new file mode 100644
@@ -0,0 +1,161 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/proximity/semtech,sx9324.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Semtech's SX9324 capacitive proximity sensor
+
+maintainers:
+ - Gwendal Grignou <gwendal@chromium.org>
+ - Daniel Campello <campello@chromium.org>
+
+description: |
+ Semtech's SX9324 proximity sensor.
+
+properties:
+ compatible:
+ const: semtech,sx9324
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ description:
+ Generated by device to announce preceding read request has finished
+ and data is available or that a close/far proximity event has happened.
+ maxItems: 1
+
+ vdd-supply:
+ description: Main power supply
+
+ svdd-supply:
+ description: Host interface power supply
+
+ "#io-channel-cells":
+ const: 1
+
+ semtech,ph0-pin:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: |
+ Array of 3 entries. Index represent the id of the CS pin.
+ Value indicates how each CS pin is used during phase 0.
+ Each of the 3 pins have the following value -
+ 0 : unused (high impedance)
+ 1 : measured input
+ 2 : dynamic shield
+ 3 : grounded.
+ For instance, CS0 measured, CS1 shield and CS2 ground is [1, 2, 3]
+ items:
+ enum: [ 0, 1, 2, 3 ]
+ minItems: 3
+ maxItems: 3
+
+ semtech,ph1-pin:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: Same as ph0-pin for phase 1.
+ items:
+ enum: [ 0, 1, 2, 3 ]
+ minItems: 3
+ maxItems: 3
+
+ semtech,ph2-pin:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: Same as ph0-pin for phase 2.
+ items:
+ enum: [ 0, 1, 2, 3 ]
+ minItems: 3
+ maxItems: 3
+
+ semtech,ph3-pin:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: Same as ph0-pin for phase 3.
+ items:
+ enum: [ 0, 1, 2, 3 ]
+ minItems: 3
+ maxItems: 3
+
+
+ semtech,ph01-resolution:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [8, 16, 32, 64, 128, 256, 512, 1024]
+ description:
+ Capacitance measurement resolution. For phase 0 and 1.
+ Higher the number, higher the resolution.
+ default: 128
+
+ semtech,ph23-resolution:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [8, 16, 32, 64, 128, 256, 512, 1024]
+ description:
+ Capacitance measurement resolution. For phase 2 and 3
+ default: 128
+
+ semtech,startup-sensor:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 0
+ description: |
+ Phase used for start-up proximity detection.
+ It is used when we enable a phase to remove static offset and measure
+ only capacitance changes introduced by the user.
+
+ semtech,ph01-proxraw-strength:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 7
+ default: 1
+ description:
+ PROXRAW filter strength for phase 0 and 1. A value of 0 represents off,
+ and other values represent 1-1/2^N.
+
+ semtech,ph23-proxraw-strength:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 7
+ default: 1
+ description:
+ Same as proxraw-strength01, for phase 2 and 3.
+
+ semtech,avg-pos-strength:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 16, 64, 128, 256, 512, 1024, 4294967295]
+ default: 16
+ description: |
+ Average positive filter strength. A value of 0 represents off and
+ UINT_MAX (4294967295) represents infinite. Other values
+ represent 1-1/N.
+
+required:
+ - compatible
+ - reg
+ - "#io-channel-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ proximity@28 {
+ compatible = "semtech,sx9324";
+ reg = <0x28>;
+ interrupt-parent = <&pio>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW 5>;
+ vdd-supply = <&pp3300_a>;
+ svdd-supply = <&pp1800_prox>;
+ #io-channel-cells = <1>;
+ semtech,ph0-pin = <1 2 3>;
+ semtech,ph1-pin = <3 2 1>;
+ semtech,ph2-pin = <1 2 3>;
+ semtech,ph3-pin = <3 2 1>;
+ semtech,ph01-resolution = <256>;
+ semtech,ph23-resolution = <256>;
+ semtech,startup-sensor = <1>;
+ semtech,ph01-proxraw-strength = <2>;
+ semtech,ph23-proxraw-strength = <2>;
+ semtech,avg-pos-strength = <64>;
+ };
+ };
Similar to SX9310, add biddings to setup sx9324 hardware properties. SX9324 is a little different, introduce 4 phases to be configured in 2 pairs over 3 antennas. Signed-off-by: Gwendal Grignou <gwendal@chromium.org> --- Changes in v7: - Fix 2 remaining syntax error in example. Changes in v6: - Fix syntax errors in device tree binding documentation. - Run 'make dt_binding_check' to make fix errors. Changes in v5: - Use consistent field naming, prefixed with phX. Changes in v4: - Use const instead of single enum - Specify ph0-pin better - Recopy type information for phX-pin - Fix cut and paste errors. Changes in v3: - Remove duplicate information. - Use intervals instead of enum. - Fix filter description. Changes in v2: - Fix interrupt documentation wording. .../iio/proximity/semtech,sx9324.yaml | 161 ++++++++++++++++++ 1 file changed, 161 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml