| Message ID | 1536909510-7166-2-git-send-email-manish.narani@xilinx.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add Xilinx AMS Driver | expand |
> Xilinx AMS have several ADC channels that can be used for measurement of > different voltages and temperatures. Document the same in the bindings. minor comments below > Signed-off-by: Manish Narani <manish.narani@xilinx.com> > --- > .../devicetree/bindings/iio/adc/xilinx-ams.txt | 180 +++++++++++++++++++++ > 1 file changed, 180 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/adc/xilinx-ams.txt > > diff --git a/Documentation/devicetree/bindings/iio/adc/xilinx-ams.txt b/Documentation/devicetree/bindings/iio/adc/xilinx-ams.txt > new file mode 100644 > index 0000000..d0958a1 > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/adc/xilinx-ams.txt > @@ -0,0 +1,180 @@ > +Xilinx AMS controller > +````````````````````` > +The AMS includes an ADC as well as on-chip sensors that can be used to > +sample external voltages and monitor on-die operating conditions, such as > +temperature and supply voltage levels. > +The AMS has two SYSMON blocks which are PL (Programmable Logic) SYSMON and > +PS (Processing System) SYSMON. > +All designs should have AMS registers, but PS and PL are optional. The > +AMS controller can work with only PS, only PL and both PS and PL > +configurations. Please specify registers according to your design. Devicetree > +should always have AMS module property. Providing PS & PL module is optional. > + > +Required properties: > + - compatible: Should be "xlnx,zynqmp-ams" > + - reg: Should specify AMS register space > + - interrupts: Interrupt number for the AMS control interface > + - interrupt-names: Interrupt name, must be "ams-irq" > + - clocks: Should contain a clock specifier for the device > + - ranges: keep the property empty to map child address space > + (for PS and/or PL) nodes 1:1 onto the parent address > + space > + > + AMS sub-nodes: > + - ams_ps : Used as PS-SYSMON node > + - ams_pl : Used as PL-SYSMON node > + > + > + > +AMS PS-SYSMON > +````````````` > +PS (Processing System) SYSMON is memory mapped to PS. This block has built-in > +alarm generation logic that is used to interrupt the processor based on > +condition set. > + > +Required properties: > + - compatible: Should be "xlnx,zynqmp-ams-ps" > + - reg: Register space for PS-SYSMON > + > + > + > +AMS PL-SYSMON > +````````````` > +PL-SYSMON is capable of monitoring off chip voltage and temperature. PL-SYSMON > +block has DRP, JTAG and I2C interface to enable monitoring from external master. > +Out of this interface currently only DRP is supported. This block has alarm > +generation logic that is used to interrupt the processor based on condition set. > + > +Required properties: > + - compatible: Should be "xlnx,zynqmp-ams-pl" > + - reg: Register space for PL-SYSMON > + > +PL-SYSMON optional sub-nodes: > + - xlnx,ext-channels: List of external channels that are connected to the > + AMS PL module. > + > + The child nodes of PL-SYSMON represent the external channels which are > + connected to this Module. If the property is not present > + no external channels will be assumed to be connected. > + > + Each child node represents one channel and has the following > + properties: > + > + Required properties: > + * reg: Pair of pins the channel is connected to. > + > + 'reg' value Channel Name Channel Number > + ----------- ------------ -------------- > + 0 VP/VN 30 > + 1 VUSER0 31 > + 2 VUSER1 32 > + 3 VUSER3 33 > + 4 VUSER4 34 > + 5 VAUXP[0]/VAUXN[0] 35 > + 6 VAUXP[1]/VAUXN[1] 36 > + ... > + 20 VAUXP[15]/VAUXN[15] 50 > + > + Each channel number should only be used at most once. For > + more details on channels, refer table given at the end. refer to > + > + Optional properties: > + * xlnx,bipolar: If set the channel is used in bipolar > + mode. > + > + > +Example: > + xilinx_ams: ams@ffa50000 { > + compatible = "xlnx,zynqmp-ams"; > + interrupt-parent = <&gic>; > + interrupts = <0 56 4>; > + interrupt-names = "ams-irq"; > + clocks = <&clkc 70>; > + reg = <0x0 0xffa50000 0x0 0x800>; > + reg-names = "ams-base"; > + ranges; > + > + ams_ps: ams_ps@ffa50800 { > + compatible = "xlnx,zynqmp-ams-ps"; > + reg = <0x0 0xffa50800 0x0 0x400>; > + }; > + > + ams_pl: ams_pl@ffa50c00 { > + compatible = "xlnx,zynqmp-ams-pl"; > + reg = <0x0 0xffa50c00 0x0 0x400>; > + xlnx,ext-channels { > + channel@0 { > + reg = <0>; > + xlnx,bipolar; > + }; > + channel@1 { > + reg = <1>; > + }; > + channel@8 { > + reg = <8>; > + xlnx,bipolar; > + }; > + }; > + }; > + }; > + > + > +AMS Channels Details Channel Details > +```````````````````` > +Sysmon Block |Channel| Details |Measurement > + Number Type > +--------------------------------------------------------------------------------------------------------- > +AMS CTRL |0 |System PLLs voltage measurement, VCC_PSPLL. |Voltage > + |1 |Battery voltage measurement, VCC_PSBATT. |Voltage > + |2 |PL Internal voltage measurement, VCCINT. |Voltage > + |3 |Block RAM voltage measurement, VCCBRAM. |Voltage > + |4 |PL Aux voltage measurement, VCCAUX. |Voltage > + |5 |Voltage measurement for six DDR I/O PLLs, VCC_PSDDR_PLL. |Voltage > + |6 |VCC_PSINTFP_DDR voltage measurement. |Voltage > +--------------------------------------------------------------------------------------------------------- > +PS Sysmon |7 |LPD temperature measurement. |Temperature > + |8 |FPD Temperature Measurment (REMOTE). |Temperature temperature measur_e_ment (and probably lowercase?) > + |9 |VCC PS LPD voltage measurement (supply1). |Voltage > + |10 |VCC PS FPD voltage measurement (supply2). |Voltage > + |11 |PS Aux voltage reference (supply3). |Voltage > + |12 |DDR I/O VCC voltage measurement. |Voltage > + |13 |PS IO Bank 503 voltage measurement (supply5). |Voltage > + |14 |PS IO Bank 500 voltage measurement (supply6). |Voltage > + |15 |VCCO_PSIO1 voltage measurement. |Voltage > + |16 |VCCO_PSIO2 voltage measurement. |Voltage > + |17 |VCC_PS_GTR voltage measurement (VPS_MGTRAVCC). |Voltage > + |18 |VTT_PS_GTR voltage measurement (VPS_MGTRAVTT). |Voltage > + |19 |VCC_PSADC voltage measurement. |Voltage > +--------------------------------------------------------------------------------------------------------- > +PL Sysmon |20 |PL Temperature measurement. |Temperature > + |21 |PL Internal Voltage Voltage measurement, VCCINT. |Voltage Voltage Voltage? > + |22 |PL Auxiliary Voltage measurement, VCCAUX. |Voltage > + |23 |ADC Reference P+ Voltage measurement. |Voltage > + |24 |ADC Reference N- Voltage measurement. |Voltage > + |25 |PL Block RAM Voltage measurement, VCCBRAM. |Voltage > + |26 |LPD Internal Voltage measurement, VCC_PSINTLP (supply4). |Voltage > + |27 |FPD Internal Voltage measurement, VCC_PSINTFP (supply5). |Voltage > + |28 |PS Auxiliary Voltage measurement (supply6). |Voltage > + |29 |PL VCCADC Voltage measurement (vccams). |Voltage > + |30 |Differencial analog input signal Voltage measurment. |Voltage Differen_t_ial > + |31 |VUser0 Voltage measurement (supply7). |Voltage > + |32 |VUser1 Voltage measurement (supply8). |Voltage > + |33 |VUser2 Voltage measurement (supply9). |Voltage > + |34 |VUser3 Voltage measurement (supply10). |Voltage > + |35 |Auxiliary ch 0 Voltage measurement (VAux0). |Voltage > + |36 |Auxiliary ch 1 Voltage measurement (VAux1). |Voltage > + |37 |Auxiliary ch 2 Voltage measurement (VAux2). |Voltage > + |38 |Auxiliary ch 3 Voltage measurement (VAux3). |Voltage > + |39 |Auxiliary ch 4 Voltage measurement (VAux4). |Voltage > + |40 |Auxiliary ch 5 Voltage measurement (VAux5). |Voltage > + |41 |Auxiliary ch 6 Voltage measurement (VAux6). |Voltage > + |42 |Auxiliary ch 7 Voltage measurement (VAux7). |Voltage > + |43 |Auxiliary ch 8 Voltage measurement (VAux8). |Voltage > + |44 |Auxiliary ch 9 Voltage measurement (VAux9). |Voltage > + |45 |Auxiliary ch 10 Voltage measurement (VAux10). |Voltage > + |46 |Auxiliary ch 11 Voltage measurement (VAux11). |Voltage > + |47 |Auxiliary ch 12 Voltage measurement (VAux12). |Voltage > + |48 |Auxiliary ch 13 Voltage measurement (VAux13). |Voltage > + |49 |Auxiliary ch 14 Voltage measurement (VAux14). |Voltage > + |50 |Auxiliary ch 15 Voltage measurement (VAux15). |Voltage > +--------------------------------------------------------------------------------------------------------- >
diff --git a/Documentation/devicetree/bindings/iio/adc/xilinx-ams.txt b/Documentation/devicetree/bindings/iio/adc/xilinx-ams.txt new file mode 100644 index 0000000..d0958a1 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/xilinx-ams.txt @@ -0,0 +1,180 @@ +Xilinx AMS controller +````````````````````` +The AMS includes an ADC as well as on-chip sensors that can be used to +sample external voltages and monitor on-die operating conditions, such as +temperature and supply voltage levels. +The AMS has two SYSMON blocks which are PL (Programmable Logic) SYSMON and +PS (Processing System) SYSMON. +All designs should have AMS registers, but PS and PL are optional. The +AMS controller can work with only PS, only PL and both PS and PL +configurations. Please specify registers according to your design. Devicetree +should always have AMS module property. Providing PS & PL module is optional. + +Required properties: + - compatible: Should be "xlnx,zynqmp-ams" + - reg: Should specify AMS register space + - interrupts: Interrupt number for the AMS control interface + - interrupt-names: Interrupt name, must be "ams-irq" + - clocks: Should contain a clock specifier for the device + - ranges: keep the property empty to map child address space + (for PS and/or PL) nodes 1:1 onto the parent address + space + + AMS sub-nodes: + - ams_ps : Used as PS-SYSMON node + - ams_pl : Used as PL-SYSMON node + + + +AMS PS-SYSMON +````````````` +PS (Processing System) SYSMON is memory mapped to PS. This block has built-in +alarm generation logic that is used to interrupt the processor based on +condition set. + +Required properties: + - compatible: Should be "xlnx,zynqmp-ams-ps" + - reg: Register space for PS-SYSMON + + + +AMS PL-SYSMON +````````````` +PL-SYSMON is capable of monitoring off chip voltage and temperature. PL-SYSMON +block has DRP, JTAG and I2C interface to enable monitoring from external master. +Out of this interface currently only DRP is supported. This block has alarm +generation logic that is used to interrupt the processor based on condition set. + +Required properties: + - compatible: Should be "xlnx,zynqmp-ams-pl" + - reg: Register space for PL-SYSMON + +PL-SYSMON optional sub-nodes: + - xlnx,ext-channels: List of external channels that are connected to the + AMS PL module. + + The child nodes of PL-SYSMON represent the external channels which are + connected to this Module. If the property is not present + no external channels will be assumed to be connected. + + Each child node represents one channel and has the following + properties: + + Required properties: + * reg: Pair of pins the channel is connected to. + + 'reg' value Channel Name Channel Number + ----------- ------------ -------------- + 0 VP/VN 30 + 1 VUSER0 31 + 2 VUSER1 32 + 3 VUSER3 33 + 4 VUSER4 34 + 5 VAUXP[0]/VAUXN[0] 35 + 6 VAUXP[1]/VAUXN[1] 36 + ... + 20 VAUXP[15]/VAUXN[15] 50 + + Each channel number should only be used at most once. For + more details on channels, refer table given at the end. + + Optional properties: + * xlnx,bipolar: If set the channel is used in bipolar + mode. + + +Example: + xilinx_ams: ams@ffa50000 { + compatible = "xlnx,zynqmp-ams"; + interrupt-parent = <&gic>; + interrupts = <0 56 4>; + interrupt-names = "ams-irq"; + clocks = <&clkc 70>; + reg = <0x0 0xffa50000 0x0 0x800>; + reg-names = "ams-base"; + ranges; + + ams_ps: ams_ps@ffa50800 { + compatible = "xlnx,zynqmp-ams-ps"; + reg = <0x0 0xffa50800 0x0 0x400>; + }; + + ams_pl: ams_pl@ffa50c00 { + compatible = "xlnx,zynqmp-ams-pl"; + reg = <0x0 0xffa50c00 0x0 0x400>; + xlnx,ext-channels { + channel@0 { + reg = <0>; + xlnx,bipolar; + }; + channel@1 { + reg = <1>; + }; + channel@8 { + reg = <8>; + xlnx,bipolar; + }; + }; + }; + }; + + +AMS Channels Details +```````````````````` +Sysmon Block |Channel| Details |Measurement + Number Type +--------------------------------------------------------------------------------------------------------- +AMS CTRL |0 |System PLLs voltage measurement, VCC_PSPLL. |Voltage + |1 |Battery voltage measurement, VCC_PSBATT. |Voltage + |2 |PL Internal voltage measurement, VCCINT. |Voltage + |3 |Block RAM voltage measurement, VCCBRAM. |Voltage + |4 |PL Aux voltage measurement, VCCAUX. |Voltage + |5 |Voltage measurement for six DDR I/O PLLs, VCC_PSDDR_PLL. |Voltage + |6 |VCC_PSINTFP_DDR voltage measurement. |Voltage +--------------------------------------------------------------------------------------------------------- +PS Sysmon |7 |LPD temperature measurement. |Temperature + |8 |FPD Temperature Measurment (REMOTE). |Temperature + |9 |VCC PS LPD voltage measurement (supply1). |Voltage + |10 |VCC PS FPD voltage measurement (supply2). |Voltage + |11 |PS Aux voltage reference (supply3). |Voltage + |12 |DDR I/O VCC voltage measurement. |Voltage + |13 |PS IO Bank 503 voltage measurement (supply5). |Voltage + |14 |PS IO Bank 500 voltage measurement (supply6). |Voltage + |15 |VCCO_PSIO1 voltage measurement. |Voltage + |16 |VCCO_PSIO2 voltage measurement. |Voltage + |17 |VCC_PS_GTR voltage measurement (VPS_MGTRAVCC). |Voltage + |18 |VTT_PS_GTR voltage measurement (VPS_MGTRAVTT). |Voltage + |19 |VCC_PSADC voltage measurement. |Voltage +--------------------------------------------------------------------------------------------------------- +PL Sysmon |20 |PL Temperature measurement. |Temperature + |21 |PL Internal Voltage Voltage measurement, VCCINT. |Voltage + |22 |PL Auxiliary Voltage measurement, VCCAUX. |Voltage + |23 |ADC Reference P+ Voltage measurement. |Voltage + |24 |ADC Reference N- Voltage measurement. |Voltage + |25 |PL Block RAM Voltage measurement, VCCBRAM. |Voltage + |26 |LPD Internal Voltage measurement, VCC_PSINTLP (supply4). |Voltage + |27 |FPD Internal Voltage measurement, VCC_PSINTFP (supply5). |Voltage + |28 |PS Auxiliary Voltage measurement (supply6). |Voltage + |29 |PL VCCADC Voltage measurement (vccams). |Voltage + |30 |Differencial analog input signal Voltage measurment. |Voltage + |31 |VUser0 Voltage measurement (supply7). |Voltage + |32 |VUser1 Voltage measurement (supply8). |Voltage + |33 |VUser2 Voltage measurement (supply9). |Voltage + |34 |VUser3 Voltage measurement (supply10). |Voltage + |35 |Auxiliary ch 0 Voltage measurement (VAux0). |Voltage + |36 |Auxiliary ch 1 Voltage measurement (VAux1). |Voltage + |37 |Auxiliary ch 2 Voltage measurement (VAux2). |Voltage + |38 |Auxiliary ch 3 Voltage measurement (VAux3). |Voltage + |39 |Auxiliary ch 4 Voltage measurement (VAux4). |Voltage + |40 |Auxiliary ch 5 Voltage measurement (VAux5). |Voltage + |41 |Auxiliary ch 6 Voltage measurement (VAux6). |Voltage + |42 |Auxiliary ch 7 Voltage measurement (VAux7). |Voltage + |43 |Auxiliary ch 8 Voltage measurement (VAux8). |Voltage + |44 |Auxiliary ch 9 Voltage measurement (VAux9). |Voltage + |45 |Auxiliary ch 10 Voltage measurement (VAux10). |Voltage + |46 |Auxiliary ch 11 Voltage measurement (VAux11). |Voltage + |47 |Auxiliary ch 12 Voltage measurement (VAux12). |Voltage + |48 |Auxiliary ch 13 Voltage measurement (VAux13). |Voltage + |49 |Auxiliary ch 14 Voltage measurement (VAux14). |Voltage + |50 |Auxiliary ch 15 Voltage measurement (VAux15). |Voltage +---------------------------------------------------------------------------------------------------------
Xilinx AMS have several ADC channels that can be used for measurement of different voltages and temperatures. Document the same in the bindings. Signed-off-by: Manish Narani <manish.narani@xilinx.com> --- .../devicetree/bindings/iio/adc/xilinx-ams.txt | 180 +++++++++++++++++++++ 1 file changed, 180 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/xilinx-ams.txt