@@ -370,4 +370,13 @@ config KEYBOARD_XTKBD
To compile this driver as a module, choose M here: the
module will be called xtkbd.
+config KEYBOARD_ADP5588
+ tristate "ADP5588 I2C QWERTY Keypad and IO Expander"
+ depends on I2C
+ help
+ Say Y here if you want to use a ADP5588 attached to your system I2C bus
+
+ To compile this driver as a module, choose M here: the
+ module will be called adp5588-keys.
+
endif
@@ -5,6 +5,7 @@
# Each configuration option enables a list of files.
obj-$(CONFIG_KEYBOARD_AAED2000) += aaed2000_kbd.o
+obj-$(CONFIG_KEYBOARD_ADP5588) += adp5588-keys.o
obj-$(CONFIG_KEYBOARD_AMIGA) += amikbd.o
obj-$(CONFIG_KEYBOARD_ATARI) += atakbd.o
obj-$(CONFIG_KEYBOARD_ATKBD) += atkbd.o
new file mode 100644
@@ -0,0 +1,356 @@
+/*
+ * File: drivers/input/keyboard/adp5588_keys.c
+ * Description: keypad driver for ADP5588 I2C QWERTY Keypad and IO Expander
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Copyright (C) 2008-2009 Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/workqueue.h>
+#include <linux/errno.h>
+#include <linux/pm.h>
+#include <linux/platform_device.h>
+#include <linux/input.h>
+#include <linux/i2c.h>
+
+#include <linux/i2c/adp5588.h>
+
+ /* Configuration Register1 */
+#define AUTO_INC (1 << 7)
+#define GPIEM_CFG (1 << 6)
+#define OVR_FLOW_M (1 << 5)
+#define INT_CFG (1 << 4)
+#define OVR_FLOW_IEN (1 << 3)
+#define K_LCK_IM (1 << 2)
+#define GPI_IEN (1 << 1)
+#define KE_IEN (1 << 0)
+
+/* Interrupt Status Register */
+#define CMP2_INT (1 << 5)
+#define CMP1_INT (1 << 4)
+#define OVR_FLOW_INT (1 << 3)
+#define K_LCK_INT (1 << 2)
+#define GPI_INT (1 << 1)
+#define KE_INT (1 << 0)
+
+/* Key Lock and Event Counter Register */
+#define K_LCK_EN (1 << 6)
+#define LCK21 0x30
+#define KEC 0xF
+
+/* Key Event Register xy */
+#define KEY_EV_PRESSED (1 << 7)
+#define KEY_EV_MASK (0x7F)
+
+#define KP_SEL(x) (0xFFFF >> (16 - x)) /* 2^x-1 */
+
+#define KEYP_MAX_EVENT 10
+#define DRV_NAME "adp5588-keys"
+
+/*
+ * Early pre 4.0 Silicon required to delay readout by at least 25ms,
+ * since the Event Counter Register updated 25ms after the interrupt
+ * asserted.
+ */
+#define WA_DELAYED_READOUT_REVID(rev) ((rev) < 4)
+
+struct adp5588_kpad {
+ struct i2c_client *client;
+ struct input_dev *input;
+ struct delayed_work work;
+ unsigned revid;
+ unsigned short keycode[ADP5588_KEYMAPSIZE];
+};
+
+static int adp5588_read(struct i2c_client *client, u8 reg)
+{
+ int ret = i2c_smbus_read_byte_data(client, reg);
+
+ if (ret < 0)
+ dev_err(&client->dev, "Read Error\n");
+
+ return ret;
+}
+
+static int adp5588_write(struct i2c_client *client, u8 reg, u8 val)
+{
+ return i2c_smbus_write_byte_data(client, reg, val);
+}
+
+static void adp5588_work(struct work_struct *work)
+{
+ struct adp5588_kpad *kpad = container_of(work,
+ struct adp5588_kpad, work.work);
+ struct i2c_client *client = kpad->client;
+ int i, key, status, ev_cnt;
+
+ status = adp5588_read(client, INT_STAT);
+
+ if (status & OVR_FLOW_INT) /* Unlikely and should never happen */
+ dev_err(&client->dev, "Event Overflow Error\n");
+
+ if (status & KE_INT) {
+ ev_cnt = adp5588_read(client, KEY_LCK_EC_STAT) & KEC;
+ if (ev_cnt) {
+ for (i = 0; i < ev_cnt; i++) {
+ key = adp5588_read(client, Key_EVENTA + i);
+ input_report_key(kpad->input,
+ kpad->keycode[(key & KEY_EV_MASK) - 1],
+ key & KEY_EV_PRESSED);
+ }
+ input_sync(kpad->input);
+ }
+ }
+ adp5588_write(client, INT_STAT, status); /* Status is W1C */
+}
+
+static irqreturn_t adp5588_irq(int irq, void *handle)
+{
+ struct adp5588_kpad *kpad = handle;
+
+ /*
+ * use keventd context to read the event fifo registers
+ * Schedule readout at least 25ms after notification for
+ * REVID < 4
+ */
+
+ schedule_delayed_work(&kpad->work,
+ WA_DELAYED_READOUT_REVID(kpad->revid) ?
+ (unsigned long) msecs_to_jiffies(30) : 0);
+
+ return IRQ_HANDLED;
+}
+
+static int adp5588_setup(struct i2c_client *client)
+{
+ struct adp5588_kpad_platform_data *pdata = client->dev.platform_data;
+ int i, ret;
+
+ ret = adp5588_write(client, KP_GPIO1, KP_SEL(pdata->rows));
+ ret |= adp5588_write(client, KP_GPIO2, KP_SEL(pdata->cols) & 0xFF);
+ ret |= adp5588_write(client, KP_GPIO3, KP_SEL(pdata->cols) >> 8);
+
+ if (pdata->en_keylock) {
+ ret |= adp5588_write(client, UNLOCK1, pdata->unlock_key1);
+ ret |= adp5588_write(client, UNLOCK2, pdata->unlock_key2);
+ ret |= adp5588_write(client, KEY_LCK_EC_STAT, K_LCK_EN);
+ }
+
+ for (i = 0; i < KEYP_MAX_EVENT; i++)
+ ret |= adp5588_read(client, Key_EVENTA);
+
+ ret |= adp5588_write(client, INT_STAT, CMP2_INT | CMP1_INT |
+ OVR_FLOW_INT | K_LCK_INT |
+ GPI_INT | KE_INT); /* Status is W1C */
+
+ ret |= adp5588_write(client, CFG, INT_CFG | OVR_FLOW_IEN | KE_IEN);
+
+ if (ret < 0) {
+ dev_err(&client->dev, "Write Error\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int __devinit adp5588_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct adp5588_kpad *kpad;
+ struct adp5588_kpad_platform_data *pdata = client->dev.platform_data;
+ struct input_dev *input;
+ int ret, i;
+
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_BYTE_DATA)) {
+ dev_err(&client->dev, "SMBUS Byte Data not Supported\n");
+ return -EIO;
+ }
+
+ if (!pdata) {
+ dev_err(&client->dev, "no platform data?\n");
+ return -ENODEV;
+ }
+
+ if (!pdata->rows || !pdata->cols || !pdata->keymap) {
+ dev_err(&client->dev,
+ ": No rows, cols or keymap from pdata\n");
+ return -EINVAL;
+ }
+
+ if (pdata->keymapsize != ADP5588_KEYMAPSIZE) {
+ dev_err(&client->dev, ": Invalid keymapsize\n");
+ return -EINVAL;
+ }
+
+ if (!client->irq) {
+ dev_err(&client->dev, "no IRQ?\n");
+ return -ENODEV;
+ }
+
+ kpad = kzalloc(sizeof(struct adp5588_kpad), GFP_KERNEL);
+ if (!kpad)
+ return -ENOMEM;
+
+ input = input_allocate_device();
+ if (!input) {
+ kfree(kpad);
+ return -ENOMEM;
+ }
+
+ i2c_set_clientdata(client, kpad);
+ kpad->client = client;
+
+ ret = adp5588_read(client, DEV_ID);
+ if (ret < 0) {
+ input_free_device(input);
+ goto out1;
+ }
+
+ kpad->revid = (u8) ret & ADP5588_DEVICE_ID_MASK;
+ INIT_DELAYED_WORK(&kpad->work, adp5588_work);
+
+ kpad->input = input;
+
+ input->name = client->name;
+ input->phys = "adp5588-keys/input0";
+ input->dev.parent = &client->dev;
+
+ input_set_drvdata(input, kpad);
+
+ input->id.bustype = BUS_I2C;
+ input->id.vendor = 0x0001;
+ input->id.product = 0x0001;
+ input->id.version = kpad->revid;
+
+ input->keycodesize = sizeof(unsigned short);
+ input->keycodemax = pdata->keymapsize;
+ input->keycode = kpad->keycode;
+
+ memcpy(kpad->keycode, pdata->keymap,
+ pdata->keymapsize * input->keycodesize);
+
+ /* setup input device */
+ __set_bit(EV_KEY, input->evbit);
+
+ if (pdata->repeat)
+ __set_bit(EV_REP, input->evbit);
+
+ for (i = 0; i < input->keycodemax; i++)
+ __set_bit(kpad->keycode[i] & KEY_MAX, input->keybit);
+ __clear_bit(KEY_RESERVED, input->keybit);
+
+ ret = input_register_device(input);
+ if (ret) {
+ dev_err(&client->dev,
+ ": Unable to register input device (%d)\n", ret);
+ input_free_device(input);
+ goto out1;
+ }
+
+ ret = request_irq(client->irq, adp5588_irq, IRQF_TRIGGER_FALLING |
+ IRQF_DISABLED,
+ client->dev.driver->name, kpad);
+ if (ret) {
+ dev_err(&client->dev, "irq %d busy?\n", client->irq);
+ goto out2;
+ }
+
+ ret = adp5588_setup(client);
+ if (ret)
+ goto out3;
+
+ device_init_wakeup(&client->dev, 1);
+
+ dev_info(&client->dev, "Rev.%d keypad, irq %d\n",
+ kpad->revid, client->irq);
+
+ return ret;
+
+out3:
+ free_irq(client->irq, kpad);
+out2:
+ input_unregister_device(input);
+out1:
+ i2c_set_clientdata(client, NULL);
+ kfree(kpad);
+
+ return ret;
+}
+
+static int __devexit adp5588_remove(struct i2c_client *client)
+{
+ struct adp5588_kpad *kpad = dev_get_drvdata(&client->dev);
+
+ adp5588_write(client, CFG, 0);
+ free_irq(client->irq, kpad);
+ input_unregister_device(kpad->input);
+ i2c_set_clientdata(client, NULL);
+ kfree(kpad);
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int adp5588_suspend(struct i2c_client *client, pm_message_t state)
+{
+ disable_irq(client->irq);
+
+ if (device_may_wakeup(&client->dev))
+ enable_irq_wake(client->irq);
+
+ return 0;
+}
+
+static int adp5588_resume(struct i2c_client *client)
+{
+ if (device_may_wakeup(&client->dev))
+ disable_irq_wake(client->irq);
+
+ enable_irq(client->irq);
+ return 0;
+}
+#else
+# define adp5588_suspend NULL
+# define adp5588_resume NULL
+#endif
+
+static const struct i2c_device_id adp5588_id[] = {
+ { DRV_NAME, 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, adp5588_id);
+
+static struct i2c_driver adp5588_driver = {
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+ .probe = adp5588_probe,
+ .remove = __devexit_p(adp5588_remove),
+ .suspend = adp5588_suspend,
+ .resume = adp5588_resume,
+ .id_table = adp5588_id,
+};
+
+static int __init adp5588_init(void)
+{
+ return i2c_add_driver(&adp5588_driver);
+}
+module_init(adp5588_init);
+
+static void __exit adp5588_exit(void)
+{
+ i2c_del_driver(&adp5588_driver);
+}
+module_exit(adp5588_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>");
+MODULE_DESCRIPTION("ADP5588 Keypad driver");
+MODULE_ALIAS("platform:adp5588-keys");
new file mode 100644
@@ -0,0 +1,92 @@
+/*
+ * Analog Devices ADP5588 I/O Expander and QWERTY Keypad Controller
+ *
+ * Copyright 2009 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef _ADP5588_H
+#define _ADP5588_H
+
+#define DEV_ID 0x00 /* Device ID */
+#define CFG 0x01 /* Configuration Register1 */
+#define INT_STAT 0x02 /* Interrupt Status Register */
+#define KEY_LCK_EC_STAT 0x03 /* Key Lock and Event Counter Register */
+#define Key_EVENTA 0x04 /* Key Event Register A */
+#define Key_EVENTB 0x05 /* Key Event Register B */
+#define Key_EVENTC 0x06 /* Key Event Register C */
+#define Key_EVENTD 0x07 /* Key Event Register D */
+#define Key_EVENTE 0x08 /* Key Event Register E */
+#define Key_EVENTF 0x09 /* Key Event Register F */
+#define Key_EVENTG 0x0A /* Key Event Register G */
+#define Key_EVENTH 0x0B /* Key Event Register H */
+#define Key_EVENTI 0x0C /* Key Event Register I */
+#define Key_EVENTJ 0x0D /* Key Event Register J */
+#define KP_LCK_TMR 0x0E /* Keypad Lock1 to Lock2 Timer */
+#define UNLOCK1 0x0F /* Unlock Key1 */
+#define UNLOCK2 0x10 /* Unlock Key2 */
+#define GPIO_INT_STAT1 0x11 /* GPIO Interrupt Status */
+#define GPIO_INT_STAT2 0x12 /* GPIO Interrupt Status */
+#define GPIO_INT_STAT3 0x13 /* GPIO Interrupt Status */
+#define GPIO_DAT_STAT1 0x14 /* GPIO Data Status, Read twice to clear */
+#define GPIO_DAT_STAT2 0x15 /* GPIO Data Status, Read twice to clear */
+#define GPIO_DAT_STAT3 0x16 /* GPIO Data Status, Read twice to clear */
+#define GPIO_DAT_OUT1 0x17 /* GPIO DATA OUT */
+#define GPIO_DAT_OUT2 0x18 /* GPIO DATA OUT */
+#define GPIO_DAT_OUT3 0x19 /* GPIO DATA OUT */
+#define GPIO_INT_EN1 0x1A /* GPIO Interrupt Enable */
+#define GPIO_INT_EN2 0x1B /* GPIO Interrupt Enable */
+#define GPIO_INT_EN3 0x1C /* GPIO Interrupt Enable */
+#define KP_GPIO1 0x1D /* Keypad or GPIO Selection */
+#define KP_GPIO2 0x1E /* Keypad or GPIO Selection */
+#define KP_GPIO3 0x1F /* Keypad or GPIO Selection */
+#define GPI_EM1 0x20 /* GPI Event Mode 1 */
+#define GPI_EM2 0x21 /* GPI Event Mode 2 */
+#define GPI_EM3 0x22 /* GPI Event Mode 3 */
+#define GPIO_DIR1 0x23 /* GPIO Data Direction */
+#define GPIO_DIR2 0x24 /* GPIO Data Direction */
+#define GPIO_DIR3 0x25 /* GPIO Data Direction */
+#define GPIO_INT_LVL1 0x26 /* GPIO Edge/Level Detect */
+#define GPIO_INT_LVL2 0x27 /* GPIO Edge/Level Detect */
+#define GPIO_INT_LVL3 0x28 /* GPIO Edge/Level Detect */
+#define Debounce_DIS1 0x29 /* Debounce Disable */
+#define Debounce_DIS2 0x2A /* Debounce Disable */
+#define Debounce_DIS3 0x2B /* Debounce Disable */
+#define GPIO_PULL1 0x2C /* GPIO Pull Disable */
+#define GPIO_PULL2 0x2D /* GPIO Pull Disable */
+#define GPIO_PULL3 0x2E /* GPIO Pull Disable */
+#define CMP_CFG_STAT 0x30 /* Comparator Configuration and Status Register */
+#define CMP_CONFG_SENS1 0x31 /* Sensor1 Comparator Configuration Register */
+#define CMP_CONFG_SENS2 0x32 /* L2 Light Sensor Reference Level, Output Falling for Sensor 1 */
+#define CMP1_LVL2_TRIP 0x33 /* L2 Light Sensor Hysteresis (Active when Output Rising) for Sensor 1 */
+#define CMP1_LVL2_HYS 0x34 /* L3 Light Sensor Reference Level, Output Falling For Sensor 1 */
+#define CMP1_LVL3_TRIP 0x35 /* L3 Light Sensor Hysteresis (Active when Output Rising) For Sensor 1 */
+#define CMP1_LVL3_HYS 0x36 /* Sensor 2 Comparator Configuration Register */
+#define CMP2_LVL2_TRIP 0x37 /* L2 Light Sensor Reference Level, Output Falling for Sensor 2 */
+#define CMP2_LVL2_HYS 0x38 /* L2 Light Sensor Hysteresis (Active when Output Rising) for Sensor 2 */
+#define CMP2_LVL3_TRIP 0x39 /* L3 Light Sensor Reference Level, Output Falling For Sensor 2 */
+#define CMP2_LVL3_HYS 0x3A /* L3 Light Sensor Hysteresis (Active when Output Rising) For Sensor 2 */
+#define CMP1_ADC_DAT_R1 0x3B /* Comparator 1 ADC data Register1 */
+#define CMP1_ADC_DAT_R2 0x3C /* Comparator 1 ADC data Register2 */
+#define CMP2_ADC_DAT_R1 0x3D /* Comparator 2 ADC data Register1 */
+#define CMP2_ADC_DAT_R2 0x3E /* Comparator 2 ADC data Register2 */
+
+#define ADP5588_DEVICE_ID_MASK 0xF
+
+/* Put one of these structures in i2c_board_info platform_data */
+
+#define ADP5588_KEYMAPSIZE 80
+
+struct adp5588_kpad_platform_data {
+ int rows; /* Number of rows */
+ int cols; /* Number of columns */
+ const unsigned short *keymap; /* Pointer to keymap */
+ unsigned short keymapsize; /* Keymap size */
+ unsigned repeat:1; /* Enable key repeat */
+ unsigned en_keylock:1; /* Enable Key Lock feature */
+ unsigned short unlock_key1; /* Unlock Key 1 */
+ unsigned short unlock_key2; /* Unlock Key 2 */
+};
+
+#endif