diff --git a/drivers/net/ethernet/qualcomm/Kconfig b/drivers/net/ethernet/qualcomm/Kconfig
index 9210ff360fdc..59931c4edbeb 100644
--- a/drivers/net/ethernet/qualcomm/Kconfig
+++ b/drivers/net/ethernet/qualcomm/Kconfig
@@ -61,6 +61,21 @@ config QCOM_EMAC
 	  low power, Receive-Side Scaling (RSS), and IEEE 1588-2008
 	  Precision Clock Synchronization Protocol.
 
+config QCOM_PPE
+	tristate "Qualcomm Technologies, Inc. PPE Ethernet support"
+	depends on HAS_IOMEM && OF
+	depends on COMMON_CLK
+	select REGMAP_MMIO
+	help
+	  This driver supports the Qualcomm Technologies, Inc. packet
+	  process engine (PPE) available with IPQ SoC. The PPE includes
+	  the ethernet MACs, Ethernet DMA (EDMA) and switch core that
+	  supports L3 flow offload, L2 switch function, RSS and tunnel
+	  offload.
+
+	  To compile this driver as a module, choose M here. The module
+	  will be called qcom-ppe.
+
 source "drivers/net/ethernet/qualcomm/rmnet/Kconfig"
 
 endif # NET_VENDOR_QUALCOMM
diff --git a/drivers/net/ethernet/qualcomm/Makefile b/drivers/net/ethernet/qualcomm/Makefile
index 9250976dd884..166a59aea363 100644
--- a/drivers/net/ethernet/qualcomm/Makefile
+++ b/drivers/net/ethernet/qualcomm/Makefile
@@ -11,4 +11,5 @@ qcauart-objs := qca_uart.o
 
 obj-y += emac/
 
+obj-$(CONFIG_QCOM_PPE) += ppe/
 obj-$(CONFIG_RMNET) += rmnet/
diff --git a/drivers/net/ethernet/qualcomm/ppe/Makefile b/drivers/net/ethernet/qualcomm/ppe/Makefile
new file mode 100644
index 000000000000..63d50d3b4f2e
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/ppe/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the device driver of PPE (Packet Process Engine) in IPQ SoC
+#
+
+obj-$(CONFIG_QCOM_PPE) += qcom-ppe.o
+qcom-ppe-objs := ppe.o
diff --git a/drivers/net/ethernet/qualcomm/ppe/ppe.c b/drivers/net/ethernet/qualcomm/ppe/ppe.c
new file mode 100644
index 000000000000..4d90fcb8fa43
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/ppe/ppe.c
@@ -0,0 +1,218 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/* PPE platform device probe, DTSI parser and PPE clock initializations. */
+
+#include <linux/clk.h>
+#include <linux/interconnect.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include "ppe.h"
+
+#define PPE_PORT_MAX		8
+#define PPE_CLK_RATE		353000000
+
+/* ICC clocks for enabling PPE device. The avg_bw and peak_bw with value 0
+ * will be updated by the clock rate of PPE.
+ */
+static const struct icc_bulk_data ppe_icc_data[] = {
+	{
+		.name = "ppe",
+		.avg_bw = 0,
+		.peak_bw = 0,
+	},
+	{
+		.name = "ppe_cfg",
+		.avg_bw = 0,
+		.peak_bw = 0,
+	},
+	{
+		.name = "qos_gen",
+		.avg_bw = 6000,
+		.peak_bw = 6000,
+	},
+	{
+		.name = "timeout_ref",
+		.avg_bw = 6000,
+		.peak_bw = 6000,
+	},
+	{
+		.name = "nssnoc_memnoc",
+		.avg_bw = 533333,
+		.peak_bw = 533333,
+	},
+	{
+		.name = "memnoc_nssnoc",
+		.avg_bw = 533333,
+		.peak_bw = 533333,
+	},
+	{
+		.name = "memnoc_nssnoc_1",
+		.avg_bw = 533333,
+		.peak_bw = 533333,
+	},
+};
+
+static const struct regmap_range ppe_readable_ranges[] = {
+	regmap_reg_range(0x0, 0x1ff),		/* Global */
+	regmap_reg_range(0x400, 0x5ff),		/* LPI CSR */
+	regmap_reg_range(0x1000, 0x11ff),	/* GMAC0 */
+	regmap_reg_range(0x1200, 0x13ff),	/* GMAC1 */
+	regmap_reg_range(0x1400, 0x15ff),	/* GMAC2 */
+	regmap_reg_range(0x1600, 0x17ff),	/* GMAC3 */
+	regmap_reg_range(0x1800, 0x19ff),	/* GMAC4 */
+	regmap_reg_range(0x1a00, 0x1bff),	/* GMAC5 */
+	regmap_reg_range(0xb000, 0xefff),	/* PRX CSR */
+	regmap_reg_range(0xf000, 0x1efff),	/* IPE */
+	regmap_reg_range(0x20000, 0x5ffff),	/* PTX CSR */
+	regmap_reg_range(0x60000, 0x9ffff),	/* IPE L2 CSR */
+	regmap_reg_range(0xb0000, 0xeffff),	/* IPO CSR */
+	regmap_reg_range(0x100000, 0x17ffff),	/* IPE PC */
+	regmap_reg_range(0x180000, 0x1bffff),	/* PRE IPO CSR */
+	regmap_reg_range(0x1d0000, 0x1dffff),	/* Tunnel parser */
+	regmap_reg_range(0x1e0000, 0x1effff),	/* Ingress parse */
+	regmap_reg_range(0x200000, 0x2fffff),	/* IPE L3 */
+	regmap_reg_range(0x300000, 0x3fffff),	/* IPE tunnel */
+	regmap_reg_range(0x400000, 0x4fffff),	/* Scheduler */
+	regmap_reg_range(0x500000, 0x503fff),	/* XGMAC0 */
+	regmap_reg_range(0x504000, 0x507fff),	/* XGMAC1 */
+	regmap_reg_range(0x508000, 0x50bfff),	/* XGMAC2 */
+	regmap_reg_range(0x50c000, 0x50ffff),	/* XGMAC3 */
+	regmap_reg_range(0x510000, 0x513fff),	/* XGMAC4 */
+	regmap_reg_range(0x514000, 0x517fff),	/* XGMAC5 */
+	regmap_reg_range(0x600000, 0x6fffff),	/* BM */
+	regmap_reg_range(0x800000, 0x9fffff),	/* QM */
+	regmap_reg_range(0xb00000, 0xbef800),	/* EDMA */
+};
+
+static const struct regmap_access_table ppe_reg_table = {
+	.yes_ranges = ppe_readable_ranges,
+	.n_yes_ranges = ARRAY_SIZE(ppe_readable_ranges),
+};
+
+static const struct regmap_config regmap_config_ipq9574 = {
+	.reg_bits = 32,
+	.reg_stride = 4,
+	.val_bits = 32,
+	.rd_table = &ppe_reg_table,
+	.wr_table = &ppe_reg_table,
+	.max_register = 0xbef800,
+	.fast_io = true,
+};
+
+static int ppe_clock_init_and_reset(struct ppe_device *ppe_dev)
+{
+	unsigned long ppe_rate = ppe_dev->clk_rate;
+	struct device *dev = ppe_dev->dev;
+	struct reset_control *rstc;
+	struct clk_bulk_data *clks;
+	struct clk *clk;
+	int ret, i;
+
+	for (i = 0; i < ppe_dev->num_icc_paths; i++) {
+		ppe_dev->icc_paths[i].name = ppe_icc_data[i].name;
+		ppe_dev->icc_paths[i].avg_bw = ppe_icc_data[i].avg_bw ? :
+					       Bps_to_icc(ppe_rate);
+		ppe_dev->icc_paths[i].peak_bw = ppe_icc_data[i].peak_bw ? :
+						Bps_to_icc(ppe_rate);
+	}
+
+	ret = devm_of_icc_bulk_get(dev, ppe_dev->num_icc_paths,
+				   ppe_dev->icc_paths);
+	if (ret)
+		return ret;
+
+	ret = icc_bulk_set_bw(ppe_dev->num_icc_paths, ppe_dev->icc_paths);
+	if (ret)
+		return ret;
+
+	/* The PPE clocks have a common parent clock. Setting the clock
+	 * rate of "ppe" ensures the clock rate of all PPE clocks is
+	 * configured to the same rate.
+	 */
+	clk = devm_clk_get(dev, "ppe");
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	ret = clk_set_rate(clk, ppe_rate);
+	if (ret)
+		return ret;
+
+	ret = devm_clk_bulk_get_all_enable(dev, &clks);
+	if (ret < 0)
+		return ret;
+
+	/* Reset the PPE. */
+	rstc = devm_reset_control_get_exclusive(dev, NULL);
+	if (IS_ERR(rstc))
+		return PTR_ERR(rstc);
+
+	ret = reset_control_assert(rstc);
+	if (ret)
+		return ret;
+
+	/* The delay 10 ms of assert is necessary for resetting PPE. */
+	usleep_range(10000, 11000);
+
+	return reset_control_deassert(rstc);
+}
+
+static int qcom_ppe_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ppe_device *ppe_dev;
+	void __iomem *base;
+	int ret, num_icc;
+
+	num_icc = ARRAY_SIZE(ppe_icc_data);
+	ppe_dev = devm_kzalloc(dev, struct_size(ppe_dev, icc_paths, num_icc),
+			       GFP_KERNEL);
+	if (!ppe_dev)
+		return dev_err_probe(dev, -ENOMEM, "PPE alloc memory failed\n");
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return dev_err_probe(dev, PTR_ERR(base), "PPE ioremap failed\n");
+
+	ppe_dev->regmap = devm_regmap_init_mmio(dev, base, &regmap_config_ipq9574);
+	if (IS_ERR(ppe_dev->regmap))
+		return dev_err_probe(dev, PTR_ERR(ppe_dev->regmap),
+				     "PPE initialize regmap failed\n");
+	ppe_dev->dev = dev;
+	ppe_dev->clk_rate = PPE_CLK_RATE;
+	ppe_dev->num_ports = PPE_PORT_MAX;
+	ppe_dev->num_icc_paths = num_icc;
+
+	ret = ppe_clock_init_and_reset(ppe_dev);
+	if (ret)
+		return dev_err_probe(dev, ret, "PPE clock config failed\n");
+
+	platform_set_drvdata(pdev, ppe_dev);
+
+	return 0;
+}
+
+static const struct of_device_id qcom_ppe_of_match[] = {
+	{ .compatible = "qcom,ipq9574-ppe" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, qcom_ppe_of_match);
+
+static struct platform_driver qcom_ppe_driver = {
+	.driver = {
+		.name = "qcom_ppe",
+		.of_match_table = qcom_ppe_of_match,
+	},
+	.probe	= qcom_ppe_probe,
+};
+module_platform_driver(qcom_ppe_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Qualcomm Technologies, Inc. IPQ PPE driver");
diff --git a/drivers/net/ethernet/qualcomm/ppe/ppe.h b/drivers/net/ethernet/qualcomm/ppe/ppe.h
new file mode 100644
index 000000000000..cc6767b7c2b8
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/ppe/ppe.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0-only
+ *
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#ifndef __PPE_H__
+#define __PPE_H__
+
+#include <linux/compiler.h>
+#include <linux/interconnect.h>
+
+struct device;
+struct regmap;
+
+/**
+ * struct ppe_device - PPE device private data.
+ * @dev: PPE device structure.
+ * @regmap: PPE register map.
+ * @clk_rate: PPE clock rate.
+ * @num_ports: Number of PPE ports.
+ * @num_icc_paths: Number of interconnect paths.
+ * @icc_paths: Interconnect path array.
+ *
+ * PPE device is the instance of PPE hardware, which is used to
+ * configure PPE packet process modules such as BM (buffer management),
+ * QM (queue management), and scheduler.
+ */
+struct ppe_device {
+	struct device *dev;
+	struct regmap *regmap;
+	unsigned long clk_rate;
+	unsigned int num_ports;
+	unsigned int num_icc_paths;
+	struct icc_bulk_data icc_paths[] __counted_by(num_icc_paths);
+};
+#endif
