@@ -77,6 +77,7 @@
#define YAS530_DATA_BITS 12
#define YAS530_DATA_CENTER BIT(YAS530_DATA_BITS - 1)
#define YAS530_DATA_OVERFLOW (BIT(YAS530_DATA_BITS) - 1)
+#define YAS530_20DEGREES 182 /* Counts starting at -62 °C */
#define YAS532_DEVICE_ID 0x02 /* YAS532/YAS533 (MS-3R/F) */
#define YAS532_VERSION_AB 0 /* YAS532/533 AB (MS-3R/F AB) */
@@ -88,7 +89,7 @@
#define YAS532_DATA_BITS 13
#define YAS532_DATA_CENTER BIT(YAS532_DATA_BITS - 1)
#define YAS532_DATA_OVERFLOW (BIT(YAS532_DATA_BITS) - 1)
-#define YAS532_20DEGREES 390 /* Looks like Kelvin */
+#define YAS532_20DEGREES 390 /* Counts starting at -50 °C */
/* These variant IDs are known from code dumps */
#define YAS537_DEVICE_ID 0x07 /* YAS537 (MS-3T) */
@@ -314,7 +315,7 @@ static s32 yas5xx_linearize(struct yas5xx *yas5xx, u16 val, int axis)
static int yas5xx_get_measure(struct yas5xx *yas5xx, s32 *to, s32 *xo, s32 *yo, s32 *zo)
{
struct yas5xx_calibration *c = &yas5xx->calibration;
- u16 t, x, y1, y2;
+ u16 t_ref, t, x, y1, y2;
/* These are "signed x, signed y1 etc */
s32 sx, sy1, sy2, sy, sz;
int ret;
@@ -329,16 +330,43 @@ static int yas5xx_get_measure(struct yas5xx *yas5xx, s32 *to, s32 *xo, s32 *yo,
sy1 = yas5xx_linearize(yas5xx, y1, 1);
sy2 = yas5xx_linearize(yas5xx, y2, 2);
- /*
- * Temperature compensation for x, y1, y2 respectively:
- *
- * Cx * t
- * x' = x - ------
- * 100
- */
- sx = sx - (c->Cx * t) / 100;
- sy1 = sy1 - (c->Cy1 * t) / 100;
- sy2 = sy2 - (c->Cy2 * t) / 100;
+ /* Set the temperature reference value (unit: counts) */
+ switch (yas5xx->devid) {
+ case YAS530_DEVICE_ID:
+ t_ref = YAS530_20DEGREES;
+ break;
+ case YAS532_DEVICE_ID:
+ t_ref = YAS532_20DEGREES;
+ break;
+ }
+
+ /* Temperature compensation for x, y1, y2 respectively */
+ if (yas5xx->devid == YAS532_DEVICE_ID &&
+ yas5xx->version == YAS532_VERSION_AC) {
+ /*
+ * YAS532 version AC uses the temperature deviation as a
+ * multiplier.
+ *
+ * Cx * (t - t_ref)
+ * x' = x - ----------------
+ * 100
+ */
+ sx = sx - (c->Cx * (t - t_ref)) / 100;
+ sy1 = sy1 - (c->Cy1 * (t - t_ref)) / 100;
+ sy2 = sy2 - (c->Cy2 * (t - t_ref)) / 100;
+ } else {
+ /*
+ * YAS530 and YAS532 version AB use solely the t value as a
+ * multiplier.
+ *
+ * Cx * t
+ * x' = x - ------
+ * 100
+ */
+ sx = sx - (c->Cx * t) / 100;
+ sy1 = sy1 - (c->Cy1 * t) / 100;
+ sy2 = sy2 - (c->Cy2 * t) / 100;
+ }
/*
* Break y1 and y2 into y and z, y1 and y2 are apparently encoding
@@ -347,11 +375,34 @@ static int yas5xx_get_measure(struct yas5xx *yas5xx, s32 *to, s32 *xo, s32 *yo,
sy = sy1 - sy2;
sz = -sy1 - sy2;
- /*
- * FIXME: convert to Celsius? Just guessing this is given
- * as 1/10:s of degrees so multiply by 100 to get millicentigrades.
- */
- *to = t * 100;
+ /* Process temperature readout */
+ switch (yas5xx->devid) {
+ case YAS530_DEVICE_ID:
+ /*
+ * Raw temperature value t is number of counts starting at
+ * -62 °C. Reference value t_ref is the number of counts
+ * between -62 °C and 20 °C (82 °C range).
+ *
+ * Temperature in °C would be (82 / t_ref * t) - 62.
+ *
+ * Contrary to this, perform multiplication first and division
+ * second due to calculating with integers.
+ *
+ * To get a nicer result, calculate with 1/10:s degrees Celsius
+ * and finally multiply by 100 to return milli degrees Celsius.
+ */
+ *to = ((820 * t / t_ref) - 620) * 100;
+ break;
+ case YAS532_DEVICE_ID:
+ /*
+ * Actually same procedure for YAS532 but the starting point is
+ * at -50 °C. Reference value t_ref is the number of counts
+ * between -50 °C and 20 °C (70 °C range).
+ */
+ *to = ((700 * t / t_ref) - 500) * 100;
+ break;
+ }
+
/*
* Calibrate [x,y,z] with some formulas like this:
*
@@ -384,6 +435,7 @@ static int yas5xx_read_raw(struct iio_dev *indio_dev,
int ret;
switch (mask) {
+ case IIO_CHAN_INFO_PROCESSED:
case IIO_CHAN_INFO_RAW:
pm_runtime_get_sync(yas5xx->dev);
ret = yas5xx_get_measure(yas5xx, &t, &x, &y, &z);
@@ -410,11 +462,6 @@ static int yas5xx_read_raw(struct iio_dev *indio_dev,
}
return IIO_VAL_INT;
case IIO_CHAN_INFO_SCALE:
- if (chan->address == 0) {
- /* Temperature is unscaled */
- *val = 1;
- return IIO_VAL_INT;
- }
switch (yas5xx->devid) {
case YAS530_DEVICE_ID:
/*
@@ -513,7 +560,7 @@ static const struct iio_chan_spec yas5xx_channels[] = {
.address = 0,
.scan_index = 0,
.scan_type = {
- .sign = 'u',
+ .sign = 's',
.realbits = 32,
.storagebits = 32,
.endianness = IIO_CPU,
The raw temperature value is a number of counts from a certain starting point. The resolution of the temperature counts is different for the YAS variants. Temperature compensation for YAS532 version AC seems to be handled differently. It uses the deviation from 20 degree Celsius [1] whereas YAS530 and older versions of YAS532 apply solely the t value as a multiplier [2][3]. In funtion yas5xx_read_raw(), add case IIO_CHAN_INFO_PROCESSED. Remove scale of temperature as this isn't applied. Additionally correct sign of temperature channel in iio_chan_spec. It's already defined that way in yas5xx_get_measure() function. [1] https://github.com/msm8916-mainline/android_kernel_qcom_msm8916/blob/GT-I9195I/drivers/iio/magnetometer/yas_mag_drv-yas532.c#L442 [2] https://github.com/NovaFusion/android_kernel_samsung_golden/blob/cm-12.1/drivers/sensor/compass/yas_mag_driver-yas530.c#L881-L883 [3] https://github.com/LineageOS/android_kernel_samsung_msm8930-common/blob/lineage-18.1/drivers/sensors/geomagnetic/yas_mag_driver-yas53x.c#L856-L858 Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jakob Hauser <jahau@rocketmail.com> --- drivers/iio/magnetometer/yamaha-yas530.c | 93 ++++++++++++++++++------ 1 file changed, 70 insertions(+), 23 deletions(-)