@@ -1,6 +1,12 @@
+Kernel driver da9052
+====================
+
Supported chips:
+
* Dialog Semiconductors DA9052-BC and DA9053-AA/Bx PMICs
+
Prefix: 'da9052'
+
Datasheet: Datasheet is not publicly available.
Authors: David Dajun Chen <dchen@diasemi.com>
@@ -15,17 +21,20 @@ different inputs. The track and hold circuit ensures stable input voltages at
the input of the ADC during the conversion.
The ADC is used to measure the following inputs:
-Channel 0: VDDOUT - measurement of the system voltage
-Channel 1: ICH - internal battery charger current measurement
-Channel 2: TBAT - output from the battery NTC
-Channel 3: VBAT - measurement of the battery voltage
-Channel 4: ADC_IN4 - high impedance input (0 - 2.5V)
-Channel 5: ADC_IN5 - high impedance input (0 - 2.5V)
-Channel 6: ADC_IN6 - high impedance input (0 - 2.5V)
-Channel 7: XY - TSI interface to measure the X and Y voltage of the touch
- screen resistive potentiometers
-Channel 8: Internal Tjunc. - sense (internal temp. sensor)
-Channel 9: VBBAT - measurement of the backup battery voltage
+
+========= ===================================================================
+Channel 0 VDDOUT - measurement of the system voltage
+Channel 1 ICH - internal battery charger current measurement
+Channel 2 TBAT - output from the battery NTC
+Channel 3 VBAT - measurement of the battery voltage
+Channel 4 ADC_IN4 - high impedance input (0 - 2.5V)
+Channel 5 ADC_IN5 - high impedance input (0 - 2.5V)
+Channel 6 ADC_IN6 - high impedance input (0 - 2.5V)
+Channel 7 XY - TSI interface to measure the X and Y voltage of the touch
+ screen resistive potentiometers
+Channel 8 Internal Tjunc. - sense (internal temp. sensor)
+Channel 9 VBBAT - measurement of the backup battery voltage
+========= ===================================================================
By using sysfs attributes we can measure the system voltage VDDOUT, the battery
charging current ICH, battery temperature TBAT, battery junction temperature
@@ -37,12 +46,15 @@ Voltage Monitoring
Voltages are sampled by a 10 bit ADC.
The battery voltage is calculated as:
+
Milli volt = ((ADC value * 1000) / 512) + 2500
The backup battery voltage is calculated as:
+
Milli volt = (ADC value * 2500) / 512;
The voltages on ADC channels 4, 5 and 6 are calculated as:
+
Milli volt = (ADC value * 2500) / 1023
Temperature Monitoring
@@ -52,10 +64,15 @@ Temperatures are sampled by a 10 bit ADC. Junction and battery temperatures
are monitored by the ADC channels.
The junction temperature is calculated:
+
Degrees celsius = 1.708 * (TJUNC_RES - T_OFFSET) - 108.8
+
The junction temperature attribute is supported by the driver.
The battery temperature is calculated:
- Degree Celsius = 1 / (t1 + 1/298)- 273
+
+ Degree Celsius = 1 / (t1 + 1/298) - 273
+
where t1 = (1/B)* ln(( ADCval * 2.5)/(R25*ITBAT*255))
+
Default values of R25, B, ITBAT are 10e3, 3380 and 50e-6 respectively.
@@ -1,6 +1,11 @@
+Kernel driver da9055
+====================
+
Supported chips:
* Dialog Semiconductors DA9055 PMIC
+
Prefix: 'da9055'
+
Datasheet: Datasheet is not publicly available.
Authors: David Dajun Chen <dchen@diasemi.com>
@@ -15,11 +20,12 @@ different inputs. The track and hold circuit ensures stable input voltages at
the input of the ADC during the conversion.
The ADC is used to measure the following inputs:
-Channel 0: VDDOUT - measurement of the system voltage
-Channel 1: ADC_IN1 - high impedance input (0 - 2.5V)
-Channel 2: ADC_IN2 - high impedance input (0 - 2.5V)
-Channel 3: ADC_IN3 - high impedance input (0 - 2.5V)
-Channel 4: Internal Tjunc. - sense (internal temp. sensor)
+
+- Channel 0: VDDOUT - measurement of the system voltage
+- Channel 1: ADC_IN1 - high impedance input (0 - 2.5V)
+- Channel 2: ADC_IN2 - high impedance input (0 - 2.5V)
+- Channel 3: ADC_IN3 - high impedance input (0 - 2.5V)
+- Channel 4: Internal Tjunc. - sense (internal temp. sensor)
By using sysfs attributes we can measure the system voltage VDDOUT,
chip junction temperature and auxiliary channels voltages.
@@ -31,9 +37,11 @@ Voltages are sampled in a AUTO mode it can be manually sampled too and results
are stored in a 10 bit ADC.
The system voltage is calculated as:
+
Milli volt = ((ADC value * 1000) / 85) + 2500
The voltages on ADC channels 1, 2 and 3 are calculated as:
+
Milli volt = (ADC value * 1000) / 102
Temperature Monitoring
@@ -43,5 +51,7 @@ Temperatures are sampled by a 10 bit ADC. Junction temperatures
are monitored by the ADC channels.
The junction temperature is calculated:
+
Degrees celsius = -0.4084 * (ADC_RES - T_OFFSET) + 307.6332
+
The junction temperature attribute is supported by the driver.
Convert da9052 and da9055 to ReST format, in order to allow them to be parsed by Sphinx. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> --- Documentation/hwmon/da9052 | 41 +++++++++++++++++++++++++++----------- Documentation/hwmon/da9055 | 20 ++++++++++++++----- 2 files changed, 44 insertions(+), 17 deletions(-)