[1/2] hwmon: (sch5627) Disallow write access if virtual registers are locked

Commit Message

Armin Wolf Aug. 15, 2023, 4:55 p.m. UTC

When the lock bit inside SCH5627_REG_CTRL is set, then the virtual
registers become read-only until the next power cycle.
Disallow write access to those registers in such a case.

Tested on a Fujitsu Esprimo P720.

Fixes: aa9f833dfc12 ("hwmon: (sch5627) Add pwmX_auto_channels_temp support")
Signed-off-by: Armin Wolf <[e-mail]>
---
 drivers/hwmon/sch5627.c | 21 +++++++++++++++++----
 1 file changed, 17 insertions(+), 4 deletions(-)

--
2.39.2

Patch

diff --git a/drivers/hwmon/sch5627.c b/drivers/hwmon/sch5627.c
index 1bbda3b05532..bf408e35e2c3 100644
--- a/drivers/hwmon/sch5627.c
+++ b/drivers/hwmon/sch5627.c
@@ -6,6 +6,7 @@ 

 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

+#include <linux/bits.h>
 #include <linux/module.h>
 #include <linux/mod_devicetable.h>
 #include <linux/init.h>
@@ -32,6 +33,10 @@ 
 #define SCH5627_REG_PRIMARY_ID		0x3f
 #define SCH5627_REG_CTRL		0x40

+#define SCH5627_CTRL_START		BIT(0)
+#define SCH5627_CTRL_LOCK		BIT(1)
+#define SCH5627_CTRL_VBAT		BIT(4)
+
 #define SCH5627_NO_TEMPS		8
 #define SCH5627_NO_FANS			4
 #define SCH5627_NO_IN			5
@@ -147,7 +152,8 @@  static int sch5627_update_in(struct sch5627_data *data)

 	/* Trigger a Vbat voltage measurement every 5 minutes */
 	if (time_after(jiffies, data->last_battery + 300 * HZ)) {
-		sch56xx_write_virtual_reg(data->addr, SCH5627_REG_CTRL, data->control | 0x10);
+		sch56xx_write_virtual_reg(data->addr, SCH5627_REG_CTRL,
+					  data->control | SCH5627_CTRL_VBAT);
 		data->last_battery = jiffies;
 	}

@@ -226,6 +232,14 @@  static int reg_to_rpm(u16 reg)
 static umode_t sch5627_is_visible(const void *drvdata, enum hwmon_sensor_types type, u32 attr,
 				  int channel)
 {
+	const struct sch5627_data *data = drvdata;
+
+	/* Once the lock bit is set, the virtual registers become read-only
+	 * until the next power cycle.
+	 */
+	if (data->control & SCH5627_CTRL_LOCK)
+		return 0444;
+
 	if (type == hwmon_pwm && attr == hwmon_pwm_auto_channels_temp)
 		return 0644;

@@ -483,14 +497,13 @@  static int sch5627_probe(struct platform_device *pdev)
 		return val;

 	data->control = val;
-	if (!(data->control & 0x01)) {
+	if (!(data->control & SCH5627_CTRL_START)) {
 		pr_err("hardware monitoring not enabled\n");
 		return -ENODEV;
 	}
 	/* Trigger a Vbat voltage measurement, so that we get a valid reading
 	   the first time we read Vbat */
-	sch56xx_write_virtual_reg(data->addr, SCH5627_REG_CTRL,
-				  data->control | 0x10);
+	sch56xx_write_virtual_reg(data->addr, SCH5627_REG_CTRL, data->control | SCH5627_CTRL_VBAT);
 	data->last_battery = jiffies;

 	/*