@@ -14,6 +14,8 @@ description: |
https://www.analog.com/media/en/technical-documentation/data-sheets/AD7605-4.pdf
https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf
https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf
+ https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606c-16.pdf
+ https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606c-18.pdf
https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf
properties:
@@ -24,11 +26,19 @@ properties:
- adi,ad7606-6
- adi,ad7606-8 # Referred to as AD7606 (without -8) in the datasheet
- adi,ad7606b
+ - adi,ad7606c-16
+ - adi,ad7606c-18
- adi,ad7616
reg:
maxItems: 1
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
spi-cpha: true
spi-cpol: true
@@ -114,6 +124,47 @@ properties:
assumed that the pins are hardwired to VDD.
type: boolean
+patternProperties:
+ "^channel@[1-8]$":
+ type: object
+ $ref: adc.yaml
+ unevaluatedProperties: false
+
+ properties:
+ reg:
+ description:
+ The channel number, as specified in the datasheet (from 1 to 8).
+ minimum: 1
+ maximum: 8
+
+ diff-channels:
+ description:
+ Each channel can be configured as a bipolar differential channel.
+ The ADC uses the same positive and negative inputs for this.
+ This property must be specified as 'reg' (or the channel number) for
+ both positive and negative inputs (i.e. diff-channels = <reg reg>).
+ Since the configuration is bipolar differential, the 'bipolar'
+ property is required.
+ items:
+ minimum: 1
+ maximum: 8
+
+ bipolar:
+ description:
+ The ADC channels can be configured as
+ * Bipolar single-ended
+ * Unipolar single-ended
+ * Bipolar differential
+ Therefore in the DT, if no channel node is specified, it is considered
+ 'unipolar single-ended'. So for the other configurations the 'bipolar'
+ property must be specified. If 'diff-channels' is specified, it is
+ considered a bipolar differential channel. Otherwise it is bipolar
+ single-ended.
+
+ required:
+ - reg
+ - bipolar
+
required:
- compatible
- reg
@@ -170,6 +221,25 @@ allOf:
adi,conversion-start-gpios:
maxItems: 1
+ - if:
+ not:
+ required:
+ - adi,sw-mode
+ then:
+ patternProperties:
+ "^channel@[1-8]$": false
+
+ - if:
+ not:
+ properties:
+ compatible:
+ enum:
+ - adi,ad7606c-16
+ - adi,ad7606c-18
+ then:
+ patternProperties:
+ "^channel@[1-8]$": false
+
unevaluatedProperties: false
examples:
@@ -202,4 +272,54 @@ examples:
standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
};
};
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@0 {
+ compatible = "adi,ad7606c-18";
+ reg = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ spi-max-frequency = <1000000>;
+ spi-cpol;
+ spi-cpha;
+
+ avcc-supply = <&adc_vref>;
+ vdrive-supply = <&vdd_supply>;
+
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-parent = <&gpio>;
+
+ adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
+ adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+ standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
+
+ adi,sw-mode;
+
+ channel@1 {
+ reg = <1>;
+ diff-channels = <1 1>;
+ bipolar;
+ };
+
+ channel@3 {
+ reg = <3>;
+ bipolar;
+ };
+
+ channel@8 {
+ reg = <8>;
+ diff-channels = <8 8>;
+ bipolar;
+ };
+
+ };
+ };
...