@@ -104,12 +104,8 @@ struct ads7846 {
#endif
u16 model;
- u16 vref_mv;
u16 vref_delay_usecs;
- u16 x_plate_ohms;
- u16 pressure_max;
- bool swap_xy;
bool use_internal;
struct ads7846_packet *packet;
@@ -143,6 +139,9 @@ struct ads7846 {
int gpio_pendown;
void (*wait_for_sync)(void);
+
+ /* platform data from board file or DT */
+ struct ads7846_platform_data *pdata;
};
/* leave chip selected when we're done, for quicker re-select? */
@@ -456,7 +455,7 @@ static inline unsigned vaux_adjust(struct ads7846 *ts, ssize_t v)
unsigned retval = v;
/* external resistors may scale vAUX into 0..vREF */
- retval *= ts->vref_mv;
+ retval *= ts->pdata->vref_mv;
retval = retval >> 12;
return retval;
@@ -515,25 +514,25 @@ static int ads784x_hwmon_register(struct spi_device *spi, struct ads7846 *ts)
/* hwmon sensors need a reference voltage */
switch (ts->model) {
case 7846:
- if (!ts->vref_mv) {
+ if (!ts->pdata->vref_mv) {
dev_dbg(&spi->dev, "assuming 2.5V internal vREF\n");
- ts->vref_mv = 2500;
+ ts->pdata->vref_mv = 2500;
ts->use_internal = true;
}
break;
case 7845:
case 7843:
- if (!ts->vref_mv) {
+ if (!ts->pdata->vref_mv) {
dev_warn(&spi->dev,
"external vREF for ADS%d not specified\n",
- ts->model);
+ ts->pdata->model);
return 0;
}
break;
}
/* different chips have different sensor groups */
- switch (ts->model) {
+ switch (ts->pdata->model) {
case 7846:
ts->attr_group = &ads7846_attr_group;
break;
@@ -544,7 +543,7 @@ static int ads784x_hwmon_register(struct spi_device *spi, struct ads7846 *ts)
ts->attr_group = &ads7843_attr_group;
break;
default:
- dev_dbg(&spi->dev, "ADS%d not recognized\n", ts->model);
+ dev_dbg(&spi->dev, "ADS%d not recognized\n", ts->pdata->model);
return 0;
}
@@ -700,7 +699,7 @@ static int ads7846_get_value(struct ads7846 *ts, struct spi_message *m)
struct spi_transfer *t =
list_entry(m->transfers.prev, struct spi_transfer, transfer_list);
- if (ts->model == 7845) {
+ if (ts->pdata->model == 7845) {
return be16_to_cpup((__be16 *)&(((char*)t->rx_buf)[1])) >> 3;
} else {
/*
@@ -776,6 +775,7 @@ static void ads7846_read_state(struct ads7846 *ts)
static void ads7846_report_state(struct ads7846 *ts)
{
struct ads7846_packet *packet = ts->packet;
+ struct ads7846_platform_data *pdata = ts->pdata;
unsigned int Rt;
u16 x, y, z1, z2;
@@ -784,7 +784,7 @@ static void ads7846_report_state(struct ads7846 *ts)
* from on-the-wire format as part of debouncing to get stable
* readings.
*/
- if (ts->model == 7845) {
+ if (pdata->model == 7845) {
x = *(u16 *)packet->tc.x_buf;
y = *(u16 *)packet->tc.y_buf;
z1 = 0;
@@ -800,11 +800,11 @@ static void ads7846_report_state(struct ads7846 *ts)
if (x == MAX_12BIT)
x = 0;
- if (ts->model == 7843) {
- Rt = ts->pressure_max / 2;
- } else if (ts->model == 7845) {
+ if (pdata->model == 7843) {
+ Rt = pdata->pressure_max / 2;
+ } else if (pdata->model == 7845) {
if (get_pendown_state(ts))
- Rt = ts->pressure_max / 2;
+ Rt = pdata->pressure_max / 2;
else
Rt = 0;
dev_vdbg(&ts->spi->dev, "x/y: %d/%d, PD %d\n", x, y, Rt);
@@ -813,7 +813,7 @@ static void ads7846_report_state(struct ads7846 *ts)
Rt = z2;
Rt -= z1;
Rt *= x;
- Rt *= ts->x_plate_ohms;
+ Rt *= pdata->x_plate_ohms;
Rt /= z1;
Rt = (Rt + 2047) >> 12;
} else {
@@ -825,7 +825,7 @@ static void ads7846_report_state(struct ads7846 *ts)
* the maximum. Don't report it to user space, repeat at least
* once more the measurement
*/
- if (packet->tc.ignore || Rt > ts->pressure_max) {
+ if (packet->tc.ignore || Rt > pdata->pressure_max) {
dev_vdbg(&ts->spi->dev, "ignored %d pressure %d\n",
packet->tc.ignore, Rt);
return;
@@ -853,7 +853,7 @@ static void ads7846_report_state(struct ads7846 *ts)
if (Rt) {
struct input_dev *input = ts->input;
- if (ts->swap_xy)
+ if (pdata->swap_xy)
swap(x, y);
if (!ts->pendown) {
@@ -864,7 +864,7 @@ static void ads7846_report_state(struct ads7846 *ts)
input_report_abs(input, ABS_X, x);
input_report_abs(input, ABS_Y, y);
- input_report_abs(input, ABS_PRESSURE, ts->pressure_max - Rt);
+ input_report_abs(input, ABS_PRESSURE, pdata->pressure_max - Rt);
input_sync(input);
dev_vdbg(&ts->spi->dev, "%4d/%4d/%4d\n", x, y, Rt);
@@ -963,7 +963,7 @@ static SIMPLE_DEV_PM_OPS(ads7846_pm, ads7846_suspend, ads7846_resume);
static int ads7846_setup_pendown(struct spi_device *spi,
struct ads7846 *ts)
{
- struct ads7846_platform_data *pdata = spi->dev.platform_data;
+ struct ads7846_platform_data *pdata = ts->pdata;
int err;
/*
@@ -1003,20 +1003,20 @@ static int ads7846_setup_pendown(struct spi_device *spi,
* use formula #2 for pressure, not #3.
*/
static void ads7846_setup_spi_msg(struct ads7846 *ts,
- const struct ads7846_platform_data *pdata)
+ struct ads7846_platform_data *pdata)
{
struct spi_message *m = &ts->msg[0];
struct spi_transfer *x = ts->xfer;
struct ads7846_packet *packet = ts->packet;
int vref = pdata->keep_vref_on;
- if (ts->model == 7873) {
+ if (pdata->model == 7873) {
/*
* The AD7873 is almost identical to the ADS7846
* keep VREF off during differential/ratiometric
* conversion modes.
*/
- ts->model = 7846;
+ pdata->model = 7846;
vref = 0;
}
@@ -1024,7 +1024,7 @@ static void ads7846_setup_spi_msg(struct ads7846 *ts,
spi_message_init(m);
m->context = ts;
- if (ts->model == 7845) {
+ if (pdata->model == 7845) {
packet->read_y_cmd[0] = READ_Y(vref);
packet->read_y_cmd[1] = 0;
packet->read_y_cmd[2] = 0;
@@ -1069,7 +1069,7 @@ static void ads7846_setup_spi_msg(struct ads7846 *ts,
spi_message_init(m);
m->context = ts;
- if (ts->model == 7845) {
+ if (pdata->model == 7845) {
x++;
packet->read_x_cmd[0] = READ_X(vref);
packet->read_x_cmd[1] = 0;
@@ -1108,7 +1108,7 @@ static void ads7846_setup_spi_msg(struct ads7846 *ts,
}
/* turn y+ off, x- on; we'll use formula #2 */
- if (ts->model == 7846) {
+ if (pdata->model == 7846) {
ts->msg_count++;
m++;
spi_message_init(m);
@@ -1178,7 +1178,7 @@ static void ads7846_setup_spi_msg(struct ads7846 *ts,
spi_message_init(m);
m->context = ts;
- if (ts->model == 7845) {
+ if (pdata->model == 7845) {
x++;
packet->pwrdown_cmd[0] = PWRDOWN;
packet->pwrdown_cmd[1] = 0;
@@ -1247,19 +1247,27 @@ static int ads7846_probe(struct spi_device *spi)
spi_set_drvdata(spi, ts);
+ ts->pdata = pdata;
ts->packet = packet;
ts->spi = spi;
ts->input = input_dev;
- ts->vref_mv = pdata->vref_mv;
- ts->swap_xy = pdata->swap_xy;
mutex_init(&ts->lock);
init_waitqueue_head(&ts->wait);
- ts->model = pdata->model ? : 7846;
- ts->vref_delay_usecs = pdata->vref_delay_usecs ? : 100;
- ts->x_plate_ohms = pdata->x_plate_ohms ? : 400;
- ts->pressure_max = pdata->pressure_max ? : ~0;
+ /* pdata fallback defaults */
+
+ if (!pdata->model)
+ pdata->model = 7846;
+
+ if (!pdata->vref_delay_usecs)
+ pdata->vref_delay_usecs = 100;
+
+ if (!pdata->x_plate_ohms)
+ pdata->x_plate_ohms = 400;
+
+ if (!pdata->pressure_max)
+ pdata->pressure_max = ~0;
if (pdata->filter != NULL) {
if (pdata->filter_init != NULL) {
Allocate a copy of the pdata, and keep a pointer to it in the private struct ads7846. Also, kill some members that used to be in both structs. This is needed for the upcoming DT support. Signed-off-by: Daniel Mack <zonque@gmail.com> --- Hi Dmitry, this is the alternative approach, as described eariler in our email thread. It works equally well. Thanks for having another look. Daniel drivers/input/touchscreen/ads7846.c | 78 ++++++++++++++++++++----------------- 1 file changed, 43 insertions(+), 35 deletions(-)