| Message ID | 20230929200844.23316-2-fr0st61te@gmail.com (mailing list archive) |
|---|---|
| State | Changes Requested |
| Headers | show |
| Series | Add maxim max34408/34409 ADC driver and yaml | expand |
On Fri, 29 Sep 2023 23:08:43 +0300, Ivan Mikhaylov wrote: > The hardware binding for i2c current monitoring device with overcurrent > control. > > Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com> > --- > .../bindings/iio/adc/maxim,max34408.yaml | 101 ++++++++++++++++++ > 1 file changed, 101 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml: supply-vdd: missing type definition doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230929200844.23316-2-fr0st61te@gmail.com The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema.
Hey, On Fri, Sep 29, 2023 at 11:08:43PM +0300, Ivan Mikhaylov wrote: > The hardware binding for i2c current monitoring device with overcurrent > control. > > Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com> > --- > .../bindings/iio/adc/maxim,max34408.yaml | 101 ++++++++++++++++++ > 1 file changed, 101 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > > diff --git a/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml b/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > new file mode 100644 > index 000000000000..cdf89fa4c80e > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > @@ -0,0 +1,101 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/iio/adc/maxim,max34408.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Two- and four-channel current monitors with overcurrent control > + > +maintainers: > + - Ivan Mikhaylov <fr0st61te@gmail.com> > + > +description: | > + The MAX34408/MAX34409 are two- and four-channel current monitors that are > + configured and monitored with a standard I2C/SMBus serial interface. Each > + unidirectional current sensor offers precision high-side operation with a > + low full-scale sense voltage. The devices automatically sequence through > + two or four channels and collect the current-sense samples and average them > + to reduce the effect of impulse noise. The raw ADC samples are compared to > + user-programmable digital thresholds to indicate overcurrent conditions. > + Overcurrent conditions trigger a hardware output to provide an immediate > + indication to shut down any necessary external circuitry. > + > + Specifications about the devices can be found at: > + https://www.analog.com/media/en/technical-documentation/data-sheets/MAX34408-MAX34409.pdf > + > +properties: > + compatible: > + enum: > + - maxim,max34408 > + - maxim,max34409 > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + maxim,input1-rsense-val-micro-ohms: > + description: > + Adjust the Rsense value to monitor higher or lower current levels for > + input 1. > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] > + default: 1000 > + > + maxim,input2-rsense-val-micro-ohms: > + description: > + Adjust the Rsense value to monitor higher or lower current levels for > + input 2. > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] > + default: 1000 > + > + maxim,input3-rsense-val-micro-ohms: > + description: > + Adjust the Rsense value to monitor higher or lower current levels for > + input 3. > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] > + default: 1000 > + > + maxim,input4-rsense-val-micro-ohms: > + description: > + Adjust the Rsense value to monitor higher or lower current levels for > + input 4. > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] > + default: 1000 Having 4 almost identical properties makes it seem like this should have some channel nodes, each containing an rsense-micro-ohms type property. > + > + maxim,shtdn: > + description: > + Shutdown Output. Open-drain output. This output transitions to high impedance > + when any of the digital comparator thresholds are exceeded as long as the ENA > + pin is high. > + type: boolean I don't understand what this property is used for. The description here, and below for "ena", read like they are the descriptions in the datasheet for the pin, rather than how to use the property. The drivers don't appear to contain users either - what is the point of these properties? > + > + maxim,ena: > + description: > + SHTDN Enable Input. CMOS digital input. Connect to GND to clear the latch and > + unconditionally deassert (force low) the SHTDN output and reset the shutdown > + delay. Connect to VDD to enable normal latch operation of the SHTDN output. > + type: boolean > + > + supply-vdd: true As pointed out by the bot, this is not correct. You need to use a -supply affix, not a supply-prefix. Thanks, Conor. > + > +required: > + - compatible > + - reg > + > +additionalProperties: false > + > +examples: > + - | > + i2c { > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + adc@1e { > + compatible = "maxim,max34409"; > + reg = <0x1e>; > + maxim,input1-rsense-val-micro-ohms = <5000>; > + maxim,input2-rsense-val-micro-ohms = <10000>; > + }; > + }; > -- > 2.42.0 >
On Sat, 30 Sep 2023 10:37:09 +0100 Conor Dooley <conor@kernel.org> wrote: > Hey, > > On Fri, Sep 29, 2023 at 11:08:43PM +0300, Ivan Mikhaylov wrote: > > The hardware binding for i2c current monitoring device with overcurrent > > control. > > > > Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com> > > --- > > .../bindings/iio/adc/maxim,max34408.yaml | 101 ++++++++++++++++++ > > 1 file changed, 101 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > > > > diff --git a/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml b/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > > new file mode 100644 > > index 000000000000..cdf89fa4c80e > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > > @@ -0,0 +1,101 @@ > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/iio/adc/maxim,max34408.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Two- and four-channel current monitors with overcurrent control > > + > > +maintainers: > > + - Ivan Mikhaylov <fr0st61te@gmail.com> > > + > > +description: | > > + The MAX34408/MAX34409 are two- and four-channel current monitors that are > > + configured and monitored with a standard I2C/SMBus serial interface. Each > > + unidirectional current sensor offers precision high-side operation with a > > + low full-scale sense voltage. The devices automatically sequence through > > + two or four channels and collect the current-sense samples and average them > > + to reduce the effect of impulse noise. The raw ADC samples are compared to > > + user-programmable digital thresholds to indicate overcurrent conditions. > > + Overcurrent conditions trigger a hardware output to provide an immediate > > + indication to shut down any necessary external circuitry. > > + > > + Specifications about the devices can be found at: > > + https://www.analog.com/media/en/technical-documentation/data-sheets/MAX34408-MAX34409.pdf > > + > > +properties: > > + compatible: > > + enum: > > + - maxim,max34408 > > + - maxim,max34409 > > + > > + reg: > > + maxItems: 1 > > + > > + interrupts: > > + maxItems: 1 > > + > > + maxim,input1-rsense-val-micro-ohms: > > + description: > > + Adjust the Rsense value to monitor higher or lower current levels for > > + input 1. > > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] > > + default: 1000 > > + > > + maxim,input2-rsense-val-micro-ohms: > > + description: > > + Adjust the Rsense value to monitor higher or lower current levels for > > + input 2. > > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] > > + default: 1000 > > + > > + maxim,input3-rsense-val-micro-ohms: > > + description: > > + Adjust the Rsense value to monitor higher or lower current levels for > > + input 3. > > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] > > + default: 1000 > > + > > + maxim,input4-rsense-val-micro-ohms: > > + description: > > + Adjust the Rsense value to monitor higher or lower current levels for > > + input 4. > > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] > > + default: 1000 > > Having 4 almost identical properties makes it seem like this should have > some channel nodes, each containing an rsense-micro-ohms type property. Agreed. That is most flexible route if there is any chance of ending up with more channel specific stuff in future. There should also be some magic in here to rule out the input3 and input4 for the devices with only two channels. (lots of examples in tree) Otherwise, in theory this could be an array I guess, but I'd also prefer channel nodes. > > > + > > + maxim,shtdn: > > + description: > > + Shutdown Output. Open-drain output. This output transitions to high impedance > > + when any of the digital comparator thresholds are exceeded as long as the ENA > > + pin is high. > > + type: boolean > > I don't understand what this property is used for. The description here, > and below for "ena", read like they are the descriptions in the > datasheet for the pin, rather than how to use the property. > > The drivers don't appear to contain users either - what is the point of > these properties? > > > + > > + maxim,ena: > > + description: > > + SHTDN Enable Input. CMOS digital input. Connect to GND to clear the latch and > > + unconditionally deassert (force low) the SHTDN output and reset the shutdown > > + delay. Connect to VDD to enable normal latch operation of the SHTDN output. > > + type: boolean > > + > > + supply-vdd: true > > As pointed out by the bot, this is not correct. You need to use a > -supply affix, not a supply-prefix. My error in earlier review (not enough coffee that day I guess :) Anyhow it does show that the tests weren't run which isn't a good thing to see. Jonathan > > Thanks, > Conor. > > > + > > +required: > > + - compatible > > + - reg > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + i2c { > > + > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + adc@1e { > > + compatible = "maxim,max34409"; > > + reg = <0x1e>; > > + maxim,input1-rsense-val-micro-ohms = <5000>; > > + maxim,input2-rsense-val-micro-ohms = <10000>; > > + }; > > + }; > > -- > > 2.42.0 > >
On Sat, 2023-09-30 at 10:37 +0100, Conor Dooley wrote: > Hey, > > On Fri, Sep 29, 2023 at 11:08:43PM +0300, Ivan Mikhaylov wrote: > > The hardware binding for i2c current monitoring device with > > overcurrent > > control. > > > > Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com> > > --- > > .../bindings/iio/adc/maxim,max34408.yaml | 101 > > ++++++++++++++++++ > > 1 file changed, 101 insertions(+) > > create mode 100644 > > Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > > > > diff --git > > a/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > > b/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > > new file mode 100644 > > index 000000000000..cdf89fa4c80e > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > > @@ -0,0 +1,101 @@ > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/iio/adc/maxim,max34408.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Two- and four-channel current monitors with overcurrent > > control > > + > > +maintainers: > > + - Ivan Mikhaylov <fr0st61te@gmail.com> > > + > > +description: | > > + The MAX34408/MAX34409 are two- and four-channel current monitors > > that are > > + configured and monitored with a standard I2C/SMBus serial > > interface. Each > > + unidirectional current sensor offers precision high-side > > operation with a > > + low full-scale sense voltage. The devices automatically sequence > > through > > + two or four channels and collect the current-sense samples and > > average them > > + to reduce the effect of impulse noise. The raw ADC samples are > > compared to > > + user-programmable digital thresholds to indicate overcurrent > > conditions. > > + Overcurrent conditions trigger a hardware output to provide an > > immediate > > + indication to shut down any necessary external circuitry. > > + > > + Specifications about the devices can be found at: > > + > > https://www.analog.com/media/en/technical-documentation/data-sheets/MAX34408-MAX34409.pdf > > + > > +properties: > > + compatible: > > + enum: > > + - maxim,max34408 > > + - maxim,max34409 > > + > > + reg: > > + maxItems: 1 > > + > > + interrupts: > > + maxItems: 1 > > + > > + maxim,input1-rsense-val-micro-ohms: > > + description: > > + Adjust the Rsense value to monitor higher or lower current > > levels for > > + input 1. > > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, > > 500000] > > + default: 1000 > > + > > + maxim,input2-rsense-val-micro-ohms: > > + description: > > + Adjust the Rsense value to monitor higher or lower current > > levels for > > + input 2. > > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, > > 500000] > > + default: 1000 > > + > > + maxim,input3-rsense-val-micro-ohms: > > + description: > > + Adjust the Rsense value to monitor higher or lower current > > levels for > > + input 3. > > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, > > 500000] > > + default: 1000 > > + > > + maxim,input4-rsense-val-micro-ohms: > > + description: > > + Adjust the Rsense value to monitor higher or lower current > > levels for > > + input 4. > > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, > > 500000] > > + default: 1000 > > Having 4 almost identical properties makes it seem like this should > have > some channel nodes, each containing an rsense-micro-ohms type > property. Conor, I'll look through. > > > + > > + maxim,shtdn: > > + description: > > + Shutdown Output. Open-drain output. This output transitions > > to high impedance > > + when any of the digital comparator thresholds are exceeded > > as long as the ENA > > + pin is high. > > + type: boolean > > I don't understand what this property is used for. The description > here, > and below for "ena", read like they are the descriptions in the > datasheet for the pin, rather than how to use the property. > > The drivers don't appear to contain users either - what is the point > of > these properties? ena and shtdn physical pins of hardware, in the previous version Jonathan asked about adding them into yaml even if it's not used in code. should I do it in some other way? > > > + > > + maxim,ena: > > + description: > > + SHTDN Enable Input. CMOS digital input. Connect to GND to > > clear the latch and > > + unconditionally deassert (force low) the SHTDN output and > > reset the shutdown > > + delay. Connect to VDD to enable normal latch operation of > > the SHTDN output. > > + type: boolean > > + > > + supply-vdd: true > > As pointed out by the bot, this is not correct. You need to use a > -supply affix, not a supply-prefix. Oops. Thanks.
On Sat, 30 Sep 2023 22:38:58 +0300 Ivan Mikhaylov <fr0st61te@gmail.com> wrote: > On Sat, 2023-09-30 at 10:37 +0100, Conor Dooley wrote: > > Hey, > > > > On Fri, Sep 29, 2023 at 11:08:43PM +0300, Ivan Mikhaylov wrote: > > > The hardware binding for i2c current monitoring device with > > > overcurrent > > > control. > > > > > > Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com> > > > --- > > > .../bindings/iio/adc/maxim,max34408.yaml | 101 > > > ++++++++++++++++++ > > > 1 file changed, 101 insertions(+) > > > create mode 100644 > > > Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > > > > > > diff --git > > > a/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > > > b/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > > > new file mode 100644 > > > index 000000000000..cdf89fa4c80e > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml > > > @@ -0,0 +1,101 @@ > > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > > > +%YAML 1.2 > > > +--- > > > +$id: http://devicetree.org/schemas/iio/adc/maxim,max34408.yaml# > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > + > > > +title: Two- and four-channel current monitors with overcurrent > > > control > > > + > > > +maintainers: > > > + - Ivan Mikhaylov <fr0st61te@gmail.com> > > > + > > > +description: | > > > + The MAX34408/MAX34409 are two- and four-channel current monitors > > > that are > > > + configured and monitored with a standard I2C/SMBus serial > > > interface. Each > > > + unidirectional current sensor offers precision high-side > > > operation with a > > > + low full-scale sense voltage. The devices automatically sequence > > > through > > > + two or four channels and collect the current-sense samples and > > > average them > > > + to reduce the effect of impulse noise. The raw ADC samples are > > > compared to > > > + user-programmable digital thresholds to indicate overcurrent > > > conditions. > > > + Overcurrent conditions trigger a hardware output to provide an > > > immediate > > > + indication to shut down any necessary external circuitry. > > > + > > > + Specifications about the devices can be found at: > > > + > > > https://www.analog.com/media/en/technical-documentation/data-sheets/MAX34408-MAX34409.pdf > > > + > > > +properties: > > > + compatible: > > > + enum: > > > + - maxim,max34408 > > > + - maxim,max34409 > > > + > > > + reg: > > > + maxItems: 1 > > > + > > > + interrupts: > > > + maxItems: 1 > > > + > > > + maxim,input1-rsense-val-micro-ohms: > > > + description: > > > + Adjust the Rsense value to monitor higher or lower current > > > levels for > > > + input 1. > > > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, > > > 500000] > > > + default: 1000 > > > + > > > + maxim,input2-rsense-val-micro-ohms: > > > + description: > > > + Adjust the Rsense value to monitor higher or lower current > > > levels for > > > + input 2. > > > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, > > > 500000] > > > + default: 1000 > > > + > > > + maxim,input3-rsense-val-micro-ohms: > > > + description: > > > + Adjust the Rsense value to monitor higher or lower current > > > levels for > > > + input 3. > > > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, > > > 500000] > > > + default: 1000 > > > + > > > + maxim,input4-rsense-val-micro-ohms: > > > + description: > > > + Adjust the Rsense value to monitor higher or lower current > > > levels for > > > + input 4. > > > + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, > > > 500000] > > > + default: 1000 > > > > Having 4 almost identical properties makes it seem like this should > > have > > some channel nodes, each containing an rsense-micro-ohms type > > property. > > Conor, I'll look through. > > > > > > + > > > + maxim,shtdn: > > > + description: > > > + Shutdown Output. Open-drain output. This output transitions > > > to high impedance > > > + when any of the digital comparator thresholds are exceeded > > > as long as the ENA > > > + pin is high. > > > + type: boolean > > > > I don't understand what this property is used for. The description > > here, > > and below for "ena", read like they are the descriptions in the > > datasheet for the pin, rather than how to use the property. > > > > The drivers don't appear to contain users either - what is the point > > of > > these properties? > > ena and shtdn physical pins of hardware, in the previous version > Jonathan asked about adding them into yaml even if it's not used in > code. should I do it in some other way? Yes, use the gpio bindings. enable-gpios, isshutdown-gpios perhaps - though try and find a similar example for the naming. The shutdown one is a bit unusual in that it indicates the device has shutdown for one of several possible reasons (IIRC) Jonathan > > > > > > + > > > + maxim,ena: > > > + description: > > > + SHTDN Enable Input. CMOS digital input. Connect to GND to > > > clear the latch and > > > + unconditionally deassert (force low) the SHTDN output and > > > reset the shutdown > > > + delay. Connect to VDD to enable normal latch operation of > > > the SHTDN output. > > > + type: boolean > > > + > > > + supply-vdd: true > > > > As pointed out by the bot, this is not correct. You need to use a > > -supply affix, not a supply-prefix. > > Oops. > > Thanks. > >
diff --git a/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml b/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml new file mode 100644 index 000000000000..cdf89fa4c80e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml @@ -0,0 +1,101 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/maxim,max34408.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Two- and four-channel current monitors with overcurrent control + +maintainers: + - Ivan Mikhaylov <fr0st61te@gmail.com> + +description: | + The MAX34408/MAX34409 are two- and four-channel current monitors that are + configured and monitored with a standard I2C/SMBus serial interface. Each + unidirectional current sensor offers precision high-side operation with a + low full-scale sense voltage. The devices automatically sequence through + two or four channels and collect the current-sense samples and average them + to reduce the effect of impulse noise. The raw ADC samples are compared to + user-programmable digital thresholds to indicate overcurrent conditions. + Overcurrent conditions trigger a hardware output to provide an immediate + indication to shut down any necessary external circuitry. + + Specifications about the devices can be found at: + https://www.analog.com/media/en/technical-documentation/data-sheets/MAX34408-MAX34409.pdf + +properties: + compatible: + enum: + - maxim,max34408 + - maxim,max34409 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + maxim,input1-rsense-val-micro-ohms: + description: + Adjust the Rsense value to monitor higher or lower current levels for + input 1. + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] + default: 1000 + + maxim,input2-rsense-val-micro-ohms: + description: + Adjust the Rsense value to monitor higher or lower current levels for + input 2. + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] + default: 1000 + + maxim,input3-rsense-val-micro-ohms: + description: + Adjust the Rsense value to monitor higher or lower current levels for + input 3. + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] + default: 1000 + + maxim,input4-rsense-val-micro-ohms: + description: + Adjust the Rsense value to monitor higher or lower current levels for + input 4. + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] + default: 1000 + + maxim,shtdn: + description: + Shutdown Output. Open-drain output. This output transitions to high impedance + when any of the digital comparator thresholds are exceeded as long as the ENA + pin is high. + type: boolean + + maxim,ena: + description: + SHTDN Enable Input. CMOS digital input. Connect to GND to clear the latch and + unconditionally deassert (force low) the SHTDN output and reset the shutdown + delay. Connect to VDD to enable normal latch operation of the SHTDN output. + type: boolean + + supply-vdd: true + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + + #address-cells = <1>; + #size-cells = <0>; + + adc@1e { + compatible = "maxim,max34409"; + reg = <0x1e>; + maxim,input1-rsense-val-micro-ohms = <5000>; + maxim,input2-rsense-val-micro-ohms = <10000>; + }; + };
The hardware binding for i2c current monitoring device with overcurrent control. Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com> --- .../bindings/iio/adc/maxim,max34408.yaml | 101 ++++++++++++++++++ 1 file changed, 101 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml