diff mbox series

[08/29] dt-bindings:iio:pressure:hoperf,hp03 yaml conversion

Message ID 20201011170749.243680-9-jic23@kernel.org (mailing list archive)
State New
Headers show
Series dt-bindings:iio: Another set of yaml conversions. | expand

Commit Message

Jonathan Cameron Oct. 11, 2020, 5:07 p.m. UTC
From: Jonathan Cameron <Jonathan.Cameron@huawei.com>

One quirk in the txt file was that the xclr gpio was specified as
gpio-xclr rather than gpios-xclr. I've fixed that in the
yaml version.

Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Marek Vasut <marex@denx.de>
---
 .../bindings/iio/pressure/hoperf,hp03.yaml    | 47 +++++++++++++++++++
 .../devicetree/bindings/iio/pressure/hp03.txt | 17 -------
 2 files changed, 47 insertions(+), 17 deletions(-)

Comments

Rob Herring Oct. 12, 2020, 1:06 p.m. UTC | #1
On Sun, Oct 11, 2020 at 12:10 PM Jonathan Cameron <jic23@kernel.org> wrote:
>
> From: Jonathan Cameron <Jonathan.Cameron@huawei.com>
>
> One quirk in the txt file was that the xclr gpio was specified as
> gpio-xclr rather than gpios-xclr. I've fixed that in the

xclr-gpios?, not gpios?-xclr

> yaml version.
>
> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> Cc: Marek Vasut <marex@denx.de>
> ---
>  .../bindings/iio/pressure/hoperf,hp03.yaml    | 47 +++++++++++++++++++
>  .../devicetree/bindings/iio/pressure/hp03.txt | 17 -------
>  2 files changed, 47 insertions(+), 17 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/iio/pressure/hoperf,hp03.yaml b/Documentation/devicetree/bindings/iio/pressure/hoperf,hp03.yaml
> new file mode 100644
> index 000000000000..69a3759e23db
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/pressure/hoperf,hp03.yaml
> @@ -0,0 +1,47 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/pressure/hoperf,hp03.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: HopeRF HP03 digital pressure/temperature sensors
> +
> +maintainers:
> +  - Marek Vasut <marex@denx.de>
> +
> +description: |
> +  Digital pressure and temperature sensor with an I2C interface.
> +
> +properties:
> +  compatible:
> +    const: hoperf,hp03
> +
> +  reg:
> +    maxItems: 1
> +
> +  xclr-gpios:
> +    description:
> +      The XCLR pin is a reset of the ADC in the chip, it must be pulled
> +      HI before the conversion and readout of the value from the ADC
> +      registers and pulled LO afterward.
> +    maxItems: 1
> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        pressure@77 {
> +            compatible = "hoperf,hp03";
> +            reg = <0x77>;
> +            xclr-gpios = <&portc 0 0x0>;
> +        };
> +    };
> +...
> diff --git a/Documentation/devicetree/bindings/iio/pressure/hp03.txt b/Documentation/devicetree/bindings/iio/pressure/hp03.txt
> deleted file mode 100644
> index 831dbee7a5c3..000000000000
> --- a/Documentation/devicetree/bindings/iio/pressure/hp03.txt
> +++ /dev/null
> @@ -1,17 +0,0 @@
> -HopeRF HP03 digital pressure/temperature sensors
> -
> -Required properties:
> -- compatible: must be "hoperf,hp03"
> -- xclr-gpio: must be device tree identifier of the XCLR pin.
> -             The XCLR pin is a reset of the ADC in the chip,
> -             it must be pulled HI before the conversion and
> -             readout of the value from the ADC registers and
> -             pulled LO afterward.
> -
> -Example:
> -
> -hp03@77 {
> -       compatible = "hoperf,hp03";
> -       reg = <0x77>;
> -       xclr-gpio = <&portc 0 0x0>;
> -};
> --
> 2.28.0
>
Jonathan Cameron Oct. 12, 2020, 2:31 p.m. UTC | #2
On Mon, 12 Oct 2020 08:06:46 -0500
Rob Herring <robh+dt@kernel.org> wrote:

> On Sun, Oct 11, 2020 at 12:10 PM Jonathan Cameron <jic23@kernel.org> wrote:
> >
> > From: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> >
> > One quirk in the txt file was that the xclr gpio was specified as
> > gpio-xclr rather than gpios-xclr. I've fixed that in the  
> 
> xclr-gpios?, not gpios?-xclr

I clearly have a very short memory when writing patch descriptions.
Indeed, xclr-gpios is what this should say. 


> 
> > yaml version.
> >
> > Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> > Cc: Marek Vasut <marex@denx.de>
> > ---
> >  .../bindings/iio/pressure/hoperf,hp03.yaml    | 47 +++++++++++++++++++
> >  .../devicetree/bindings/iio/pressure/hp03.txt | 17 -------
> >  2 files changed, 47 insertions(+), 17 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/iio/pressure/hoperf,hp03.yaml b/Documentation/devicetree/bindings/iio/pressure/hoperf,hp03.yaml
> > new file mode 100644
> > index 000000000000..69a3759e23db
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/iio/pressure/hoperf,hp03.yaml
> > @@ -0,0 +1,47 @@
> > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/iio/pressure/hoperf,hp03.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: HopeRF HP03 digital pressure/temperature sensors
> > +
> > +maintainers:
> > +  - Marek Vasut <marex@denx.de>
> > +
> > +description: |
> > +  Digital pressure and temperature sensor with an I2C interface.
> > +
> > +properties:
> > +  compatible:
> > +    const: hoperf,hp03
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  xclr-gpios:
> > +    description:
> > +      The XCLR pin is a reset of the ADC in the chip, it must be pulled
> > +      HI before the conversion and readout of the value from the ADC
> > +      registers and pulled LO afterward.
> > +    maxItems: 1
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > +  - |
> > +    i2c {
> > +        #address-cells = <1>;
> > +        #size-cells = <0>;
> > +
> > +        pressure@77 {
> > +            compatible = "hoperf,hp03";
> > +            reg = <0x77>;
> > +            xclr-gpios = <&portc 0 0x0>;
> > +        };
> > +    };
> > +...
> > diff --git a/Documentation/devicetree/bindings/iio/pressure/hp03.txt b/Documentation/devicetree/bindings/iio/pressure/hp03.txt
> > deleted file mode 100644
> > index 831dbee7a5c3..000000000000
> > --- a/Documentation/devicetree/bindings/iio/pressure/hp03.txt
> > +++ /dev/null
> > @@ -1,17 +0,0 @@
> > -HopeRF HP03 digital pressure/temperature sensors
> > -
> > -Required properties:
> > -- compatible: must be "hoperf,hp03"
> > -- xclr-gpio: must be device tree identifier of the XCLR pin.
> > -             The XCLR pin is a reset of the ADC in the chip,
> > -             it must be pulled HI before the conversion and
> > -             readout of the value from the ADC registers and
> > -             pulled LO afterward.
> > -
> > -Example:
> > -
> > -hp03@77 {
> > -       compatible = "hoperf,hp03";
> > -       reg = <0x77>;
> > -       xclr-gpio = <&portc 0 0x0>;
> > -};
> > --
> > 2.28.0
> >
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/iio/pressure/hoperf,hp03.yaml b/Documentation/devicetree/bindings/iio/pressure/hoperf,hp03.yaml
new file mode 100644
index 000000000000..69a3759e23db
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/pressure/hoperf,hp03.yaml
@@ -0,0 +1,47 @@ 
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/pressure/hoperf,hp03.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HopeRF HP03 digital pressure/temperature sensors
+
+maintainers:
+  - Marek Vasut <marex@denx.de>
+
+description: |
+  Digital pressure and temperature sensor with an I2C interface.
+
+properties:
+  compatible:
+    const: hoperf,hp03
+
+  reg:
+    maxItems: 1
+
+  xclr-gpios:
+    description:
+      The XCLR pin is a reset of the ADC in the chip, it must be pulled
+      HI before the conversion and readout of the value from the ADC
+      registers and pulled LO afterward.
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pressure@77 {
+            compatible = "hoperf,hp03";
+            reg = <0x77>;
+            xclr-gpios = <&portc 0 0x0>;
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/iio/pressure/hp03.txt b/Documentation/devicetree/bindings/iio/pressure/hp03.txt
deleted file mode 100644
index 831dbee7a5c3..000000000000
--- a/Documentation/devicetree/bindings/iio/pressure/hp03.txt
+++ /dev/null
@@ -1,17 +0,0 @@ 
-HopeRF HP03 digital pressure/temperature sensors
-
-Required properties:
-- compatible: must be "hoperf,hp03"
-- xclr-gpio: must be device tree identifier of the XCLR pin.
-             The XCLR pin is a reset of the ADC in the chip,
-             it must be pulled HI before the conversion and
-             readout of the value from the ADC registers and
-             pulled LO afterward.
-
-Example:
-
-hp03@77 {
-	compatible = "hoperf,hp03";
-	reg = <0x77>;
-	xclr-gpio = <&portc 0 0x0>;
-};