @ m, n */ > +}; > + > +&gpi_dma1 { > + status = "okay"; > +}; > + > +&gpi_dma2 { > + status = "okay"; > +}; > + > +&i2c_hub_2 { > + clock-frequency = <400000>; > + status = "okay"; > + > + pmic@75 { > + compatible = "dlg,slg51000"; > + reg = <0x75>; > + dlg,cs-gpios = <&pm8550vs_g_gpios 4 GPIO_ACTIVE_HIGH>; > + > + pinctrl-0 = <&cam_pwr_a_cs>; > + pinctrl-names = "default"; > + > + regulators { > + slg51000_a_ldo1: ldo1 { > + regulator-name = "slg51000_a_ldo1"; > + regulator-min-microvolt = <2400000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + slg51000_a_ldo2: ldo2 { > + regulator-name = "slg51000_a_ldo2"; > + regulator-min-microvolt = <2400000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + slg51000_a_ldo3: ldo3 { > + regulator-name = "slg51000_a_ldo3"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <3750000>; > + }; > + > + slg51000_a_ldo4: ldo4 { > + regulator-name = "slg51000_a_ldo4"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <3750000>; > + }; > + > + slg51000_a_ldo5: ldo5 { > + regulator-name = "slg51000_a_ldo5"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + slg51000_a_ldo6: ldo6 { > + regulator-name = "slg51000_a_ldo6"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + slg51000_a_ldo7: ldo7 { > + regulator-name = "slg51000_a_ldo7"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <3750000>; > + }; > + }; > + }; > +}; > + > +&i2c_master_hub_0 { > + status = "okay"; > +}; > + > +&i2c0 { > + clock-frequency = <1000000>; > + status = "okay"; > + > + /* NXP NFC @ 28 */ > +}; > + > +&i2c4 { > + clock-frequency = <400000>; > + status = "okay"; > + > + /* LX Semi SW82907 touchscreen @ 28 */ > +}; > + > +&i2c10 { > + clock-frequency = <1000000>; > + status = "okay"; > + > + /* Cirrus Logic CS40L25A boosted haptics driver @ 40 */ > +}; > + > +&i2c11 { > + clock-frequency = <1000000>; > + status = "okay"; > + > + cs35l41_l: speaker-amp@30 { > + compatible = "cirrus,cs35l45"; > + reg = <0x30>; > + interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>; > + reset-gpios = <&tlmm 183 GPIO_ACTIVE_HIGH>; > + cirrus,asp-sdout-hiz-ctrl = <(CS35L45_ASP_TX_HIZ_UNUSED | > CS35L45_ASP_TX_HIZ_DISABLED)>; > + #sound-dai-cells = <1>; > + > + cirrus,gpio-ctrl2 { > + gpio-ctrl = <0x2>; > + }; > + }; > + > + cs35l41_r: speaker-amp@31 { > + compatible = "cirrus,cs35l45"; > + reg = <0x31>; > + interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>; > + reset-gpios = <&tlmm 183 GPIO_ACTIVE_HIGH>; > + cirrus,asp-sdout-hiz-ctrl = <(CS35L45_ASP_TX_HIZ_UNUSED | > CS35L45_ASP_TX_HIZ_DISABLED)>; > + #sound-dai-cells = <1>; > + > + cirrus,gpio-ctrl2 { > + gpio-ctrl = <0x2>; > + }; > + }; > +}; > + > +&pcie0 { > + wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>; > + perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; > + > + pinctrl-0 = <&pcie0_default_state>; > + pinctrl-names = "default"; > + > + status = "okay"; > +}; > + > +&pcie0_phy { > + vdda-phy-supply = <&pm8550vs_2_l1>; > + vdda-pll-supply = <&pm8550vs_2_l3>; > + > + status = "okay"; > +}; > + > +&pm8550_flash { > + status = "okay"; > + > + led-0 { > + function = LED_FUNCTION_FLASH; > + color = <LED_COLOR_ID_WHITE>; > + led-sources = <1>, <4>; > + led-max-microamp = <500000>; > + flash-max-microamp = <1000000>; > + flash-max-timeout-us = <1280000>; > + function-enumerator = <0>; > + }; > + > + led-1 { > + function = LED_FUNCTION_FLASH; > + color = <LED_COLOR_ID_YELLOW>; > + led-sources = <2>, <3>; > + led-max-microamp = <500000>; > + flash-max-microamp = <1000000>; > + flash-max-timeout-us = <1280000>; > + function-enumerator = <1>; > + }; > +}; > + > +&pm8550_gpios { > + vol_down_n: volume-down-n-state { > + pins = "gpio6"; > + function = "normal"; > + power-source = <1>; > + bias-pull-up; > + input-enable; > + }; > + > + sdc2_card_det_n: sd-card-det-n-state { > + pins = "gpio12"; > + function = "normal"; > + power-source = <1>; > + bias-pull-down; > + output-disable; > + input-enable; > + }; > +}; > + > +&pm8550b_gpios { > + snapshot_n: snapshot-n-state { > + pins = "gpio7"; > + function = "normal"; > + power-source = <1>; > + bias-pull-up; > + input-enable; > + }; > + > + focus_n: focus-n-state { > + pins = "gpio8"; > + function = "normal"; > + power-source = <1>; > + bias-pull-up; > + input-enable; > + }; > +}; > + > +&pm8550vs_g_gpios { > + cam_pwr_a_cs: cam-pwr-a-cs-state { > + pins = "gpio4"; > + function = "normal"; > + power-source = <0x01>; > + drive-push-pull; > + output-low; > + qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; > + }; > +}; > + > +&pm8550b_eusb2_repeater { > + qcom,tune-usb2-disc-thres = /bits/ 8 <0x6>; > + qcom,tune-usb2-amplitude = /bits/ 8 <0xf>; > + qcom,tune-usb2-preem = /bits/ 8 <0x7>; > + vdd18-supply = <&pm8550_l15>; > + vdd3-supply = <&pm8550_l5>; > +}; > + > +&pon_pwrkey { > + status = "okay"; > +}; > + > +&pon_resin { > + linux,code = <KEY_VOLUMEUP>; > + status = "okay"; > +}; > + > +&qupv3_id_0 { > + status = "okay"; > +}; > + > +&qupv3_id_1 { > + status = "okay"; > +}; > + > +&remoteproc_adsp { > + firmware-name = "qcom/sm8550/Sony/yodo/adsp.mbn", > + "qcom/sm8550/Sony/yodo/adsp_dtb.mbn"; > + status = "okay"; > +}; > + > +&remoteproc_cdsp { > + firmware-name = "qcom/sm8550/Sony/yodo/cdsp.mbn", > + "qcom/sm8550/Sony/yodo/cdsp_dtb.mbn"; > + status = "okay"; > +}; > + > +&sdhc_2 { > + cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_HIGH>; > + pinctrl-0 = <&sdc2_default &sdc2_card_det_n>; > + pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>; > + pinctrl-names = "default", "sleep"; > + vmmc-supply = <&pm8550_l9>; > + vqmmc-supply = <&pm8550_l8>; > + no-sdio; > + no-mmc; > + status = "okay"; > +}; > + > +&sleep_clk { > + clock-frequency = <32000>; > +}; > + > +&tlmm { > + gpio-reserved-ranges = <32 8>; > +}; > + > +&uart7 { > + status = "okay"; > +}; > + > +&usb_1 { > + status = "okay"; > +}; > + > +&usb_1_dwc3 { > + dr_mode = "otg"; > + usb-role-switch; > +}; > + > +&usb_1_dwc3_hs { > + remote-endpoint = <&pmic_glink_hs_in>; > +}; > + > +&usb_1_dwc3_ss { > + remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>; > +}; > + > +&usb_1_hsphy { > + vdd-supply = <&pm8550vs_2_l1>; > + vdda12-supply = <&pm8550vs_2_l3>; > + phys = <&pm8550b_eusb2_repeater>; > + > + status = "okay"; > +}; > + > +&usb_dp_qmpphy { > + vdda-phy-supply = <&pm8550vs_2_l3>; > + vdda-pll-supply = <&pm8550ve_l3>; > + orientation-switch; > + > + status = "okay"; > +}; > + > +&usb_dp_qmpphy_out { > + remote-endpoint = <&pmic_glink_ss_in>; > +}; > + > +&usb_dp_qmpphy_usb_ss_in { > + remote-endpoint = <&usb_1_dwc3_ss>; > +}; > + > +&xo_board { > + clock-frequency = <76800000>; > +};
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index f7c5662213e4..9bbea531660d 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -237,6 +237,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx224.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8550-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8550-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8550-qrd.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8550-sony-xperia-yodo-pdx234.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb diff --git a/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts b/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts new file mode 100644 index 000000000000..85e0d3d66e16 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts @@ -0,0 +1,779 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2023, Linaro Limited + */ + +/dts-v1/; + +#include <dt-bindings/firmware/qcom,scm.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include <dt-bindings/sound/cs35l45.h> +#include "sm8550.dtsi" +#include "pm8010.dtsi" +#include "pm8550.dtsi" +#include "pm8550b.dtsi" +#define PMK8550VE_SID 5 +#include "pm8550ve.dtsi" +#include "pm8550vs.dtsi" +#include "pmk8550.dtsi" +/* TODO: Only one SID of PMR735D seems accessible? */ + +/delete-node/ &hwfence_shbuf; +/delete-node/ &mpss_mem; +/delete-node/ &rmtfs_mem; +/ { + model = "Sony Xperia 1 V"; + compatible = "sony,pdx234", "qcom,sm8550"; + chassis-type = "handset"; + + aliases { + i2c0 = &i2c0; + i2c4 = &i2c4; + i2c10 = &i2c10; + i2c11 = &i2c11; + i2c16 = &i2c_hub_2; + serial0 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + label = "gpio-keys"; + + pinctrl-0 = <&focus_n &snapshot_n &vol_down_n>; + pinctrl-names = "default"; + + key-camera-focus { + label = "Camera Focus"; + linux,code = <KEY_CAMERA_FOCUS>; + gpios = <&pm8550b_gpios 8 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + linux,can-disable; + wakeup-source; + }; + + key-camera-snapshot { + label = "Camera Snapshot"; + gpios = <&pm8550b_gpios 7 GPIO_ACTIVE_LOW>; + linux,code = <KEY_CAMERA>; + debounce-interval = <15>; + linux,can-disable; + wakeup-source; + }; + + key-volume-down { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + linux,can-disable; + wakeup-source; + }; + }; + + pmic-glink { + compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink"; + orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_hs_in: endpoint { + remote-endpoint = <&usb_1_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss_in: endpoint { + remote-endpoint = <&usb_dp_qmpphy_out>; + }; + }; + }; + }; + }; + + reserved-memory { + mpss_mem: mpss-region@89800000 { + reg = <0x0 0x89800000 0x0 0x10800000>; + no-map; + }; + + splash@b8000000 { + reg = <0x0 0xb8000000 0x0 0x2b00000>; + no-map; + }; + + hwfence_shbuf: hwfence-shbuf-region@e6440000 { + reg = <0x0 0xe6440000 0x0 0x2dd000>; + no-map; + }; + + rmtfs_mem: memory@f8b00000 { + compatible = "qcom,rmtfs-mem"; + reg = <0x0 0xf8b00000 0x0 0x280000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>; + }; + + ramoops@ffd00000 { + compatible = "ramoops"; + reg = <0x0 0xffd00000 0x0 0xc0000>; + console-size = <0x40000>; + record-size = <0x1000>; + pmsg-size = <0x40000>; + ecc-size = <16>; + }; + + rdtag-store-region@ffdc0000 { + reg = <0x0 0xffdc0000 0x0 0x40000>; + no-map; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8550-rpmh-regulators"; + qcom,pmic-id = "b"; + + pm8550_bob1: bob1 { + regulator-name = "pm8550_bob1"; + regulator-min-microvolt = <3416000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + /* TODO: bob2 @ 2.704-3.008V doesn't fall into the vreg driver constraints */ + + pm8550_l1: ldo1 { + regulator-name = "pm8550_l1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l2: ldo2 { + regulator-name = "pm8550_l2"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + /* L4 exists in cmd-db, but the board seems to crash on access */ + + pm8550_l5: ldo5 { + regulator-name = "pm8550_l5"; + regulator-min-microvolt = <3104000>; + regulator-max-microvolt = <3104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l6: ldo6 { + regulator-name = "pm8550_l6"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l7: ldo7 { + regulator-name = "pm8550_l7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l8: ldo8 { + regulator-name = "pm8550_l8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l9: ldo9 { + regulator-name = "pm8550_l9"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l10: ldo10 { + regulator-name = "pm8550_l10"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l11: ldo11 { + regulator-name = "pm8550_l11"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l12: ldo12 { + regulator-name = "pm8550_l12"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l13: ldo13 { + regulator-name = "pm8550_l13"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l14: ldo14 { + regulator-name = "pm8550_l14"; + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l15: ldo15 { + regulator-name = "pm8550_l15"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l16: ldo16 { + regulator-name = "pm8550_l16"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550_l17: ldo17 { + regulator-name = "pm8550_l17"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8550vs-rpmh-regulators"; + qcom,pmic-id = "c"; + + pm8550vs_0_l1: ldo1 { + regulator-name = "pm8550vs_0_l1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_0_l3: ldo3 { + regulator-name = "pm8550vs_0_l3"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pm8550vs-rpmh-regulators"; + qcom,pmic-id = "d"; + + pm8550vs_1_l1: ldo1 { + regulator-name = "pm8550vs_1_l1"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + /* L3 exists in cmd-db, but the board seems to crash on access */ + }; + + regulators-3 { + compatible = "qcom,pm8550vs-rpmh-regulators"; + qcom,pmic-id = "e"; + + pm8550vs_2_s4: smps4 { + regulator-name = "pm8550vs_2_s4"; + regulator-min-microvolt = <904000>; + regulator-max-microvolt = <984000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_2_s5: smps5 { + regulator-name = "pm8550vs_2_s5"; + regulator-min-microvolt = <1010000>; + regulator-max-microvolt = <1120000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_2_l1: ldo1 { + regulator-name = "pm8550vs_2_l1"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_2_l2: ldo2 { + regulator-name = "pm8550vs_2_l2"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <968000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_2_l3: ldo3 { + regulator-name = "pm8550vs_2_l3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-4 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "f"; + + pm8550ve_s4: smps4 { + regulator-name = "pm8550ve_s4"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <700000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550ve_l1: ldo1 { + regulator-name = "pm8550ve_l1"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550ve_l2: ldo2 { + regulator-name = "pm8550ve_l2"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550ve_l3: ldo3 { + regulator-name = "pm8550ve_l3"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-5 { + compatible = "qcom,pm8550vs-rpmh-regulators"; + qcom,pmic-id = "g"; + + pm8550vs_3_s1: smps1 { + regulator-name = "pm8550vs_3_s1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_3_s2: smps2 { + regulator-name = "pm8550vs_3_s2"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1036000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_3_s3: smps3 { + regulator-name = "pm8550vs_3_s3"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1004000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_3_s4: smps4 { + regulator-name = "pm8550vs_3_s4"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1352000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_3_s5: smps5 { + regulator-name = "pm8550vs_3_s5"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1004000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_3_s6: smps6 { + regulator-name = "pm8550vs_3_s6"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_3_l1: ldo1 { + regulator-name = "pm8550vs_3_l1"; + regulator-min-microvolt = <1144000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_3_l2: ldo2 { + regulator-name = "pm8550vs_3_l2"; + regulator-min-microvolt = <1104000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pm8550vs_3_l3: ldo3 { + regulator-name = "pm8550vs_3_l3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + /* TODO: Unknown PMIC @ k, l, PM8010 @ m, n */ +}; + +&gpi_dma1 { + status = "okay"; +}; + +&gpi_dma2 { + status = "okay"; +}; + +&i2c_hub_2 { + clock-frequency = <400000>; + status = "okay"; + + pmic@75 { + compatible = "dlg,slg51000"; + reg = <0x75>; + dlg,cs-gpios = <&pm8550vs_g_gpios 4 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&cam_pwr_a_cs>; + pinctrl-names = "default"; + + regulators { + slg51000_a_ldo1: ldo1 { + regulator-name = "slg51000_a_ldo1"; + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3300000>; + }; + + slg51000_a_ldo2: ldo2 { + regulator-name = "slg51000_a_ldo2"; + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3300000>; + }; + + slg51000_a_ldo3: ldo3 { + regulator-name = "slg51000_a_ldo3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3750000>; + }; + + slg51000_a_ldo4: ldo4 { + regulator-name = "slg51000_a_ldo4"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3750000>; + }; + + slg51000_a_ldo5: ldo5 { + regulator-name = "slg51000_a_ldo5"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1200000>; + }; + + slg51000_a_ldo6: ldo6 { + regulator-name = "slg51000_a_ldo6"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1200000>; + }; + + slg51000_a_ldo7: ldo7 { + regulator-name = "slg51000_a_ldo7"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3750000>; + }; + }; + }; +}; + +&i2c_master_hub_0 { + status = "okay"; +}; + +&i2c0 { + clock-frequency = <1000000>; + status = "okay"; + + /* NXP NFC @ 28 */ +}; + +&i2c4 { + clock-frequency = <400000>; + status = "okay"; + + /* LX Semi SW82907 touchscreen @ 28 */ +}; + +&i2c10 { + clock-frequency = <1000000>; + status = "okay"; + + /* Cirrus Logic CS40L25A boosted haptics driver @ 40 */ +}; + +&i2c11 { + clock-frequency = <1000000>; + status = "okay"; + + cs35l41_l: speaker-amp@30 { + compatible = "cirrus,cs35l45"; + reg = <0x30>; + interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&tlmm 183 GPIO_ACTIVE_HIGH>; + cirrus,asp-sdout-hiz-ctrl = <(CS35L45_ASP_TX_HIZ_UNUSED | CS35L45_ASP_TX_HIZ_DISABLED)>; + #sound-dai-cells = <1>; + + cirrus,gpio-ctrl2 { + gpio-ctrl = <0x2>; + }; + }; + + cs35l41_r: speaker-amp@31 { + compatible = "cirrus,cs35l45"; + reg = <0x31>; + interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&tlmm 183 GPIO_ACTIVE_HIGH>; + cirrus,asp-sdout-hiz-ctrl = <(CS35L45_ASP_TX_HIZ_UNUSED | CS35L45_ASP_TX_HIZ_DISABLED)>; + #sound-dai-cells = <1>; + + cirrus,gpio-ctrl2 { + gpio-ctrl = <0x2>; + }; + }; +}; + +&pcie0 { + wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>; + perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&pcie0_default_state>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie0_phy { + vdda-phy-supply = <&pm8550vs_2_l1>; + vdda-pll-supply = <&pm8550vs_2_l3>; + + status = "okay"; +}; + +&pm8550_flash { + status = "okay"; + + led-0 { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_WHITE>; + led-sources = <1>, <4>; + led-max-microamp = <500000>; + flash-max-microamp = <1000000>; + flash-max-timeout-us = <1280000>; + function-enumerator = <0>; + }; + + led-1 { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_YELLOW>; + led-sources = <2>, <3>; + led-max-microamp = <500000>; + flash-max-microamp = <1000000>; + flash-max-timeout-us = <1280000>; + function-enumerator = <1>; + }; +}; + +&pm8550_gpios { + vol_down_n: volume-down-n-state { + pins = "gpio6"; + function = "normal"; + power-source = <1>; + bias-pull-up; + input-enable; + }; + + sdc2_card_det_n: sd-card-det-n-state { + pins = "gpio12"; + function = "normal"; + power-source = <1>; + bias-pull-down; + output-disable; + input-enable; + }; +}; + +&pm8550b_gpios { + snapshot_n: snapshot-n-state { + pins = "gpio7"; + function = "normal"; + power-source = <1>; + bias-pull-up; + input-enable; + }; + + focus_n: focus-n-state { + pins = "gpio8"; + function = "normal"; + power-source = <1>; + bias-pull-up; + input-enable; + }; +}; + +&pm8550vs_g_gpios { + cam_pwr_a_cs: cam-pwr-a-cs-state { + pins = "gpio4"; + function = "normal"; + power-source = <0x01>; + drive-push-pull; + output-low; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; + }; +}; + +&pm8550b_eusb2_repeater { + qcom,tune-usb2-disc-thres = /bits/ 8 <0x6>; + qcom,tune-usb2-amplitude = /bits/ 8 <0xf>; + qcom,tune-usb2-preem = /bits/ 8 <0x7>; + vdd18-supply = <&pm8550_l15>; + vdd3-supply = <&pm8550_l5>; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + linux,code = <KEY_VOLUMEUP>; + status = "okay"; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/sm8550/Sony/yodo/adsp.mbn", + "qcom/sm8550/Sony/yodo/adsp_dtb.mbn"; + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/sm8550/Sony/yodo/cdsp.mbn", + "qcom/sm8550/Sony/yodo/cdsp_dtb.mbn"; + status = "okay"; +}; + +&sdhc_2 { + cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&sdc2_default &sdc2_card_det_n>; + pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>; + pinctrl-names = "default", "sleep"; + vmmc-supply = <&pm8550_l9>; + vqmmc-supply = <&pm8550_l8>; + no-sdio; + no-mmc; + status = "okay"; +}; + +&sleep_clk { + clock-frequency = <32000>; +}; + +&tlmm { + gpio-reserved-ranges = <32 8>; +}; + +&uart7 { + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "otg"; + usb-role-switch; +}; + +&usb_1_dwc3_hs { + remote-endpoint = <&pmic_glink_hs_in>; +}; + +&usb_1_dwc3_ss { + remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>; +}; + +&usb_1_hsphy { + vdd-supply = <&pm8550vs_2_l1>; + vdda12-supply = <&pm8550vs_2_l3>; + phys = <&pm8550b_eusb2_repeater>; + + status = "okay"; +}; + +&usb_dp_qmpphy { + vdda-phy-supply = <&pm8550vs_2_l3>; + vdda-pll-supply = <&pm8550ve_l3>; + orientation-switch; + + status = "okay"; +}; + +&usb_dp_qmpphy_out { + remote-endpoint = <&pmic_glink_ss_in>; +}; + +&usb_dp_qmpphy_usb_ss_in { + remote-endpoint = <&usb_1_dwc3_ss>; +}; + +&xo_board { + clock-frequency = <76800000>; +};
Add support for Sony Xperia 1 V, a.k.a PDX234. This device is a part of the SoMC SM8550 Yodo platform. This commit brings support for: * Remoteprocs (sans modem for now) * Flash LED (the notification LED is gone :((((() * SD Card * USB (*including SuperSpeed*) + PMIC_GLINK (it's funky, requires a replug with an cable flip sometimes..) * Most regulators * Part of I2C-connected peripherals (notably no touch due to a driver bug) * PCIe0 (PCIe1 is unused) Do note display via simplefb is not supported, as the display is blanked upon exiting XBL. To create a working boot image, you need to run: cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/sm8550-sony-xperia-\ yodo-pdx234.dtb > .Image.gz-dtb mkbootimg \ --kernel .Image.gz-dtb \ --ramdisk some_initrd.img \ --pagesize 4096 \ --base 0x0 \ --kernel_offset 0x8000 \ --ramdisk_offset 0x1000000 \ --tags_offset 0x100 \ --cmdline "SOME_CMDLINE" \ --dtb_offset 0x1f00000 \ --header_version 2 \ -o boot.img-sony-xperia-pdx234 Then, you need to flash it on the device and get rid of all the vendor_boot/dtbo mess: // You have to either pull vbmeta{"","_system"} from // /dev/block/bootdevice/by-name/ or build one as a part of AOSP build process fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img fastboot --disable-verity --disable-verification flash vbmeta_system \ vbmeta_system.img fastboot flash boot boot.img-sony-xperia-pdx234 fastboot erase vendor_boot fastboot erase recovery fastboot flash dtbo emptydtbo.img fastboot erase init_boot // ? I don't remember if it's necessary, sorry fastboot continue Where emptydtbo.img is a tiny file that consists of 2 bytes (all zeroes), doing a "fastboot erase" won't cut it, the bootloader will go crazy and things will fall apart when it tries to overlay random bytes from an empty partition onto a perfectly good appended DTB. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts | 779 +++++++++++++++++++++ 2 files changed, 780 insertions(+)