new file mode 100644
@@ -0,0 +1,143 @@
+.. SPDX-License-Identifier: GPL-2.0-only
+
+=============
+AD7606 driver
+=============
+
+ADC driver for Analog Devices Inc. AD7606 and similar devices. The module name
+is ``ad7606``.
+
+Supported devices
+=================
+
+The following chips are supported by this driver:
+
+* `AD7605 <https://www.analog.com/en/products/ad7605.html>`_
+* `AD7606 <https://www.analog.com/en/products/ad7606.html>`_
+* `AD7606B <https://www.analog.com/en/products/ad7606b.html>`_
+* `AD7616 <https://www.analog.com/en/products/ad7616.html>`_
+
+Supported features
+==================
+
+SPI wiring modes
+----------------
+
+ad7606x ADCs can output data on several SDO lines (1/2/4/8). The driver
+currently supports only 1 SDO line.
+
+Parallel wiring mode
+--------------------
+
+AD7606x ADC have also a parallel interface, with 16 lines (that can be reduced
+to 8 in byte mode). The parallel interface is selected by declaring the device
+as platform in the device tree (with no io-backends node defined, see below).
+
+IIO-backend mode
+----------------
+
+This mode allows to reach the best sample rates, but it requires an external
+hardware (eg HDL or APU) to handle the low level communication.
+The backend mode is enabled when through the definition of the "io-backends"
+property in the device tree.
+
+The reference configuration for the current implementation of IIO-backend mode
+is the HDL reference provided by ADI:
+https://wiki.analog.com/resources/eval/user-guides/ad7606x-fmc/hdl
+
+This implementation embeds an IIO-backend compatible IP (adi-axi-adc) and a PWM
+connected to the conversion trigger pin.
+
++---+ +----------------------------
+| | +-------+ |AD76xx
+| A | controls | | |
+| D |-------------->| PWM |-------------->| cnvst
+| 7 | | | |
+| 6 | +-------+ |
+| 0 | controls +-----------+-----------+ |
+| 6 |---------->| | |<--| frstdata
+| | | Backend | Backend |<--| busy
+| D | | Driver | | |
+| R | | | |-->| clk
+| I | requests |+---------+| DMA | |
+| V |----------->| Buffer ||<---- |<=>| DATA
+| E | |+---------+| | |
+| R | +-----------+-----------+ |
+| |-------------------------------------->| reset/configuration gpios
++---+ +-----------------------------
+
+
+Software and hardware modes
+---------------------------
+
+While all the AD7606 series parts can be configured using GPIOs, some of them
+can be configured using register.
+
+The chips that support software mode have more values available for configuring
+the device, as well as more settings, and allow to control the range and
+calibration per channel.
+
+The following settings are available per channel in software mode:
+ - Scale
+
+Also, there is a broader choice of oversampling ratios in software mode.
+
+Conversion triggering
+---------------------
+
+The conversion can be triggered by two distinct ways:
+
+ - A GPIO is connected to the conversion trigger pin, and this GPIO is controlled
+ by the driver directly. In this configuration, the driver sets back the
+ conversion trigger pin to high as soon as it has read all the conversions.
+
+ - An external source is connected to the conversion trigger pin. In the
+ current implementation, it must be a PWM. In this configuration, the driver
+ does not control directly the conversion trigger pin. Instead, it can
+ control the PWM's frequency. This trigger is enabled only for iio-backend.
+
+Reference voltage
+-----------------
+
+2 possible reference voltage sources are supported:
+
+ - Internal reference (2.5V)
+ - External reference (2.5V)
+
+The source is determined by the device tree. If ``refin-supply`` is present,
+then the external reference is used, otherwise the internal reference is used.
+
+Oversampling
+------------
+
+This family supports oversampling to improve SNR.
+In software mode, the following ratios are available:
+1 (oversampling disabled)/2/4/8/16/32/64/128/256.
+
+Unimplemented features
+----------------------
+
+- 2/4/8 SDO lines
+- CRC indication
+- Calibration
+
+Device buffers
+==============
+
+IIO triggered buffer
+--------------------
+
+This driver supports IIO triggered buffers, with a "built in" trigger, i.e the
+trigger is allocated and linked by the driver, and a new conversion is triggered
+as soon as the samples are transferred, and a timestamp channel is added to make
+up for the potential jitter induced by the delays in the interrupt handling.
+
+IIO backend buffer
+------------------
+
+When IIO backend is used, the trigger is not needed, and the sample rate is
+considered as stable, hence there is no timestamp channel. The communication is
+delegated to an external logic, called a backend, and the backend's driver
+handles the buffer. When this mode is enabled, the driver cannot control the
+conversion pin, because the busy pin is bound to the backend.
+
The Analog Devices Inc. AD7606 (and similar chips) are complex ADCs that will benefit from a detailed driver documentation. This documents the current features supported by the driver. Signed-off-by: Guillaume Stols <gstols@baylibre.com> --- Documentation/iio/ad7606.rst | 143 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 143 insertions(+)