diff mbox series

[v5,08/10] iio: accel: adxl345: initialize FIFO delay value for SPI

Message ID 20241205171343.308963-9-l.rubusch@gmail.com (mailing list archive)
State Changes Requested
Headers show
Series iio: accel: adxl345: add FIFO operating with IRQ triggered watermark events | expand

Commit Message

Lothar Rubusch Dec. 5, 2024, 5:13 p.m. UTC
Add the possibility to delay FIFO access when SPI is used. According to
the datasheet this is needed for the adxl345. When initialization
happens over SPI the need for delay is to be signalized, and the delay
will be used.

Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
---
 drivers/iio/accel/adxl345.h      |  1 +
 drivers/iio/accel/adxl345_core.c | 12 ++++++++++++
 drivers/iio/accel/adxl345_i2c.c  |  2 +-
 drivers/iio/accel/adxl345_spi.c  |  7 +++++--
 4 files changed, 19 insertions(+), 3 deletions(-)

Comments

Jonathan Cameron Dec. 8, 2024, 4:16 p.m. UTC | #1
On Thu,  5 Dec 2024 17:13:41 +0000
Lothar Rubusch <l.rubusch@gmail.com> wrote:

> Add the possibility to delay FIFO access when SPI is used. According to
> the datasheet this is needed for the adxl345. When initialization
> happens over SPI the need for delay is to be signalized, and the delay
> will be used.
> 
> Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Hi Lothar,

1 trivial comment below.

Jonathan
> diff --git a/drivers/iio/accel/adxl345_spi.c b/drivers/iio/accel/adxl345_spi.c
> index 61fd9a6f5fc..9829d5d3d43 100644
> --- a/drivers/iio/accel/adxl345_spi.c
> +++ b/drivers/iio/accel/adxl345_spi.c
> @@ -12,6 +12,7 @@
>  #include "adxl345.h"
>  
>  #define ADXL345_MAX_SPI_FREQ_HZ		5000000
> +#define ADXL345_MAX_FREQ_NO_FIFO_DELAY	1500000
>  
>  static const struct regmap_config adxl345_spi_regmap_config = {
>  	.reg_bits = 8,
> @@ -28,6 +29,7 @@ static int adxl345_spi_setup(struct device *dev, struct regmap *regmap)
>  static int adxl345_spi_probe(struct spi_device *spi)
>  {
>  	struct regmap *regmap;
> +	bool needs_delay;
>  
>  	/* Bail out if max_speed_hz exceeds 5 MHz */
>  	if (spi->max_speed_hz > ADXL345_MAX_SPI_FREQ_HZ)
> @@ -38,10 +40,11 @@ static int adxl345_spi_probe(struct spi_device *spi)
>  	if (IS_ERR(regmap))
>  		return dev_err_probe(&spi->dev, PTR_ERR(regmap), "Error initializing regmap\n");
>  
> +	needs_delay = (spi->max_speed_hz > ADXL345_MAX_FREQ_NO_FIFO_DELAY);

Excess brackets.  I'd drop them.

>  	if (spi->mode & SPI_3WIRE)
> -		return adxl345_core_probe(&spi->dev, regmap, adxl345_spi_setup);
> +		return adxl345_core_probe(&spi->dev, regmap, needs_delay, adxl345_spi_setup);
>  	else
> -		return adxl345_core_probe(&spi->dev, regmap, NULL);
> +		return adxl345_core_probe(&spi->dev, regmap, needs_delay, NULL);
>  }
>  
>  static const struct adxl345_chip_info adxl345_spi_info = {
diff mbox series

Patch

diff --git a/drivers/iio/accel/adxl345.h b/drivers/iio/accel/adxl345.h
index ed81d5cf445..c07709350d3 100644
--- a/drivers/iio/accel/adxl345.h
+++ b/drivers/iio/accel/adxl345.h
@@ -127,6 +127,7 @@  struct adxl345_chip_info {
 };
 
 int adxl345_core_probe(struct device *dev, struct regmap *regmap,
+		       bool fifo_delay_default,
 		       int (*setup)(struct device*, struct regmap*));
 
 #endif /* _ADXL345_H_ */
diff --git a/drivers/iio/accel/adxl345_core.c b/drivers/iio/accel/adxl345_core.c
index e0a8b32239f..0696e908bdf 100644
--- a/drivers/iio/accel/adxl345_core.c
+++ b/drivers/iio/accel/adxl345_core.c
@@ -22,6 +22,7 @@  struct adxl345_state {
 	int irq;
 	const struct adxl345_chip_info *info;
 	struct regmap *regmap;
+	bool fifo_delay; /* delay: delay is needed for SPI */
 	u8 intio;
 };
 
@@ -193,12 +194,21 @@  static const struct iio_info adxl345_info = {
  * adxl345_core_probe() - Probe and setup for the accelerometer.
  * @dev:	Driver model representation of the device
  * @regmap:	Regmap instance for the device
+ * @fifo_delay_default: Using FIFO with SPI needs delay
  * @setup:	Setup routine to be executed right before the standard device
  *		setup
  *
+ * For SPI operation greater than 1.6 MHz, it is necessary to deassert the CS
+ * pin to ensure a total delay of 5 us; otherwise, the delay is not sufficient.
+ * The total delay necessary for 5 MHz operation is at most 3.4 us. This is not
+ * a concern when using I2C mode because the communication rate is low enough
+ * to ensure a sufficient delay between FIFO reads.
+ * Ref: "Retrieving Data from FIFO", p. 21 of 36, Data Sheet ADXL345 Rev. G
+ *
  * Return: 0 on success, negative errno on error
  */
 int adxl345_core_probe(struct device *dev, struct regmap *regmap,
+		       bool fifo_delay_default,
 		       int (*setup)(struct device*, struct regmap*))
 {
 	struct adxl345_state *st;
@@ -230,6 +240,8 @@  int adxl345_core_probe(struct device *dev, struct regmap *regmap,
 	if (!st->info)
 		return -ENODEV;
 
+	st->fifo_delay = fifo_delay_default;
+
 	indio_dev->name = st->info->name;
 	indio_dev->info = &adxl345_info;
 	indio_dev->modes = INDIO_DIRECT_MODE;
diff --git a/drivers/iio/accel/adxl345_i2c.c b/drivers/iio/accel/adxl345_i2c.c
index 4065b8f7c8a..28d997c5860 100644
--- a/drivers/iio/accel/adxl345_i2c.c
+++ b/drivers/iio/accel/adxl345_i2c.c
@@ -27,7 +27,7 @@  static int adxl345_i2c_probe(struct i2c_client *client)
 	if (IS_ERR(regmap))
 		return dev_err_probe(&client->dev, PTR_ERR(regmap), "Error initializing regmap\n");
 
-	return adxl345_core_probe(&client->dev, regmap, NULL);
+	return adxl345_core_probe(&client->dev, regmap, false, NULL);
 }
 
 static const struct adxl345_chip_info adxl345_i2c_info = {
diff --git a/drivers/iio/accel/adxl345_spi.c b/drivers/iio/accel/adxl345_spi.c
index 61fd9a6f5fc..9829d5d3d43 100644
--- a/drivers/iio/accel/adxl345_spi.c
+++ b/drivers/iio/accel/adxl345_spi.c
@@ -12,6 +12,7 @@ 
 #include "adxl345.h"
 
 #define ADXL345_MAX_SPI_FREQ_HZ		5000000
+#define ADXL345_MAX_FREQ_NO_FIFO_DELAY	1500000
 
 static const struct regmap_config adxl345_spi_regmap_config = {
 	.reg_bits = 8,
@@ -28,6 +29,7 @@  static int adxl345_spi_setup(struct device *dev, struct regmap *regmap)
 static int adxl345_spi_probe(struct spi_device *spi)
 {
 	struct regmap *regmap;
+	bool needs_delay;
 
 	/* Bail out if max_speed_hz exceeds 5 MHz */
 	if (spi->max_speed_hz > ADXL345_MAX_SPI_FREQ_HZ)
@@ -38,10 +40,11 @@  static int adxl345_spi_probe(struct spi_device *spi)
 	if (IS_ERR(regmap))
 		return dev_err_probe(&spi->dev, PTR_ERR(regmap), "Error initializing regmap\n");
 
+	needs_delay = (spi->max_speed_hz > ADXL345_MAX_FREQ_NO_FIFO_DELAY);
 	if (spi->mode & SPI_3WIRE)
-		return adxl345_core_probe(&spi->dev, regmap, adxl345_spi_setup);
+		return adxl345_core_probe(&spi->dev, regmap, needs_delay, adxl345_spi_setup);
 	else
-		return adxl345_core_probe(&spi->dev, regmap, NULL);
+		return adxl345_core_probe(&spi->dev, regmap, needs_delay, NULL);
 }
 
 static const struct adxl345_chip_info adxl345_spi_info = {