@@ -47,6 +47,36 @@ In this mode, CNV and CS are tied together and there is a single SDO line.
To use this mode, in the device tree, omit the ``cnv-gpios`` and
``spi-rx-bus-width`` properties.
+SPI offload wiring
+^^^^^^^^^^^^^^^^^^
+
+When used with a SPI offload, the supported wiring configuration is:
+
+.. code-block::
+
+ +-------------+ +-------------+
+ | GP0/BUSY |-------->| TRIGGER |
+ | CS |<--------| CS |
+ | | | |
+ | ADC | | SPI |
+ | | | |
+ | SDI |<--------| SDO |
+ | SDO |-------->| SDI |
+ | SCLK |<--------| SCLK |
+ | | | |
+ | | +-------------+
+ | CNV |<-----+--| PWM |
+ | | +--| GPIO |
+ +-------------+ +-------------+
+
+In this case, both the ``cnv-gpios`` and ``pwms`` properties are required.
+The ``#trigger-source-cells = <2>`` property is also required to connect back
+to the SPI offload. The SPI offload will have ``trigger-sources`` property
+with cells to indicate the busy signal and which GPx pin is used, e.g
+``<&ad4695 AD4695_TRIGGER_EVENT_BUSY AD4695_TRIGGER_PIN_GP0>``.
+
+.. seealso:: `SPI offload support`_
+
Channel configuration
---------------------
@@ -158,6 +188,27 @@ Unimplemented features
- GPIO support
- CRC support
+SPI offload support
+===================
+
+To be able to achieve the maximum sample rate, the driver can be used with the
+`AXI SPI Engine`_ to provide SPI offload support.
+
+.. _AXI SPI Engine: http://analogdevicesinc.github.io/hdl/projects/ad469x_fmc/index.html
+
+.. seealso:: `SPI offload wiring`_
+
+When SPI offload is being used, some attributes will be different.
+
+* ``trigger`` directory is removed.
+* ``in_voltage0_sampling_frequency`` attributes are added for setting the sample
+ rate.
+* ``in_voltage0_sampling_frequency_available`` attributes are added for querying
+ the max sample rate.
+* ``timestamp`` channel is removed.
+* Buffer data format may be different compared to when offload is not used,
+ e.g. the ``in_voltage0_type`` attribute.
+
Device buffers
==============
@@ -165,3 +216,20 @@ This driver supports hardware triggered buffers. This uses the "advanced
sequencer" feature of the chip to trigger a burst of conversions.
Also see :doc:`iio_devbuf` for more general information.
+
+Effective sample rate for buffered reads
+----------------------------------------
+
+When SPI offload is not used, the sample rate is determined by the trigger that
+is manually configured in userspace. All enabled channels will be read in a
+burst when the trigger is received.
+
+When SPI offload is used, the sample rate is configured per channel. All
+all channels will have the same rate, so only one ``sampling_frequency``
+attribute needs to be set. Since this rate determines the delay between each
+individual conversion, the effective sample rate for each sample is actually
+the sum of the periods of each enabled channel in a buffered read. In other
+words, it is the value of the ``sampling_frequency`` attribute divided by the
+number of enabled channels. So if 4 channels are enabled, with the
+``sampling_frequency`` attributes set to 1 MHz, the effective sample rate is
+250 kHz.
Document SPI offload support for the ad4695 driver. Signed-off-by: David Lechner <dlechner@baylibre.com> --- v5 changes: new patch in v5 --- Documentation/iio/ad4695.rst | 68 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 68 insertions(+)