diff --git a/drivers/input/mouse/Makefile b/drivers/input/mouse/Makefile
index 560003d..8bd950d 100644
--- a/drivers/input/mouse/Makefile
+++ b/drivers/input/mouse/Makefile
@@ -8,7 +8,7 @@ obj-$(CONFIG_MOUSE_AMIGA)		+= amimouse.o
 obj-$(CONFIG_MOUSE_APPLETOUCH)		+= appletouch.o
 obj-$(CONFIG_MOUSE_ATARI)		+= atarimouse.o
 obj-$(CONFIG_MOUSE_BCM5974)		+= bcm5974.o
-obj-$(CONFIG_MOUSE_CYAPA)		+= cyapa.o
+obj-$(CONFIG_MOUSE_CYAPA)		+= cyapatp.o
 obj-$(CONFIG_MOUSE_ELAN_I2C)		+= elan_i2c.o
 obj-$(CONFIG_MOUSE_GPIO)		+= gpio_mouse.o
 obj-$(CONFIG_MOUSE_INPORT)		+= inport.o
@@ -24,6 +24,7 @@ obj-$(CONFIG_MOUSE_SYNAPTICS_I2C)	+= synaptics_i2c.o
 obj-$(CONFIG_MOUSE_SYNAPTICS_USB)	+= synaptics_usb.o
 obj-$(CONFIG_MOUSE_VSXXXAA)		+= vsxxxaa.o
 
+cyapatp-objs := cyapa.o cyapa_gen3.o
 psmouse-objs := psmouse-base.o synaptics.o focaltech.o
 
 psmouse-$(CONFIG_MOUSE_PS2_ALPS)	+= alps.o
diff --git a/drivers/input/mouse/cyapa.c b/drivers/input/mouse/cyapa.c
index 1bece8c..37b1e37 100644
--- a/drivers/input/mouse/cyapa.c
+++ b/drivers/input/mouse/cyapa.c
@@ -20,408 +20,127 @@
 #include <linux/input/mt.h>
 #include <linux/interrupt.h>
 #include <linux/module.h>
+#include <linux/mutex.h>
 #include <linux/slab.h>
+#include <linux/uaccess.h>
+#include "cyapa.h"
 
-/* APA trackpad firmware generation */
-#define CYAPA_GEN3   0x03   /* support MT-protocol B with tracking ID. */
-
-#define CYAPA_NAME   "Cypress APA Trackpad (cyapa)"
-
-/* commands for read/write registers of Cypress trackpad */
-#define CYAPA_CMD_SOFT_RESET       0x00
-#define CYAPA_CMD_POWER_MODE       0x01
-#define CYAPA_CMD_DEV_STATUS       0x02
-#define CYAPA_CMD_GROUP_DATA       0x03
-#define CYAPA_CMD_GROUP_CMD        0x04
-#define CYAPA_CMD_GROUP_QUERY      0x05
-#define CYAPA_CMD_BL_STATUS        0x06
-#define CYAPA_CMD_BL_HEAD          0x07
-#define CYAPA_CMD_BL_CMD           0x08
-#define CYAPA_CMD_BL_DATA          0x09
-#define CYAPA_CMD_BL_ALL           0x0a
-#define CYAPA_CMD_BLK_PRODUCT_ID   0x0b
-#define CYAPA_CMD_BLK_HEAD         0x0c
-
-/* report data start reg offset address. */
-#define DATA_REG_START_OFFSET  0x0000
-
-#define BL_HEAD_OFFSET 0x00
-#define BL_DATA_OFFSET 0x10
-
-/*
- * Operational Device Status Register
- *
- * bit 7: Valid interrupt source
- * bit 6 - 4: Reserved
- * bit 3 - 2: Power status
- * bit 1 - 0: Device status
- */
-#define REG_OP_STATUS     0x00
-#define OP_STATUS_SRC     0x80
-#define OP_STATUS_POWER   0x0c
-#define OP_STATUS_DEV     0x03
-#define OP_STATUS_MASK (OP_STATUS_SRC | OP_STATUS_POWER | OP_STATUS_DEV)
-
-/*
- * Operational Finger Count/Button Flags Register
- *
- * bit 7 - 4: Number of touched finger
- * bit 3: Valid data
- * bit 2: Middle Physical Button
- * bit 1: Right Physical Button
- * bit 0: Left physical Button
- */
-#define REG_OP_DATA1       0x01
-#define OP_DATA_VALID      0x08
-#define OP_DATA_MIDDLE_BTN 0x04
-#define OP_DATA_RIGHT_BTN  0x02
-#define OP_DATA_LEFT_BTN   0x01
-#define OP_DATA_BTN_MASK (OP_DATA_MIDDLE_BTN | OP_DATA_RIGHT_BTN | \
-			  OP_DATA_LEFT_BTN)
-
-/*
- * Bootloader Status Register
- *
- * bit 7: Busy
- * bit 6 - 5: Reserved
- * bit 4: Bootloader running
- * bit 3 - 1: Reserved
- * bit 0: Checksum valid
- */
-#define REG_BL_STATUS        0x01
-#define BL_STATUS_BUSY       0x80
-#define BL_STATUS_RUNNING    0x10
-#define BL_STATUS_DATA_VALID 0x08
-#define BL_STATUS_CSUM_VALID 0x01
-
-/*
- * Bootloader Error Register
- *
- * bit 7: Invalid
- * bit 6: Invalid security key
- * bit 5: Bootloading
- * bit 4: Command checksum
- * bit 3: Flash protection error
- * bit 2: Flash checksum error
- * bit 1 - 0: Reserved
- */
-#define REG_BL_ERROR         0x02
-#define BL_ERROR_INVALID     0x80
-#define BL_ERROR_INVALID_KEY 0x40
-#define BL_ERROR_BOOTLOADING 0x20
-#define BL_ERROR_CMD_CSUM    0x10
-#define BL_ERROR_FLASH_PROT  0x08
-#define BL_ERROR_FLASH_CSUM  0x04
-
-#define BL_STATUS_SIZE  3  /* length of bootloader status registers */
-#define BLK_HEAD_BYTES 32
-
-#define PRODUCT_ID_SIZE  16
-#define QUERY_DATA_SIZE  27
-#define REG_PROTOCOL_GEN_QUERY_OFFSET  20
-
-#define REG_OFFSET_DATA_BASE     0x0000
-#define REG_OFFSET_COMMAND_BASE  0x0028
-#define REG_OFFSET_QUERY_BASE    0x002a
-
-#define CAPABILITY_LEFT_BTN_MASK	(0x01 << 3)
-#define CAPABILITY_RIGHT_BTN_MASK	(0x01 << 4)
-#define CAPABILITY_MIDDLE_BTN_MASK	(0x01 << 5)
-#define CAPABILITY_BTN_MASK  (CAPABILITY_LEFT_BTN_MASK | \
-			      CAPABILITY_RIGHT_BTN_MASK | \
-			      CAPABILITY_MIDDLE_BTN_MASK)
-
-#define CYAPA_OFFSET_SOFT_RESET  REG_OFFSET_COMMAND_BASE
-
-#define REG_OFFSET_POWER_MODE (REG_OFFSET_COMMAND_BASE + 1)
-
-#define PWR_MODE_MASK   0xfc
-#define PWR_MODE_FULL_ACTIVE (0x3f << 2)
-#define PWR_MODE_IDLE        (0x05 << 2) /* default sleep time is 50 ms. */
-#define PWR_MODE_OFF         (0x00 << 2)
-
-#define PWR_STATUS_MASK      0x0c
-#define PWR_STATUS_ACTIVE    (0x03 << 2)
-#define PWR_STATUS_IDLE      (0x02 << 2)
-#define PWR_STATUS_OFF       (0x00 << 2)
-
-/*
- * CYAPA trackpad device states.
- * Used in register 0x00, bit1-0, DeviceStatus field.
- * Other values indicate device is in an abnormal state and must be reset.
- */
-#define CYAPA_DEV_NORMAL  0x03
-#define CYAPA_DEV_BUSY    0x01
-
-enum cyapa_state {
-	CYAPA_STATE_OP,
-	CYAPA_STATE_BL_IDLE,
-	CYAPA_STATE_BL_ACTIVE,
-	CYAPA_STATE_BL_BUSY,
-	CYAPA_STATE_NO_DEVICE,
-};
-
-
-struct cyapa_touch {
-	/*
-	 * high bits or x/y position value
-	 * bit 7 - 4: high 4 bits of x position value
-	 * bit 3 - 0: high 4 bits of y position value
-	 */
-	u8 xy_hi;
-	u8 x_lo;  /* low 8 bits of x position value. */
-	u8 y_lo;  /* low 8 bits of y position value. */
-	u8 pressure;
-	/* id range is 1 - 15.  It is incremented with every new touch. */
-	u8 id;
-} __packed;
-
-/* The touch.id is used as the MT slot id, thus max MT slot is 15 */
-#define CYAPA_MAX_MT_SLOTS  15
-
-struct cyapa_reg_data {
-	/*
-	 * bit 0 - 1: device status
-	 * bit 3 - 2: power mode
-	 * bit 6 - 4: reserved
-	 * bit 7: interrupt valid bit
-	 */
-	u8 device_status;
-	/*
-	 * bit 7 - 4: number of fingers currently touching pad
-	 * bit 3: valid data check bit
-	 * bit 2: middle mechanism button state if exists
-	 * bit 1: right mechanism button state if exists
-	 * bit 0: left mechanism button state if exists
-	 */
-	u8 finger_btn;
-	/* CYAPA reports up to 5 touches per packet. */
-	struct cyapa_touch touches[5];
-} __packed;
-
-/* The main device structure */
-struct cyapa {
-	enum cyapa_state state;
-
-	struct i2c_client *client;
-	struct input_dev *input;
-	char phys[32];	/* device physical location */
-	bool irq_wake;  /* irq wake is enabled */
-	bool smbus;
-
-	/* read from query data region. */
-	char product_id[16];
-	u8 btn_capability;
-	u8 gen;
-	int max_abs_x;
-	int max_abs_y;
-	int physical_size_x;
-	int physical_size_y;
-};
-
-static const u8 bl_deactivate[] = { 0x00, 0xff, 0x3b, 0x00, 0x01, 0x02, 0x03,
-		0x04, 0x05, 0x06, 0x07 };
-static const u8 bl_exit[] = { 0x00, 0xff, 0xa5, 0x00, 0x01, 0x02, 0x03, 0x04,
-		0x05, 0x06, 0x07 };
-
-struct cyapa_cmd_len {
-	u8 cmd;
-	u8 len;
-};
 
 #define CYAPA_ADAPTER_FUNC_NONE   0
 #define CYAPA_ADAPTER_FUNC_I2C    1
 #define CYAPA_ADAPTER_FUNC_SMBUS  2
 #define CYAPA_ADAPTER_FUNC_BOTH   3
 
-/*
- * macros for SMBus communication
- */
-#define SMBUS_READ   0x01
-#define SMBUS_WRITE 0x00
-#define SMBUS_ENCODE_IDX(cmd, idx) ((cmd) | (((idx) & 0x03) << 1))
-#define SMBUS_ENCODE_RW(cmd, rw) ((cmd) | ((rw) & 0x01))
-#define SMBUS_BYTE_BLOCK_CMD_MASK 0x80
-#define SMBUS_GROUP_BLOCK_CMD_MASK 0x40
-
- /* for byte read/write command */
-#define CMD_RESET 0
-#define CMD_POWER_MODE 1
-#define CMD_DEV_STATUS 2
-#define SMBUS_BYTE_CMD(cmd) (((cmd) & 0x3f) << 1)
-#define CYAPA_SMBUS_RESET SMBUS_BYTE_CMD(CMD_RESET)
-#define CYAPA_SMBUS_POWER_MODE SMBUS_BYTE_CMD(CMD_POWER_MODE)
-#define CYAPA_SMBUS_DEV_STATUS SMBUS_BYTE_CMD(CMD_DEV_STATUS)
-
- /* for group registers read/write command */
-#define REG_GROUP_DATA 0
-#define REG_GROUP_CMD 2
-#define REG_GROUP_QUERY 3
-#define SMBUS_GROUP_CMD(grp) (0x80 | (((grp) & 0x07) << 3))
-#define CYAPA_SMBUS_GROUP_DATA SMBUS_GROUP_CMD(REG_GROUP_DATA)
-#define CYAPA_SMBUS_GROUP_CMD SMBUS_GROUP_CMD(REG_GROUP_CMD)
-#define CYAPA_SMBUS_GROUP_QUERY SMBUS_GROUP_CMD(REG_GROUP_QUERY)
-
- /* for register block read/write command */
-#define CMD_BL_STATUS 0
-#define CMD_BL_HEAD 1
-#define CMD_BL_CMD 2
-#define CMD_BL_DATA 3
-#define CMD_BL_ALL 4
-#define CMD_BLK_PRODUCT_ID 5
-#define CMD_BLK_HEAD 6
-#define SMBUS_BLOCK_CMD(cmd) (0xc0 | (((cmd) & 0x1f) << 1))
-
-/* register block read/write command in bootloader mode */
-#define CYAPA_SMBUS_BL_STATUS SMBUS_BLOCK_CMD(CMD_BL_STATUS)
-#define CYAPA_SMBUS_BL_HEAD SMBUS_BLOCK_CMD(CMD_BL_HEAD)
-#define CYAPA_SMBUS_BL_CMD SMBUS_BLOCK_CMD(CMD_BL_CMD)
-#define CYAPA_SMBUS_BL_DATA SMBUS_BLOCK_CMD(CMD_BL_DATA)
-#define CYAPA_SMBUS_BL_ALL SMBUS_BLOCK_CMD(CMD_BL_ALL)
-
-/* register block read/write command in operational mode */
-#define CYAPA_SMBUS_BLK_PRODUCT_ID SMBUS_BLOCK_CMD(CMD_BLK_PRODUCT_ID)
-#define CYAPA_SMBUS_BLK_HEAD SMBUS_BLOCK_CMD(CMD_BLK_HEAD)
-
-static const struct cyapa_cmd_len cyapa_i2c_cmds[] = {
-	{ CYAPA_OFFSET_SOFT_RESET, 1 },
-	{ REG_OFFSET_COMMAND_BASE + 1, 1 },
-	{ REG_OFFSET_DATA_BASE, 1 },
-	{ REG_OFFSET_DATA_BASE, sizeof(struct cyapa_reg_data) },
-	{ REG_OFFSET_COMMAND_BASE, 0 },
-	{ REG_OFFSET_QUERY_BASE, QUERY_DATA_SIZE },
-	{ BL_HEAD_OFFSET, 3 },
-	{ BL_HEAD_OFFSET, 16 },
-	{ BL_HEAD_OFFSET, 16 },
-	{ BL_DATA_OFFSET, 16 },
-	{ BL_HEAD_OFFSET, 32 },
-	{ REG_OFFSET_QUERY_BASE, PRODUCT_ID_SIZE },
-	{ REG_OFFSET_DATA_BASE, 32 }
-};
+const char product_id[] = "CYTRA";
 
-static const struct cyapa_cmd_len cyapa_smbus_cmds[] = {
-	{ CYAPA_SMBUS_RESET, 1 },
-	{ CYAPA_SMBUS_POWER_MODE, 1 },
-	{ CYAPA_SMBUS_DEV_STATUS, 1 },
-	{ CYAPA_SMBUS_GROUP_DATA, sizeof(struct cyapa_reg_data) },
-	{ CYAPA_SMBUS_GROUP_CMD, 2 },
-	{ CYAPA_SMBUS_GROUP_QUERY, QUERY_DATA_SIZE },
-	{ CYAPA_SMBUS_BL_STATUS, 3 },
-	{ CYAPA_SMBUS_BL_HEAD, 16 },
-	{ CYAPA_SMBUS_BL_CMD, 16 },
-	{ CYAPA_SMBUS_BL_DATA, 16 },
-	{ CYAPA_SMBUS_BL_ALL, 32 },
-	{ CYAPA_SMBUS_BLK_PRODUCT_ID, PRODUCT_ID_SIZE },
-	{ CYAPA_SMBUS_BLK_HEAD, 16 },
-};
+static int cyapa_reinitialize(struct cyapa *cyapa);
 
-static ssize_t cyapa_i2c_reg_read_block(struct cyapa *cyapa, u8 reg, size_t len,
-					u8 *values)
+static inline bool cyapa_is_bootloader_mode(struct cyapa *cyapa)
 {
-	return i2c_smbus_read_i2c_block_data(cyapa->client, reg, len, values);
+	if (cyapa->gen == CYAPA_GEN5 && cyapa->state == CYAPA_STATE_GEN5_BL)
+		return true;
+
+	if (cyapa->gen == CYAPA_GEN3 &&
+		cyapa->state >= CYAPA_STATE_BL_BUSY &&
+		cyapa->state <= CYAPA_STATE_BL_ACTIVE)
+		return true;
+
+	return false;
 }
 
-static ssize_t cyapa_i2c_reg_write_block(struct cyapa *cyapa, u8 reg,
-					 size_t len, const u8 *values)
+static inline bool cyapa_is_operational_mode(struct cyapa *cyapa)
 {
-	return i2c_smbus_write_i2c_block_data(cyapa->client, reg, len, values);
+	if (cyapa->gen == CYAPA_GEN5 && cyapa->state == CYAPA_STATE_GEN5_APP)
+		return true;
+
+	if (cyapa->gen == CYAPA_GEN3 && cyapa->state == CYAPA_STATE_OP)
+		return true;
+
+	return false;
 }
 
-/*
- * cyapa_smbus_read_block - perform smbus block read command
- * @cyapa  - private data structure of the driver
- * @cmd    - the properly encoded smbus command
- * @len    - expected length of smbus command result
- * @values - buffer to store smbus command result
- *
- * Returns negative errno, else the number of bytes written.
- *
- * Note:
- * In trackpad device, the memory block allocated for I2C register map
- * is 256 bytes, so the max read block for I2C bus is 256 bytes.
- */
-static ssize_t cyapa_smbus_read_block(struct cyapa *cyapa, u8 cmd, size_t len,
-				      u8 *values)
+/* Returns 0 on success, else negative errno on failure. */
+static ssize_t cyapa_i2c_read(struct cyapa *cyapa, u8 reg, size_t len,
+					u8 *values)
 {
-	ssize_t ret;
-	u8 index;
-	u8 smbus_cmd;
-	u8 *buf;
 	struct i2c_client *client = cyapa->client;
+	struct i2c_msg msgs[] = {
+		{
+			.addr = client->addr,
+			.flags = 0,
+			.len = 1,
+			.buf = &reg,
+		},
+		{
+			.addr = client->addr,
+			.flags = I2C_M_RD,
+			.len = len,
+			.buf = values,
+		},
+	};
+	int ret;
 
-	if (!(SMBUS_BYTE_BLOCK_CMD_MASK & cmd))
-		return -EINVAL;
-
-	if (SMBUS_GROUP_BLOCK_CMD_MASK & cmd) {
-		/* read specific block registers command. */
-		smbus_cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ);
-		ret = i2c_smbus_read_block_data(client, smbus_cmd, values);
-		goto out;
-	}
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
 
-	ret = 0;
-	for (index = 0; index * I2C_SMBUS_BLOCK_MAX < len; index++) {
-		smbus_cmd = SMBUS_ENCODE_IDX(cmd, index);
-		smbus_cmd = SMBUS_ENCODE_RW(smbus_cmd, SMBUS_READ);
-		buf = values + I2C_SMBUS_BLOCK_MAX * index;
-		ret = i2c_smbus_read_block_data(client, smbus_cmd, buf);
-		if (ret < 0)
-			goto out;
-	}
+	if (ret != ARRAY_SIZE(msgs))
+		return ret < 0 ? ret : -EIO;
 
-out:
-	return ret > 0 ? len : ret;
+	return 0;
 }
 
-static s32 cyapa_read_byte(struct cyapa *cyapa, u8 cmd_idx)
+/**
+ * cyapa_i2c_write - Execute i2c block data write operation
+ * @cyapa: Handle to this driver
+ * @ret: Offset of the data to written in the register map
+ * @len: number of bytes to write
+ * @values: Data to be written
+ *
+ * Return negative errno code on error; return zero when success.
+ */
+static ssize_t cyapa_i2c_write(struct cyapa *cyapa, u8 reg,
+					 size_t len, const void *values)
 {
-	u8 cmd;
+	struct i2c_client *client = cyapa->client;
+	char buf[32];
+	int ret;
 
-	if (cyapa->smbus) {
-		cmd = cyapa_smbus_cmds[cmd_idx].cmd;
-		cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ);
-	} else {
-		cmd = cyapa_i2c_cmds[cmd_idx].cmd;
-	}
-	return i2c_smbus_read_byte_data(cyapa->client, cmd);
-}
+	if (len > sizeof(buf) - 1)
+		return -ENOMEM;
 
-static s32 cyapa_write_byte(struct cyapa *cyapa, u8 cmd_idx, u8 value)
-{
-	u8 cmd;
+	buf[0] = reg;
+	memcpy(&buf[1], values, len);
 
-	if (cyapa->smbus) {
-		cmd = cyapa_smbus_cmds[cmd_idx].cmd;
-		cmd = SMBUS_ENCODE_RW(cmd, SMBUS_WRITE);
-	} else {
-		cmd = cyapa_i2c_cmds[cmd_idx].cmd;
-	}
-	return i2c_smbus_write_byte_data(cyapa->client, cmd, value);
+	ret = i2c_master_send(client, buf, len + 1);
+	if (ret != len + 1)
+		return ret < 0 ? ret : -EIO;
+
+	return 0;
 }
 
-static ssize_t cyapa_read_block(struct cyapa *cyapa, u8 cmd_idx, u8 *values)
+static u8 cyapa_check_adapter_functionality(struct i2c_client *client)
 {
-	u8 cmd;
-	size_t len;
+	u8 ret = CYAPA_ADAPTER_FUNC_NONE;
 
-	if (cyapa->smbus) {
-		cmd = cyapa_smbus_cmds[cmd_idx].cmd;
-		len = cyapa_smbus_cmds[cmd_idx].len;
-		return cyapa_smbus_read_block(cyapa, cmd, len, values);
-	} else {
-		cmd = cyapa_i2c_cmds[cmd_idx].cmd;
-		len = cyapa_i2c_cmds[cmd_idx].len;
-		return cyapa_i2c_reg_read_block(cyapa, cmd, len, values);
-	}
+	if (i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
+		ret |= CYAPA_ADAPTER_FUNC_I2C;
+	if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA |
+				     I2C_FUNC_SMBUS_BLOCK_DATA |
+				     I2C_FUNC_SMBUS_I2C_BLOCK))
+		ret |= CYAPA_ADAPTER_FUNC_SMBUS;
+	return ret;
 }
 
 /*
  * Query device for its current operating state.
- *
  */
 static int cyapa_get_state(struct cyapa *cyapa)
 {
 	u8 status[BL_STATUS_SIZE];
+	u8 cmd[32];
+	/* The i2c address of gen4 and gen5 trackpad device must be even. */
+	bool even_addr = ((cyapa->client->addr & 0x0001) == 0);
+	bool smbus = false;
+	int retries = 2;
 	int error;
 
 	cyapa->state = CYAPA_STATE_NO_DEVICE;
@@ -433,39 +152,66 @@ static int cyapa_get_state(struct cyapa *cyapa)
 	 *
 	 */
 	error = cyapa_i2c_reg_read_block(cyapa, BL_HEAD_OFFSET, BL_STATUS_SIZE,
-				         status);
+				       status);
 
 	/*
 	 * On smbus systems in OP mode, the i2c_reg_read will fail with
 	 * -ETIMEDOUT.  In this case, try again using the smbus equivalent
 	 * command.  This should return a BL_HEAD indicating CYAPA_STATE_OP.
 	 */
-	if (cyapa->smbus && (error == -ETIMEDOUT || error == -ENXIO))
-		error = cyapa_read_block(cyapa, CYAPA_CMD_BL_STATUS, status);
+	if (cyapa->smbus && (error == -ETIMEDOUT || error == -ENXIO)) {
+		if (!even_addr)
+			error = cyapa_read_block(cyapa,
+					CYAPA_CMD_BL_STATUS, status);
+		smbus = true;
+	}
 
 	if (error != BL_STATUS_SIZE)
 		goto error;
 
-	if ((status[REG_OP_STATUS] & OP_STATUS_SRC) == OP_STATUS_SRC) {
-		switch (status[REG_OP_STATUS] & OP_STATUS_DEV) {
-		case CYAPA_DEV_NORMAL:
-		case CYAPA_DEV_BUSY:
-			cyapa->state = CYAPA_STATE_OP;
-			break;
-		default:
-			error = -EAGAIN;
-			goto error;
+	/*
+	 * Detect trackpad protocol based on characteristic registers and bits.
+	 */
+	do {
+		cyapa->status[REG_OP_STATUS] = status[REG_OP_STATUS];
+		cyapa->status[REG_BL_STATUS] = status[REG_BL_STATUS];
+		cyapa->status[REG_BL_ERROR] = status[REG_BL_ERROR];
+
+		if (cyapa->gen == CYAPA_GEN_UNKNOWN ||
+				cyapa->gen == CYAPA_GEN3) {
+			error = cyapa_gen3_ops.state_parse(cyapa,
+					status, BL_STATUS_SIZE);
+			if (!error)
+				goto out_detected;
 		}
-	} else {
-		if (status[REG_BL_STATUS] & BL_STATUS_BUSY)
-			cyapa->state = CYAPA_STATE_BL_BUSY;
-		else if (status[REG_BL_ERROR] & BL_ERROR_BOOTLOADING)
-			cyapa->state = CYAPA_STATE_BL_ACTIVE;
-		else
-			cyapa->state = CYAPA_STATE_BL_IDLE;
-	}
 
+		/*
+		 * Write 0x00 0x00 to trackpad device to force update its
+		 * status, then redo the detection again.
+		 */
+		if (!smbus) {
+			cmd[0] = 0x00;
+			cmd[1] = 0x00;
+			error = cyapa_i2c_write(cyapa, 0, 2, cmd);
+			if (error)
+				goto error;
+
+			msleep(50);
+
+			error = cyapa_i2c_read(cyapa, BL_HEAD_OFFSET,
+					BL_STATUS_SIZE, status);
+			if (error)
+				goto error;
+		}
+	} while (--retries > 0 && !smbus);
+
+	goto error;
+
+out_detected:
+	if (cyapa->state <= CYAPA_STATE_BL_BUSY)
+		return -EAGAIN;
 	return 0;
+
 error:
 	return (error < 0) ? error : -EAGAIN;
 }
@@ -482,143 +228,23 @@ error:
  * Returns:
  *   0 when the device eventually responds with a valid non-busy state.
  *   -ETIMEDOUT if device never responds (too many -EAGAIN)
- *   < 0    other errors
+ *   -EAGAIN    if bootload is busy, or unknown state.
+ *   < 0        other errors
  */
-static int cyapa_poll_state(struct cyapa *cyapa, unsigned int timeout)
+int cyapa_poll_state(struct cyapa *cyapa, unsigned int timeout)
 {
 	int error;
 	int tries = timeout / 100;
 
-	error = cyapa_get_state(cyapa);
-	while ((error || cyapa->state >= CYAPA_STATE_BL_BUSY) && tries--) {
-		msleep(100);
+	do {
 		error = cyapa_get_state(cyapa);
-	}
-	return (error == -EAGAIN || error == -ETIMEDOUT) ? -ETIMEDOUT : error;
-}
+		if (!error && cyapa->state > CYAPA_STATE_BL_BUSY)
+			return 0;
 
-static int cyapa_bl_deactivate(struct cyapa *cyapa)
-{
-	int error;
-
-	error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_deactivate),
-					  bl_deactivate);
-	if (error)
-		return error;
-
-	/* wait for bootloader to switch to idle state; should take < 100ms */
-	msleep(100);
-	error = cyapa_poll_state(cyapa, 500);
-	if (error)
-		return error;
-	if (cyapa->state != CYAPA_STATE_BL_IDLE)
-		return -EAGAIN;
-	return 0;
-}
-
-/*
- * Exit bootloader
- *
- * Send bl_exit command, then wait 50 - 100 ms to let device transition to
- * operational mode.  If this is the first time the device's firmware is
- * running, it can take up to 2 seconds to calibrate its sensors.  So, poll
- * the device's new state for up to 2 seconds.
- *
- * Returns:
- *   -EIO    failure while reading from device
- *   -EAGAIN device is stuck in bootloader, b/c it has invalid firmware
- *   0       device is supported and in operational mode
- */
-static int cyapa_bl_exit(struct cyapa *cyapa)
-{
-	int error;
-
-	error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_exit), bl_exit);
-	if (error)
-		return error;
-
-	/*
-	 * Wait for bootloader to exit, and operation mode to start.
-	 * Normally, this takes at least 50 ms.
-	 */
-	usleep_range(50000, 100000);
-	/*
-	 * In addition, when a device boots for the first time after being
-	 * updated to new firmware, it must first calibrate its sensors, which
-	 * can take up to an additional 2 seconds.
-	 */
-	error = cyapa_poll_state(cyapa, 2000);
-	if (error < 0)
-		return error;
-	if (cyapa->state != CYAPA_STATE_OP)
-		return -EAGAIN;
-
-	return 0;
-}
-
-/*
- * Set device power mode
- *
- */
-static int cyapa_set_power_mode(struct cyapa *cyapa, u8 power_mode)
-{
-	struct device *dev = &cyapa->client->dev;
-	int ret;
-	u8 power;
-
-	if (cyapa->state != CYAPA_STATE_OP)
-		return 0;
-
-	ret = cyapa_read_byte(cyapa, CYAPA_CMD_POWER_MODE);
-	if (ret < 0)
-		return ret;
-
-	power = ret & ~PWR_MODE_MASK;
-	power |= power_mode & PWR_MODE_MASK;
-	ret = cyapa_write_byte(cyapa, CYAPA_CMD_POWER_MODE, power);
-	if (ret < 0) {
-		dev_err(dev, "failed to set power_mode 0x%02x err = %d\n",
-			power_mode, ret);
-		return ret;
-	}
-
-	return 0;
-}
-
-static int cyapa_get_query_data(struct cyapa *cyapa)
-{
-	u8 query_data[QUERY_DATA_SIZE];
-	int ret;
-
-	if (cyapa->state != CYAPA_STATE_OP)
-		return -EBUSY;
-
-	ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_QUERY, query_data);
-	if (ret < 0)
-		return ret;
-	if (ret != QUERY_DATA_SIZE)
-		return -EIO;
-
-	memcpy(&cyapa->product_id[0], &query_data[0], 5);
-	cyapa->product_id[5] = '-';
-	memcpy(&cyapa->product_id[6], &query_data[5], 6);
-	cyapa->product_id[12] = '-';
-	memcpy(&cyapa->product_id[13], &query_data[11], 2);
-	cyapa->product_id[15] = '\0';
-
-	cyapa->btn_capability = query_data[19] & CAPABILITY_BTN_MASK;
-
-	cyapa->gen = query_data[20] & 0x0f;
-
-	cyapa->max_abs_x = ((query_data[21] & 0xf0) << 4) | query_data[22];
-	cyapa->max_abs_y = ((query_data[21] & 0x0f) << 8) | query_data[23];
-
-	cyapa->physical_size_x =
-		((query_data[24] & 0xf0) << 4) | query_data[25];
-	cyapa->physical_size_y =
-		((query_data[24] & 0x0f) << 8) | query_data[26];
+		msleep(100);
+	} while (tries--);
 
-	return 0;
+	return (error == -EAGAIN || error == -ETIMEDOUT) ? -ETIMEDOUT : error;
 }
 
 /*
@@ -628,8 +254,10 @@ static int cyapa_get_query_data(struct cyapa *cyapa)
  * firmware supported by this driver.
  *
  * Returns:
+ *   -ENODEV no device
  *   -EBUSY  no device or in bootloader
  *   -EIO    failure while reading from device
+ *   -ETIMEDOUT timeout failure for bus idle or bus no response
  *   -EAGAIN device is still in bootloader
  *           if ->state = CYAPA_STATE_BL_IDLE, device has invalid firmware
  *   -EINVAL device is in operational mode, but not supported by this driver
@@ -637,122 +265,53 @@ static int cyapa_get_query_data(struct cyapa *cyapa)
  */
 static int cyapa_check_is_operational(struct cyapa *cyapa)
 {
-	struct device *dev = &cyapa->client->dev;
-	static const char unique_str[] = "CYTRA";
 	int error;
 
-	error = cyapa_poll_state(cyapa, 2000);
+	error = cyapa_poll_state(cyapa, 4000);
 	if (error)
 		return error;
-	switch (cyapa->state) {
-	case CYAPA_STATE_BL_ACTIVE:
-		error = cyapa_bl_deactivate(cyapa);
-		if (error)
-			return error;
-
-	/* Fallthrough state */
-	case CYAPA_STATE_BL_IDLE:
-		error = cyapa_bl_exit(cyapa);
-		if (error)
-			return error;
-
-	/* Fallthrough state */
-	case CYAPA_STATE_OP:
-		error = cyapa_get_query_data(cyapa);
-		if (error)
-			return error;
-
-		/* only support firmware protocol gen3 */
-		if (cyapa->gen != CYAPA_GEN3) {
-			dev_err(dev, "unsupported protocol version (%d)",
-				cyapa->gen);
-			return -EINVAL;
-		}
-
-		/* only support product ID starting with CYTRA */
-		if (memcmp(cyapa->product_id, unique_str,
-			   sizeof(unique_str) - 1) != 0) {
-			dev_err(dev, "unsupported product ID (%s)\n",
-				cyapa->product_id);
-			return -EINVAL;
-		}
-		return 0;
 
+	switch (cyapa->gen) {
+	case CYAPA_GEN3:
+		cyapa->ops = &cyapa_gen3_ops;
+		break;
 	default:
-		return -EIO;
+		return -ENODEV;
 	}
-	return 0;
+
+	error = cyapa->ops->operational_check(cyapa);
+	if (!error && cyapa_is_operational_mode(cyapa))
+		cyapa->operational = true;
+	else
+		cyapa->operational = false;
+
+	return error;
 }
 
-static irqreturn_t cyapa_irq(int irq, void *dev_id)
+
+/*
+ * Returns 0 on device detected, negative errno on no device detected.
+ * And when the device is detected and opertaional, it will be reset to
+ * full power active mode automatically.
+ */
+static int cyapa_detect(struct cyapa *cyapa)
 {
-	struct cyapa *cyapa = dev_id;
 	struct device *dev = &cyapa->client->dev;
-	struct input_dev *input = cyapa->input;
-	struct cyapa_reg_data data;
-	int i;
-	int ret;
-	int num_fingers;
-
-	if (device_may_wakeup(dev))
-		pm_wakeup_event(dev, 0);
-
-	ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_DATA, (u8 *)&data);
-	if (ret != sizeof(data))
-		goto out;
+	int error;
 
-	if ((data.device_status & OP_STATUS_SRC) != OP_STATUS_SRC ||
-	    (data.device_status & OP_STATUS_DEV) != CYAPA_DEV_NORMAL ||
-	    (data.finger_btn & OP_DATA_VALID) != OP_DATA_VALID) {
-		goto out;
-	}
+	error = cyapa_check_is_operational(cyapa);
+	if (error) {
+		if (error != -ETIMEDOUT && error != -ENODEV &&
+			cyapa_is_bootloader_mode(cyapa)) {
+			dev_warn(dev, "device detected but not operational\n");
+			return 0;
+		}
 
-	num_fingers = (data.finger_btn >> 4) & 0x0f;
-	for (i = 0; i < num_fingers; i++) {
-		const struct cyapa_touch *touch = &data.touches[i];
-		/* Note: touch->id range is 1 to 15; slots are 0 to 14. */
-		int slot = touch->id - 1;
-
-		input_mt_slot(input, slot);
-		input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
-		input_report_abs(input, ABS_MT_POSITION_X,
-				 ((touch->xy_hi & 0xf0) << 4) | touch->x_lo);
-		input_report_abs(input, ABS_MT_POSITION_Y,
-				 ((touch->xy_hi & 0x0f) << 8) | touch->y_lo);
-		input_report_abs(input, ABS_MT_PRESSURE, touch->pressure);
+		dev_err(dev, "no device detected: %d\n", error);
+		return error;
 	}
 
-	input_mt_sync_frame(input);
-
-	if (cyapa->btn_capability & CAPABILITY_LEFT_BTN_MASK)
-		input_report_key(input, BTN_LEFT,
-				 data.finger_btn & OP_DATA_LEFT_BTN);
-
-	if (cyapa->btn_capability & CAPABILITY_MIDDLE_BTN_MASK)
-		input_report_key(input, BTN_MIDDLE,
-				 data.finger_btn & OP_DATA_MIDDLE_BTN);
-
-	if (cyapa->btn_capability & CAPABILITY_RIGHT_BTN_MASK)
-		input_report_key(input, BTN_RIGHT,
-				 data.finger_btn & OP_DATA_RIGHT_BTN);
-
-	input_sync(input);
-
-out:
-	return IRQ_HANDLED;
-}
-
-static u8 cyapa_check_adapter_functionality(struct i2c_client *client)
-{
-	u8 ret = CYAPA_ADAPTER_FUNC_NONE;
-
-	if (i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
-		ret |= CYAPA_ADAPTER_FUNC_I2C;
-	if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA |
-				     I2C_FUNC_SMBUS_BLOCK_DATA |
-				     I2C_FUNC_SMBUS_I2C_BLOCK))
-		ret |= CYAPA_ADAPTER_FUNC_SMBUS;
-	return ret;
+	return 0;
 }
 
 static int cyapa_open(struct input_dev *input)
@@ -761,22 +320,49 @@ static int cyapa_open(struct input_dev *input)
 	struct i2c_client *client = cyapa->client;
 	int error;
 
-	error = cyapa_set_power_mode(cyapa, PWR_MODE_FULL_ACTIVE);
-	if (error) {
-		dev_err(&client->dev, "set active power failed: %d\n", error);
+	error = mutex_lock_interruptible(&cyapa->state_sync_lock);
+	if (error)
 		return error;
+
+	if (cyapa->operational) {
+		/*
+		 * though failed to set active power mode,
+		 * but still may be able to work in lower scan rate
+		 * when in operational mode.
+		 */
+		error = cyapa->ops->set_power_mode(cyapa,
+				PWR_MODE_FULL_ACTIVE, 0);
+		if (error) {
+			dev_warn(&client->dev,
+				"set active power failed: %d\n", error);
+			goto out;
+		}
+	} else {
+		error = cyapa_reinitialize(cyapa);
+		if (error || !cyapa->operational) {
+			error = error ? error : -EAGAIN;
+			goto out;
+		}
 	}
 
 	enable_irq(client->irq);
-	return 0;
+out:
+	mutex_unlock(&cyapa->state_sync_lock);
+	return error;
 }
 
 static void cyapa_close(struct input_dev *input)
 {
 	struct cyapa *cyapa = input_get_drvdata(input);
+	struct i2c_client *client = cyapa->client;
+
+	mutex_lock(&cyapa->state_sync_lock);
 
-	disable_irq(cyapa->client->irq);
-	cyapa_set_power_mode(cyapa, PWR_MODE_OFF);
+	disable_irq(client->irq);
+	if (cyapa->operational)
+		cyapa->ops->set_power_mode(cyapa, PWR_MODE_OFF, 0);
+
+	mutex_unlock(&cyapa->state_sync_lock);
 }
 
 static int cyapa_create_input_dev(struct cyapa *cyapa)
@@ -813,7 +399,28 @@ static int cyapa_create_input_dev(struct cyapa *cyapa)
 			     0);
 	input_set_abs_params(input, ABS_MT_POSITION_Y, 0, cyapa->max_abs_y, 0,
 			     0);
-	input_set_abs_params(input, ABS_MT_PRESSURE, 0, 255, 0, 0);
+	input_set_abs_params(input, ABS_MT_PRESSURE, 0, cyapa->max_z, 0, 0);
+	if (cyapa->gen > CYAPA_GEN3) {
+		input_set_abs_params(input, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
+		input_set_abs_params(input, ABS_MT_TOUCH_MINOR, 0, 255, 0, 0);
+		/*
+		 * Orientation is the angle between the vertical axis and
+		 * the major axis of the contact ellipse.
+		 * The range is -127 to 127.
+		 * the positive direction is clockwise form the vertical axis.
+		 * If the ellipse of contact degenerates into a circle,
+		 * orientation is reported as 0.
+		 *
+		 * Also, for Gen5 trackpad the accurate of this orientation
+		 * value is value + (-30 ~ 30).
+		 */
+		input_set_abs_params(input, ABS_MT_ORIENTATION,
+				-127, 127, 0, 0);
+	}
+	if (cyapa->gen >= CYAPA_GEN5) {
+		input_set_abs_params(input, ABS_MT_WIDTH_MAJOR, 0, 255, 0, 0);
+		input_set_abs_params(input, ABS_MT_WIDTH_MINOR, 0, 255, 0, 0);
+	}
 
 	input_abs_set_res(input, ABS_MT_POSITION_X,
 			  cyapa->max_abs_x / cyapa->physical_size_x);
@@ -838,16 +445,159 @@ static int cyapa_create_input_dev(struct cyapa *cyapa)
 		return error;
 	}
 
+	/* Register the device in input subsystem */
+	error = input_register_device(input);
+	if (error) {
+		dev_err(dev, "failed to register input device: %d\n", error);
+		return error;
+	}
+
 	cyapa->input = input;
 	return 0;
 }
 
+/*
+ * cyapa_sleep_time_to_pwr_cmd and cyapa_pwr_cmd_to_sleep_time
+ *
+ * These are helper functions that convert to and from integer idle
+ * times and register settings to write to the PowerMode register.
+ * The trackpad supports between 20ms to 1000ms scan intervals.
+ * The time will be increased in increments of 10ms from 20ms to 100ms.
+ * From 100ms to 1000ms, time will be increased in increments of 20ms.
+ *
+ * When Idle_Time < 100, the format to convert Idle_Time to Idle_Command is:
+ *   Idle_Command = Idle Time / 10;
+ * When Idle_Time >= 100, the format to convert Idle_Time to Idle_Command is:
+ *   Idle_Command = Idle Time / 20 + 5;
+ */
+u8 cyapa_sleep_time_to_pwr_cmd(u16 sleep_time)
+{
+	u16 encoded_time;
+
+	sleep_time = clamp_val(sleep_time, 20, 1000);
+	encoded_time = sleep_time < 100 ? sleep_time / 10 : sleep_time / 20 + 5;
+	return (encoded_time << 2) & PWR_MODE_MASK;
+}
+
+u16 cyapa_pwr_cmd_to_sleep_time(u8 pwr_mode)
+{
+	u8 encoded_time = pwr_mode >> 2;
+
+	return (encoded_time < 10) ? encoded_time * 10
+				   : (encoded_time - 5) * 20;
+}
+
+/* 0 on driver initialize and detected successfully, negative on failure. */
+static int cyapa_initialize(struct cyapa *cyapa)
+{
+	int error = 0;
+
+	cyapa->state = CYAPA_STATE_NO_DEVICE;
+	cyapa->gen = CYAPA_GEN_UNKNOWN;
+	mutex_init(&cyapa->state_sync_lock);
+
+	/*
+	 * Set to hard code default, they will be updated with trackpad set
+	 * default values after probe and initialized.
+	 */
+	cyapa->suspend_power_mode = PWR_MODE_SLEEP;
+	cyapa->suspend_sleep_time =
+		cyapa_pwr_cmd_to_sleep_time(cyapa->suspend_power_mode);
+
+	/* ops.initialize() is aimed to prepare for module communications. */
+	error = cyapa_gen3_ops.initialize(cyapa);
+	if (error)
+		return error;
+
+	error = cyapa_detect(cyapa);
+	if (error)
+		return error;
+
+	/* Power down the device until we need it. */
+	if (cyapa->operational)
+		cyapa->ops->set_power_mode(cyapa, PWR_MODE_OFF, 0);
+
+	return 0;
+}
+
+static int cyapa_reinitialize(struct cyapa *cyapa)
+{
+	struct device *dev = &cyapa->client->dev;
+	struct input_dev *input = cyapa->input;
+	int error;
+
+	/* Avoid command failures when TP was in OFF state. */
+	if (cyapa->operational)
+		cyapa->ops->set_power_mode(cyapa, PWR_MODE_FULL_ACTIVE, 0);
+
+	error = cyapa_detect(cyapa);
+	if (error)
+		goto out;
+
+	if (!input && cyapa->operational) {
+		error = cyapa_create_input_dev(cyapa);
+		if (error) {
+			dev_err(dev, "create input_dev instance failed: %d\n",
+					error);
+			goto out;
+		}
+	}
+
+out:
+	if (!input || !input->users) {
+		/* Reset to power OFF state to save power when no user open. */
+		if (cyapa->operational)
+			cyapa->ops->set_power_mode(cyapa, PWR_MODE_OFF, 0);
+	}
+
+	return error;
+}
+
+static irqreturn_t cyapa_irq(int irq, void *dev_id)
+{
+	struct cyapa *cyapa = dev_id;
+	struct device *dev = &cyapa->client->dev;
+
+	if (device_may_wakeup(dev))
+		pm_wakeup_event(dev, 0);
+
+	/* Interrupt event maybe cuased by host command to trackpad device. */
+	if (cyapa->ops->irq_cmd_handler(cyapa)) {
+		/*
+		 * Interrupt event maybe from trackpad device input reporting.
+		 */
+		if (!cyapa->input) {
+			/*
+			 * Still in probling or in firware image
+			 * udpating or reading.
+			 */
+			cyapa->ops->sort_empty_output_data(cyapa,
+					NULL, NULL, NULL);
+			goto out;
+		}
+
+		if (!cyapa->operational || cyapa->ops->irq_handler(cyapa)) {
+			if (!mutex_trylock(&cyapa->state_sync_lock)) {
+				cyapa->ops->sort_empty_output_data(cyapa,
+					NULL, NULL, NULL);
+				goto out;
+			}
+			cyapa_reinitialize(cyapa);
+			mutex_unlock(&cyapa->state_sync_lock);
+		}
+	}
+
+out:
+	return IRQ_HANDLED;
+}
+
 static int cyapa_probe(struct i2c_client *client,
 		       const struct i2c_device_id *dev_id)
 {
 	struct device *dev = &client->dev;
 	struct cyapa *cyapa;
 	u8 adapter_func;
+	union i2c_smbus_data dummy;
 	int error;
 
 	adapter_func = cyapa_check_adapter_functionality(client);
@@ -856,39 +606,30 @@ static int cyapa_probe(struct i2c_client *client,
 		return -EIO;
 	}
 
+	/* Make sure there is something at this address */
+	if (i2c_smbus_xfer(client->adapter, client->addr, 0,
+			I2C_SMBUS_READ, 0, I2C_SMBUS_BYTE, &dummy) < 0)
+		return -ENODEV;
+
 	cyapa = devm_kzalloc(dev, sizeof(struct cyapa), GFP_KERNEL);
 	if (!cyapa)
 		return -ENOMEM;
 
-	cyapa->gen = CYAPA_GEN3;
-	cyapa->client = client;
-	i2c_set_clientdata(client, cyapa);
-	sprintf(cyapa->phys, "i2c-%d-%04x/input0", client->adapter->nr,
-		client->addr);
-
 	/* i2c isn't supported, use smbus */
 	if (adapter_func == CYAPA_ADAPTER_FUNC_SMBUS)
 		cyapa->smbus = true;
 
-	cyapa->state = CYAPA_STATE_NO_DEVICE;
-
-	error = cyapa_check_is_operational(cyapa);
-	if (error) {
-		dev_err(dev, "device not operational, %d\n", error);
-		return error;
-	}
+	cyapa->client = client;
+	i2c_set_clientdata(client, cyapa);
+	sprintf(cyapa->phys, "i2c-%d-%04x/input0", client->adapter->nr,
+		client->addr);
 
-	/* Power down the device until we need it */
-	error = cyapa_set_power_mode(cyapa, PWR_MODE_OFF);
+	error = cyapa_initialize(cyapa);
 	if (error) {
-		dev_err(dev, "failed to quiesce the device: %d\n", error);
+		dev_err(dev, "failed to detect and initialize tp device.\n");
 		return error;
 	}
 
-	error = cyapa_create_input_dev(cyapa);
-	if (error)
-		return error;
-
 	error = devm_request_threaded_irq(dev, client->irq,
 					  NULL, cyapa_irq,
 					  IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
@@ -901,11 +642,18 @@ static int cyapa_probe(struct i2c_client *client,
 	/* Disable IRQ until the device is opened */
 	disable_irq(client->irq);
 
-	/* Register the device in input subsystem */
-	error = input_register_device(cyapa->input);
-	if (error) {
-		dev_err(dev, "failed to register input device: %d\n", error);
-		return error;
+	/*
+	 * Register the device in the input subsystem when it's operational.
+	 * Otherwise, keep in this driver, so it can be be recovered or updated
+	 * through the sysfs mode and update_fw interfaces by user or apps.
+	 */
+	if (cyapa->operational) {
+		error = cyapa_create_input_dev(cyapa);
+		if (error) {
+			dev_err(dev, "create input_dev instance failed: %d\n",
+					error);
+			return error;
+		}
 	}
 
 	return 0;
@@ -915,11 +663,10 @@ static int __maybe_unused cyapa_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct cyapa *cyapa = i2c_get_clientdata(client);
-	struct input_dev *input = cyapa->input;
 	u8 power_mode;
 	int error;
 
-	error = mutex_lock_interruptible(&input->mutex);
+	error = mutex_lock_interruptible(&cyapa->state_sync_lock);
 	if (error)
 		return error;
 
@@ -929,18 +676,20 @@ static int __maybe_unused cyapa_suspend(struct device *dev)
 	 * Set trackpad device to idle mode if wakeup is allowed,
 	 * otherwise turn off.
 	 */
-	power_mode = device_may_wakeup(dev) ? PWR_MODE_IDLE
-					    : PWR_MODE_OFF;
-	error = cyapa_set_power_mode(cyapa, power_mode);
-	if (error)
-		dev_err(dev, "resume: set power mode to %d failed: %d\n",
-			 power_mode, error);
+	if (cyapa->operational) {
+		power_mode = device_may_wakeup(dev) ? cyapa->suspend_power_mode
+						    : PWR_MODE_OFF;
+		error = cyapa->ops->set_power_mode(cyapa, power_mode,
+				cyapa->suspend_sleep_time);
+		if (error)
+			dev_err(dev, "suspend set power mode failed: %d\n",
+					error);
+	}
 
 	if (device_may_wakeup(dev))
 		cyapa->irq_wake = (enable_irq_wake(client->irq) == 0);
 
-	mutex_unlock(&input->mutex);
-
+	mutex_unlock(&cyapa->state_sync_lock);
 	return 0;
 }
 
@@ -948,25 +697,22 @@ static int __maybe_unused cyapa_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct cyapa *cyapa = i2c_get_clientdata(client);
-	struct input_dev *input = cyapa->input;
-	u8 power_mode;
 	int error;
 
-	mutex_lock(&input->mutex);
+	mutex_lock(&cyapa->state_sync_lock);
 
-	if (device_may_wakeup(dev) && cyapa->irq_wake)
+	if (device_may_wakeup(dev) && cyapa->irq_wake) {
 		disable_irq_wake(client->irq);
+		cyapa->irq_wake = false;
+	}
 
-	power_mode = input->users ? PWR_MODE_FULL_ACTIVE : PWR_MODE_OFF;
-	error = cyapa_set_power_mode(cyapa, PWR_MODE_FULL_ACTIVE);
+	error = cyapa_reinitialize(cyapa);
 	if (error)
-		dev_warn(dev, "resume: set power mode to %d failed: %d\n",
-			 power_mode, error);
+		dev_warn(dev, "failed to reinitialize TP device: %d\n", error);
 
 	enable_irq(client->irq);
 
-	mutex_unlock(&input->mutex);
-
+	mutex_unlock(&cyapa->state_sync_lock);
 	return 0;
 }
 
diff --git a/drivers/input/mouse/cyapa.h b/drivers/input/mouse/cyapa.h
new file mode 100644
index 0000000..aab19b7
--- /dev/null
+++ b/drivers/input/mouse/cyapa.h
@@ -0,0 +1,296 @@
+/*
+ * Cypress APA trackpad with I2C interface
+ *
+ * Author: Dudley Du <dudl@cypress.com>
+ *
+ * Copyright (C) 2014 Cypress Semiconductor, Inc.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file COPYING in the main directory of this archive for
+ * more details.
+ */
+
+#ifndef _CYAPA_H
+#define _CYAPA_H
+
+#include <linux/firmware.h>
+
+/* APA trackpad firmware generation number. */
+#define CYAPA_GEN_UNKNOWN   0x00   /* unknown protocol. */
+#define CYAPA_GEN3   0x03   /* support MT-protocol B with tracking ID. */
+#define CYAPA_GEN5   0x05   /* support TrueTouch GEN5 trackpad device. */
+
+#define CYAPA_NAME   "Cypress APA Trackpad (cyapa)"
+
+/*
+ * Macros for SMBus communication
+ */
+#define SMBUS_READ   0x01
+#define SMBUS_WRITE 0x00
+#define SMBUS_ENCODE_IDX(cmd, idx) ((cmd) | (((idx) & 0x03) << 1))
+#define SMBUS_ENCODE_RW(cmd, rw) ((cmd) | ((rw) & 0x01))
+#define SMBUS_BYTE_BLOCK_CMD_MASK 0x80
+#define SMBUS_GROUP_BLOCK_CMD_MASK 0x40
+
+/* Commands for read/write registers of Cypress trackpad */
+#define CYAPA_CMD_SOFT_RESET       0x00
+#define CYAPA_CMD_POWER_MODE       0x01
+#define CYAPA_CMD_DEV_STATUS       0x02
+#define CYAPA_CMD_GROUP_DATA       0x03
+#define CYAPA_CMD_GROUP_CMD        0x04
+#define CYAPA_CMD_GROUP_QUERY      0x05
+#define CYAPA_CMD_BL_STATUS        0x06
+#define CYAPA_CMD_BL_HEAD          0x07
+#define CYAPA_CMD_BL_CMD           0x08
+#define CYAPA_CMD_BL_DATA          0x09
+#define CYAPA_CMD_BL_ALL           0x0a
+#define CYAPA_CMD_BLK_PRODUCT_ID   0x0b
+#define CYAPA_CMD_BLK_HEAD         0x0c
+#define CYAPA_CMD_MAX_BASELINE     0x0d
+#define CYAPA_CMD_MIN_BASELINE     0x0e
+
+#define BL_HEAD_OFFSET 0x00
+#define BL_DATA_OFFSET 0x10
+
+#define BL_STATUS_SIZE  3  /* Length of gen3 bootloader status registers */
+#define CYAPA_REG_MAP_SIZE  256
+
+/*
+ * Gen3 Operational Device Status Register
+ *
+ * bit 7: Valid interrupt source
+ * bit 6 - 4: Reserved
+ * bit 3 - 2: Power status
+ * bit 1 - 0: Device status
+ */
+#define REG_OP_STATUS     0x00
+#define OP_STATUS_SRC     0x80
+#define OP_STATUS_POWER   0x0c
+#define OP_STATUS_DEV     0x03
+#define OP_STATUS_MASK (OP_STATUS_SRC | OP_STATUS_POWER | OP_STATUS_DEV)
+
+/*
+ * Operational Finger Count/Button Flags Register
+ *
+ * bit 7 - 4: Number of touched finger
+ * bit 3: Valid data
+ * bit 2: Middle Physical Button
+ * bit 1: Right Physical Button
+ * bit 0: Left physical Button
+ */
+#define REG_OP_DATA1       0x01
+#define OP_DATA_VALID      0x08
+#define OP_DATA_MIDDLE_BTN 0x04
+#define OP_DATA_RIGHT_BTN  0x02
+#define OP_DATA_LEFT_BTN   0x01
+#define OP_DATA_BTN_MASK (OP_DATA_MIDDLE_BTN | OP_DATA_RIGHT_BTN | \
+			  OP_DATA_LEFT_BTN)
+
+/*
+ * Write-only command file register used to issue commands and
+ * parameters to the bootloader.
+ * The default value read from it is always 0x00.
+ */
+#define REG_BL_FILE	0x00
+#define BL_FILE		0x00
+
+/*
+ * Bootloader Status Register
+ *
+ * bit 7: Busy
+ * bit 6 - 5: Reserved
+ * bit 4: Bootloader running
+ * bit 3 - 2: Reserved
+ * bit 1: Watchdog Reset
+ * bit 0: Checksum valid
+ */
+#define REG_BL_STATUS        0x01
+#define BL_STATUS_REV_6_5    0x60
+#define BL_STATUS_BUSY       0x80
+#define BL_STATUS_RUNNING    0x10
+#define BL_STATUS_REV_3_2    0x0c
+#define BL_STATUS_WATCHDOG   0x02
+#define BL_STATUS_CSUM_VALID 0x01
+#define BL_STATUS_REV_MASK (BL_STATUS_WATCHDOG | BL_STATUS_REV_3_2 | \
+			    BL_STATUS_REV_6_5)
+
+/*
+ * Bootloader Error Register
+ *
+ * bit 7: Invalid
+ * bit 6: Invalid security key
+ * bit 5: Bootloading
+ * bit 4: Command checksum
+ * bit 3: Flash protection error
+ * bit 2: Flash checksum error
+ * bit 1 - 0: Reserved
+ */
+#define REG_BL_ERROR         0x02
+#define BL_ERROR_INVALID     0x80
+#define BL_ERROR_INVALID_KEY 0x40
+#define BL_ERROR_BOOTLOADING 0x20
+#define BL_ERROR_CMD_CSUM    0x10
+#define BL_ERROR_FLASH_PROT  0x08
+#define BL_ERROR_FLASH_CSUM  0x04
+#define BL_ERROR_RESERVED    0x03
+#define BL_ERROR_NO_ERR_IDLE    0x00
+#define BL_ERROR_NO_ERR_ACTIVE  (BL_ERROR_BOOTLOADING)
+
+#define CAPABILITY_BTN_SHIFT            3
+#define CAPABILITY_LEFT_BTN_MASK	(0x01 << 3)
+#define CAPABILITY_RIGHT_BTN_MASK	(0x01 << 4)
+#define CAPABILITY_MIDDLE_BTN_MASK	(0x01 << 5)
+#define CAPABILITY_BTN_MASK  (CAPABILITY_LEFT_BTN_MASK | \
+			      CAPABILITY_RIGHT_BTN_MASK | \
+			      CAPABILITY_MIDDLE_BTN_MASK)
+
+#define PWR_MODE_MASK   0xfc
+#define PWR_MODE_FULL_ACTIVE (0x3f << 2)
+#define PWR_MODE_IDLE        (0x03 << 2) /* Default rt suspend scanrate: 30ms */
+#define PWR_MODE_SLEEP       (0x05 << 2) /* Default suspend scanrate: 50ms */
+#define PWR_MODE_BTN_ONLY    (0x01 << 2)
+#define PWR_MODE_OFF         (0x00 << 2)
+
+#define PWR_STATUS_MASK      0x0c
+#define PWR_STATUS_ACTIVE    (0x03 << 2)
+#define PWR_STATUS_IDLE      (0x02 << 2)
+#define PWR_STATUS_BTN_ONLY  (0x01 << 2)
+#define PWR_STATUS_OFF       (0x00 << 2)
+
+#define AUTOSUSPEND_DELAY   2000 /* unit : ms */
+
+#define UNINIT_SLEEP_TIME 0xFFFF
+#define UNINIT_PWR_MODE   0xFF
+
+#define BTN_ONLY_MODE_NAME   "buttononly"
+#define OFF_MODE_NAME        "off"
+
+/* The touch.id is used as the MT slot id, thus max MT slot is 15 */
+#define CYAPA_MAX_MT_SLOTS  15
+
+struct cyapa;
+
+typedef bool (*cb_sort)(struct cyapa *, u8 *, int);
+
+struct cyapa_dev_ops {
+	int (*check_fw)(struct cyapa *, const struct firmware *);
+	int (*bl_enter)(struct cyapa *);
+	int (*bl_activate)(struct cyapa *);
+	int (*bl_initiate)(struct cyapa *, const struct firmware *);
+	int (*update_fw)(struct cyapa *, const struct firmware *);
+	int (*bl_deactivate)(struct cyapa *);
+
+	ssize_t (*show_baseline)(struct device *,
+			struct device_attribute *, char *);
+	ssize_t (*calibrate_store)(struct device *,
+			struct device_attribute *, const char *, size_t);
+
+	int (*initialize)(struct cyapa *cyapa);
+
+	int (*state_parse)(struct cyapa *cyapa, u8 *reg_status, int len);
+	int (*operational_check)(struct cyapa *cyapa);
+
+	int (*irq_handler)(struct cyapa *);
+	bool (*irq_cmd_handler)(struct cyapa *);
+	int (*sort_empty_output_data)(struct cyapa *,
+			u8 *, int *, cb_sort);
+
+	int (*set_power_mode)(struct cyapa *, u8, u16);
+};
+
+struct cyapa_gen5_cmd_states {
+	struct mutex cmd_lock;
+	struct completion cmd_ready;
+	atomic_t cmd_issued;
+	u8 in_progress_cmd;
+	bool is_irq_mode;
+
+	cb_sort resp_sort_func;
+	u8 *resp_data;
+	int *resp_len;
+
+	u8 irq_cmd_buf[CYAPA_REG_MAP_SIZE];
+	u8 empty_buf[CYAPA_REG_MAP_SIZE];
+};
+
+union cyapa_cmd_states {
+	struct cyapa_gen5_cmd_states gen5;
+};
+
+enum cyapa_state {
+	CYAPA_STATE_NO_DEVICE,
+	CYAPA_STATE_BL_BUSY,
+	CYAPA_STATE_BL_IDLE,
+	CYAPA_STATE_BL_ACTIVE,
+	CYAPA_STATE_OP,
+	CYAPA_STATE_GEN5_BL,
+	CYAPA_STATE_GEN5_APP,
+};
+
+/* The main device structure */
+struct cyapa {
+	enum cyapa_state state;
+	u8 status[BL_STATUS_SIZE];
+	bool operational; /* true: ready for data reporting; false: not. */
+
+	struct i2c_client *client;
+	struct input_dev *input;
+	char phys[32];	/* Device physical location */
+	bool irq_wake;  /* Irq wake is enabled */
+	bool smbus;
+
+	/* power mode settings */
+	u8 suspend_power_mode;
+	u16 suspend_sleep_time;
+	u8 dev_pwr_mode;
+	u16 dev_sleep_time;
+
+	/* Read from query data region. */
+	char product_id[16];
+	u8 fw_maj_ver;  /* Firmware major version. */
+	u8 fw_min_ver;  /* Firmware minor version. */
+	u8 btn_capability;
+	u8 gen;
+	int max_abs_x;
+	int max_abs_y;
+	int physical_size_x;
+	int physical_size_y;
+
+	/* Used in ttsp and truetouch based trackpad devices. */
+	u8 x_origin;  /* X Axis Origin: 0 = left side; 1 = rigth side. */
+	u8 y_origin;  /* Y Axis Origin: 0 = top; 1 = bottom. */
+	int electrodes_x;  /* Number of electrodes on the X Axis*/
+	int electrodes_y;  /* Number of electrodes on the Y Axis*/
+	int max_z;
+
+	/*
+	 * Used to synchronize the access or update the device state.
+	 * And since update firmware and read firmware image process will take
+	 * quite long time, maybe more than 10 seconds, so use mutex_lock
+	 * to sync and wait other interface and detecting are done or ready.
+	 */
+	struct mutex state_sync_lock;
+
+	const struct cyapa_dev_ops *ops;
+
+	union cyapa_cmd_states cmd_states;
+};
+
+
+ssize_t cyapa_i2c_reg_read_block(struct cyapa *cyapa, u8 reg, size_t len,
+				u8 *values);
+ssize_t cyapa_smbus_read_block(struct cyapa *cyapa, u8 cmd, size_t len,
+				u8 *values);
+
+ssize_t cyapa_read_block(struct cyapa *cyapa, u8 cmd_idx, u8 *values);
+
+int cyapa_poll_state(struct cyapa *cyapa, unsigned int timeout);
+
+u8 cyapa_sleep_time_to_pwr_cmd(u16 sleep_time);
+u16 cyapa_pwr_cmd_to_sleep_time(u8 pwr_mode);
+
+
+extern const char product_id[];
+extern const struct cyapa_dev_ops cyapa_gen3_ops;
+
+#endif
diff --git a/drivers/input/mouse/cyapa_gen3.c b/drivers/input/mouse/cyapa_gen3.c
new file mode 100644
index 0000000..1b62c7d
--- /dev/null
+++ b/drivers/input/mouse/cyapa_gen3.c
@@ -0,0 +1,807 @@
+/*
+ * Cypress APA trackpad with I2C interface
+ *
+ * Author: Dudley Du <dudl@cypress.com>
+ * Further cleanup and restructuring by:
+ *   Daniel Kurtz <djkurtz@chromium.org>
+ *   Benson Leung <bleung@chromium.org>
+ *
+ * Copyright (C) 2011-2014 Cypress Semiconductor, Inc.
+ * Copyright (C) 2011-2012 Google, Inc.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file COPYING in the main directory of this archive for
+ * more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include "cyapa.h"
+
+
+#define GEN3_MAX_FINGERS 5
+#define GEN3_FINGER_NUM(x) (((x) >> 4) & 0x07)
+
+#define BLK_HEAD_BYTES 32
+
+/* Macro for register map group offset. */
+#define PRODUCT_ID_SIZE  16
+#define QUERY_DATA_SIZE  27
+#define REG_PROTOCOL_GEN_QUERY_OFFSET  20
+
+#define REG_OFFSET_DATA_BASE     0x0000
+#define REG_OFFSET_COMMAND_BASE  0x0028
+#define REG_OFFSET_QUERY_BASE    0x002a
+
+#define CYAPA_OFFSET_SOFT_RESET  REG_OFFSET_COMMAND_BASE
+#define OP_RECALIBRATION_MASK    0x80
+#define OP_REPORT_BASELINE_MASK  0x40
+#define REG_OFFSET_MAX_BASELINE  0x0026
+#define REG_OFFSET_MIN_BASELINE  0x0027
+
+#define REG_OFFSET_POWER_MODE (REG_OFFSET_COMMAND_BASE + 1)
+#define SET_POWER_MODE_DELAY   10000  /* Unit: us */
+#define SET_POWER_MODE_TRIES   5
+
+#define GEN3_BL_CMD_CHECKSUM_SEED 0xff
+#define GEN3_BL_CMD_INITIATE_BL   0x38
+#define GEN3_BL_CMD_WRITE_BLOCK   0x39
+#define GEN3_BL_CMD_VERIFY_BLOCK  0x3a
+#define GEN3_BL_CMD_TERMINATE_BL  0x3b
+#define GEN3_BL_CMD_LAUNCH_APP    0xa5
+
+/*
+ * CYAPA trackpad device states.
+ * Used in register 0x00, bit1-0, DeviceStatus field.
+ * Other values indicate device is in an abnormal state and must be reset.
+ */
+#define CYAPA_DEV_NORMAL  0x03
+#define CYAPA_DEV_BUSY    0x01
+
+#define CYAPA_FW_BLOCK_SIZE	64
+#define CYAPA_FW_READ_SIZE	16
+#define CYAPA_FW_HDR_START	0x0780
+#define CYAPA_FW_HDR_BLOCK_COUNT  2
+#define CYAPA_FW_HDR_BLOCK_START  (CYAPA_FW_HDR_START / CYAPA_FW_BLOCK_SIZE)
+#define CYAPA_FW_HDR_SIZE	  (CYAPA_FW_HDR_BLOCK_COUNT * \
+					CYAPA_FW_BLOCK_SIZE)
+#define CYAPA_FW_DATA_START	0x0800
+#define CYAPA_FW_DATA_BLOCK_COUNT  480
+#define CYAPA_FW_DATA_BLOCK_START  (CYAPA_FW_DATA_START / CYAPA_FW_BLOCK_SIZE)
+#define CYAPA_FW_DATA_SIZE	(CYAPA_FW_DATA_BLOCK_COUNT * \
+				 CYAPA_FW_BLOCK_SIZE)
+#define CYAPA_FW_SIZE		(CYAPA_FW_HDR_SIZE + CYAPA_FW_DATA_SIZE)
+#define CYAPA_CMD_LEN		16
+
+#define GEN3_BL_IDLE_FW_MAJ_VER_OFFSET 0x0b
+#define GEN3_BL_IDLE_FW_MIN_VER_OFFSET (GEN3_BL_IDLE_FW_MAJ_VER_OFFSET + 1)
+
+
+struct cyapa_touch {
+	/*
+	 * high bits or x/y position value
+	 * bit 7 - 4: high 4 bits of x position value
+	 * bit 3 - 0: high 4 bits of y position value
+	 */
+	u8 xy_hi;
+	u8 x_lo;  /* low 8 bits of x position value. */
+	u8 y_lo;  /* low 8 bits of y position value. */
+	u8 pressure;
+	/* id range is 1 - 15.  It is incremented with every new touch. */
+	u8 id;
+} __packed;
+
+struct cyapa_reg_data {
+	/*
+	 * bit 0 - 1: device status
+	 * bit 3 - 2: power mode
+	 * bit 6 - 4: reserved
+	 * bit 7: interrupt valid bit
+	 */
+	u8 device_status;
+	/*
+	 * bit 7 - 4: number of fingers currently touching pad
+	 * bit 3: valid data check bit
+	 * bit 2: middle mechanism button state if exists
+	 * bit 1: right mechanism button state if exists
+	 * bit 0: left mechanism button state if exists
+	 */
+	u8 finger_btn;
+	/* CYAPA reports up to 5 touches per packet. */
+	struct cyapa_touch touches[5];
+} __packed;
+
+static const u8 bl_activate[] = { 0x00, 0xff, 0x38, 0x00, 0x01, 0x02, 0x03,
+		0x04, 0x05, 0x06, 0x07 };
+static const u8 bl_deactivate[] = { 0x00, 0xff, 0x3b, 0x00, 0x01, 0x02, 0x03,
+		0x04, 0x05, 0x06, 0x07 };
+static const u8 bl_exit[] = { 0x00, 0xff, 0xa5, 0x00, 0x01, 0x02, 0x03, 0x04,
+		0x05, 0x06, 0x07 };
+
+
+ /* for byte read/write command */
+#define CMD_RESET      0
+#define CMD_POWER_MODE 1
+#define CMD_DEV_STATUS 2
+#define CMD_REPORT_MAX_BASELINE 3
+#define CMD_REPORT_MIN_BASELINE 4
+#define SMBUS_BYTE_CMD(cmd) (((cmd) & 0x3f) << 1)
+#define CYAPA_SMBUS_RESET         SMBUS_BYTE_CMD(CMD_RESET)
+#define CYAPA_SMBUS_POWER_MODE    SMBUS_BYTE_CMD(CMD_POWER_MODE)
+#define CYAPA_SMBUS_DEV_STATUS    SMBUS_BYTE_CMD(CMD_DEV_STATUS)
+#define CYAPA_SMBUS_MAX_BASELINE  SMBUS_BYTE_CMD(CMD_REPORT_MAX_BASELINE)
+#define CYAPA_SMBUS_MIN_BASELINE  SMBUS_BYTE_CMD(CMD_REPORT_MIN_BASELINE)
+
+ /* for group registers read/write command */
+#define REG_GROUP_DATA 0
+#define REG_GROUP_CMD 2
+#define REG_GROUP_QUERY 3
+#define SMBUS_GROUP_CMD(grp) (0x80 | (((grp) & 0x07) << 3))
+#define CYAPA_SMBUS_GROUP_DATA	 SMBUS_GROUP_CMD(REG_GROUP_DATA)
+#define CYAPA_SMBUS_GROUP_CMD	 SMBUS_GROUP_CMD(REG_GROUP_CMD)
+#define CYAPA_SMBUS_GROUP_QUERY	 SMBUS_GROUP_CMD(REG_GROUP_QUERY)
+
+ /* for register block read/write command */
+#define CMD_BL_STATUS 0
+#define CMD_BL_HEAD 1
+#define CMD_BL_CMD 2
+#define CMD_BL_DATA 3
+#define CMD_BL_ALL 4
+#define CMD_BLK_PRODUCT_ID 5
+#define CMD_BLK_HEAD 6
+#define SMBUS_BLOCK_CMD(cmd) (0xc0 | (((cmd) & 0x1f) << 1))
+
+/* register block read/write command in bootloader mode */
+#define CYAPA_SMBUS_BL_STATUS  SMBUS_BLOCK_CMD(CMD_BL_STATUS)
+#define CYAPA_SMBUS_BL_HEAD    SMBUS_BLOCK_CMD(CMD_BL_HEAD)
+#define CYAPA_SMBUS_BL_CMD     SMBUS_BLOCK_CMD(CMD_BL_CMD)
+#define CYAPA_SMBUS_BL_DATA    SMBUS_BLOCK_CMD(CMD_BL_DATA)
+#define CYAPA_SMBUS_BL_ALL     SMBUS_BLOCK_CMD(CMD_BL_ALL)
+
+/* register block read/write command in operational mode */
+#define CYAPA_SMBUS_BLK_PRODUCT_ID SMBUS_BLOCK_CMD(CMD_BLK_PRODUCT_ID)
+#define CYAPA_SMBUS_BLK_HEAD SMBUS_BLOCK_CMD(CMD_BLK_HEAD)
+
+ /* for byte read/write command */
+#define CMD_RESET 0
+#define CMD_POWER_MODE 1
+#define CMD_DEV_STATUS 2
+#define CMD_REPORT_MAX_BASELINE 3
+#define CMD_REPORT_MIN_BASELINE 4
+#define SMBUS_BYTE_CMD(cmd) (((cmd) & 0x3f) << 1)
+#define CYAPA_SMBUS_RESET         SMBUS_BYTE_CMD(CMD_RESET)
+#define CYAPA_SMBUS_POWER_MODE    SMBUS_BYTE_CMD(CMD_POWER_MODE)
+#define CYAPA_SMBUS_DEV_STATUS    SMBUS_BYTE_CMD(CMD_DEV_STATUS)
+#define CYAPA_SMBUS_MAX_BASELINE  SMBUS_BYTE_CMD(CMD_REPORT_MAX_BASELINE)
+#define CYAPA_SMBUS_MIN_BASELINE  SMBUS_BYTE_CMD(CMD_REPORT_MIN_BASELINE)
+
+ /* for group registers read/write command */
+#define REG_GROUP_DATA  0
+#define REG_GROUP_CMD   2
+#define REG_GROUP_QUERY 3
+#define SMBUS_GROUP_CMD(grp) (0x80 | (((grp) & 0x07) << 3))
+#define CYAPA_SMBUS_GROUP_DATA  SMBUS_GROUP_CMD(REG_GROUP_DATA)
+#define CYAPA_SMBUS_GROUP_CMD   SMBUS_GROUP_CMD(REG_GROUP_CMD)
+#define CYAPA_SMBUS_GROUP_QUERY SMBUS_GROUP_CMD(REG_GROUP_QUERY)
+
+ /* for register block read/write command */
+#define CMD_BL_STATUS		0
+#define CMD_BL_HEAD		1
+#define CMD_BL_CMD		2
+#define CMD_BL_DATA		3
+#define CMD_BL_ALL		4
+#define CMD_BLK_PRODUCT_ID	5
+#define CMD_BLK_HEAD		6
+#define SMBUS_BLOCK_CMD(cmd) (0xc0 | (((cmd) & 0x1f) << 1))
+
+/* register block read/write command in bootloader mode */
+#define CYAPA_SMBUS_BL_STATUS SMBUS_BLOCK_CMD(CMD_BL_STATUS)
+#define CYAPA_SMBUS_BL_HEAD   SMBUS_BLOCK_CMD(CMD_BL_HEAD)
+#define CYAPA_SMBUS_BL_CMD    SMBUS_BLOCK_CMD(CMD_BL_CMD)
+#define CYAPA_SMBUS_BL_DATA   SMBUS_BLOCK_CMD(CMD_BL_DATA)
+#define CYAPA_SMBUS_BL_ALL    SMBUS_BLOCK_CMD(CMD_BL_ALL)
+
+/* register block read/write command in operational mode */
+#define CYAPA_SMBUS_BLK_PRODUCT_ID SMBUS_BLOCK_CMD(CMD_BLK_PRODUCT_ID)
+#define CYAPA_SMBUS_BLK_HEAD       SMBUS_BLOCK_CMD(CMD_BLK_HEAD)
+
+struct cyapa_cmd_len {
+	u8 cmd;
+	u8 len;
+};
+
+/* maps generic CYAPA_CMD_* code to the I2C equivalent */
+static const struct cyapa_cmd_len cyapa_i2c_cmds[] = {
+	{ CYAPA_OFFSET_SOFT_RESET, 1 },		/* CYAPA_CMD_SOFT_RESET */
+	{ REG_OFFSET_COMMAND_BASE + 1, 1 },	/* CYAPA_CMD_POWER_MODE */
+	{ REG_OFFSET_DATA_BASE, 1 },		/* CYAPA_CMD_DEV_STATUS */
+	{ REG_OFFSET_DATA_BASE, sizeof(struct cyapa_reg_data) },
+						/* CYAPA_CMD_GROUP_DATA */
+	{ REG_OFFSET_COMMAND_BASE, 0 },		/* CYAPA_CMD_GROUP_CMD */
+	{ REG_OFFSET_QUERY_BASE, QUERY_DATA_SIZE }, /* CYAPA_CMD_GROUP_QUERY */
+	{ BL_HEAD_OFFSET, 3 },			/* CYAPA_CMD_BL_STATUS */
+	{ BL_HEAD_OFFSET, 16 },			/* CYAPA_CMD_BL_HEAD */
+	{ BL_HEAD_OFFSET, 16 },			/* CYAPA_CMD_BL_CMD */
+	{ BL_DATA_OFFSET, 16 },			/* CYAPA_CMD_BL_DATA */
+	{ BL_HEAD_OFFSET, 32 },			/* CYAPA_CMD_BL_ALL */
+	{ REG_OFFSET_QUERY_BASE, PRODUCT_ID_SIZE },
+						/* CYAPA_CMD_BLK_PRODUCT_ID */
+	{ REG_OFFSET_DATA_BASE, 32 },		/* CYAPA_CMD_BLK_HEAD */
+	{ REG_OFFSET_MAX_BASELINE, 1 },		/* CYAPA_CMD_MAX_BASELINE */
+	{ REG_OFFSET_MIN_BASELINE, 1 },		/* CYAPA_CMD_MIN_BASELINE */
+};
+
+static const struct cyapa_cmd_len cyapa_smbus_cmds[] = {
+	{ CYAPA_SMBUS_RESET, 1 },		/* CYAPA_CMD_SOFT_RESET */
+	{ CYAPA_SMBUS_POWER_MODE, 1 },		/* CYAPA_CMD_POWER_MODE */
+	{ CYAPA_SMBUS_DEV_STATUS, 1 },		/* CYAPA_CMD_DEV_STATUS */
+	{ CYAPA_SMBUS_GROUP_DATA, sizeof(struct cyapa_reg_data) },
+						/* CYAPA_CMD_GROUP_DATA */
+	{ CYAPA_SMBUS_GROUP_CMD, 2 },		/* CYAPA_CMD_GROUP_CMD */
+	{ CYAPA_SMBUS_GROUP_QUERY, QUERY_DATA_SIZE },
+						/* CYAPA_CMD_GROUP_QUERY */
+	{ CYAPA_SMBUS_BL_STATUS, 3 },		/* CYAPA_CMD_BL_STATUS */
+	{ CYAPA_SMBUS_BL_HEAD, 16 },		/* CYAPA_CMD_BL_HEAD */
+	{ CYAPA_SMBUS_BL_CMD, 16 },		/* CYAPA_CMD_BL_CMD */
+	{ CYAPA_SMBUS_BL_DATA, 16 },		/* CYAPA_CMD_BL_DATA */
+	{ CYAPA_SMBUS_BL_ALL, 32 },		/* CYAPA_CMD_BL_ALL */
+	{ CYAPA_SMBUS_BLK_PRODUCT_ID, PRODUCT_ID_SIZE },
+						/* CYAPA_CMD_BLK_PRODUCT_ID */
+	{ CYAPA_SMBUS_BLK_HEAD, 16 },		/* CYAPA_CMD_BLK_HEAD */
+	{ CYAPA_SMBUS_MAX_BASELINE, 1 },	/* CYAPA_CMD_MAX_BASELINE */
+	{ CYAPA_SMBUS_MIN_BASELINE, 1 },	/* CYAPA_CMD_MIN_BASELINE */
+};
+
+
+/*
+ * cyapa_smbus_read_block - perform smbus block read command
+ * @cyapa  - private data structure of the driver
+ * @cmd    - the properly encoded smbus command
+ * @len    - expected length of smbus command result
+ * @values - buffer to store smbus command result
+ *
+ * Returns negative errno, else the number of bytes written.
+ *
+ * Note:
+ * In trackpad device, the memory block allocated for I2C register map
+ * is 256 bytes, so the max read block for I2C bus is 256 bytes.
+ */
+ssize_t cyapa_smbus_read_block(struct cyapa *cyapa, u8 cmd, size_t len,
+				      u8 *values)
+{
+	ssize_t ret;
+	u8 index;
+	u8 smbus_cmd;
+	u8 *buf;
+	struct i2c_client *client = cyapa->client;
+
+	if (!(SMBUS_BYTE_BLOCK_CMD_MASK & cmd))
+		return -EINVAL;
+
+	if (SMBUS_GROUP_BLOCK_CMD_MASK & cmd) {
+		/* read specific block registers command. */
+		smbus_cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ);
+		ret = i2c_smbus_read_block_data(client, smbus_cmd, values);
+		goto out;
+	}
+
+	ret = 0;
+	for (index = 0; index * I2C_SMBUS_BLOCK_MAX < len; index++) {
+		smbus_cmd = SMBUS_ENCODE_IDX(cmd, index);
+		smbus_cmd = SMBUS_ENCODE_RW(smbus_cmd, SMBUS_READ);
+		buf = values + I2C_SMBUS_BLOCK_MAX * index;
+		ret = i2c_smbus_read_block_data(client, smbus_cmd, buf);
+		if (ret < 0)
+			goto out;
+	}
+
+out:
+	return ret > 0 ? len : ret;
+}
+
+static s32 cyapa_read_byte(struct cyapa *cyapa, u8 cmd_idx)
+{
+	u8 cmd;
+
+	if (cyapa->smbus) {
+		cmd = cyapa_smbus_cmds[cmd_idx].cmd;
+		cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ);
+	} else {
+		cmd = cyapa_i2c_cmds[cmd_idx].cmd;
+	}
+	return i2c_smbus_read_byte_data(cyapa->client, cmd);
+}
+
+static s32 cyapa_write_byte(struct cyapa *cyapa, u8 cmd_idx, u8 value)
+{
+	u8 cmd;
+
+	if (cyapa->smbus) {
+		cmd = cyapa_smbus_cmds[cmd_idx].cmd;
+		cmd = SMBUS_ENCODE_RW(cmd, SMBUS_WRITE);
+	} else {
+		cmd = cyapa_i2c_cmds[cmd_idx].cmd;
+	}
+	return i2c_smbus_write_byte_data(cyapa->client, cmd, value);
+}
+
+ssize_t cyapa_i2c_reg_read_block(struct cyapa *cyapa, u8 reg, size_t len,
+					u8 *values)
+{
+	return i2c_smbus_read_i2c_block_data(cyapa->client, reg, len, values);
+}
+
+static ssize_t cyapa_i2c_reg_write_block(struct cyapa *cyapa, u8 reg,
+					 size_t len, const u8 *values)
+{
+	return i2c_smbus_write_i2c_block_data(cyapa->client, reg, len, values);
+}
+
+ssize_t cyapa_read_block(struct cyapa *cyapa, u8 cmd_idx, u8 *values)
+{
+	u8 cmd;
+	size_t len;
+
+	if (cyapa->smbus) {
+		cmd = cyapa_smbus_cmds[cmd_idx].cmd;
+		len = cyapa_smbus_cmds[cmd_idx].len;
+		return cyapa_smbus_read_block(cyapa, cmd, len, values);
+	}
+	cmd = cyapa_i2c_cmds[cmd_idx].cmd;
+	len = cyapa_i2c_cmds[cmd_idx].len;
+	return cyapa_i2c_reg_read_block(cyapa, cmd, len, values);
+}
+
+/*
+ * Determine the Gen3 trackpad device's current operating state.
+ *
+ */
+static int cyapa_gen3_state_parse(struct cyapa *cyapa, u8 *reg_data, int len)
+{
+	cyapa->state = CYAPA_STATE_NO_DEVICE;
+
+	/* Parse based on Gen3 characteristic registers and bits */
+	if (reg_data[REG_BL_FILE] == BL_FILE &&
+		reg_data[REG_BL_ERROR] == BL_ERROR_NO_ERR_IDLE &&
+		(reg_data[REG_BL_STATUS] ==
+			(BL_STATUS_RUNNING | BL_STATUS_CSUM_VALID) ||
+			reg_data[REG_BL_STATUS] == BL_STATUS_RUNNING)) {
+		/*
+		 * Normal state after power on or reset,
+		 * REG_BL_STATUS == 0x11, firmware image checksum is valid.
+		 * REG_BL_STATUS == 0x10, firmware image checksum is invalid.
+		 */
+		cyapa->gen = CYAPA_GEN3;
+		cyapa->state = CYAPA_STATE_BL_IDLE;
+	} else if (reg_data[REG_BL_FILE] == BL_FILE &&
+		(reg_data[REG_BL_STATUS] & BL_STATUS_RUNNING) ==
+			BL_STATUS_RUNNING) {
+		cyapa->gen = CYAPA_GEN3;
+		if (reg_data[REG_BL_STATUS] & BL_STATUS_BUSY) {
+			cyapa->state = CYAPA_STATE_BL_BUSY;
+		} else {
+			if ((reg_data[REG_BL_ERROR] & BL_ERROR_BOOTLOADING) ==
+					BL_ERROR_BOOTLOADING)
+				cyapa->state = CYAPA_STATE_BL_ACTIVE;
+			else
+				cyapa->state = CYAPA_STATE_BL_IDLE;
+		}
+	} else if ((reg_data[REG_OP_STATUS] & OP_STATUS_SRC) &&
+			(reg_data[REG_OP_DATA1] & OP_DATA_VALID)) {
+		/*
+		 * Normal state when running in operational mode,
+		 * may also not in full power state or
+		 * busying in command process.
+		 */
+		if (GEN3_FINGER_NUM(reg_data[REG_OP_DATA1]) <=
+				GEN3_MAX_FINGERS) {
+			/* Finger number data is valid. */
+			cyapa->gen = CYAPA_GEN3;
+			cyapa->state = CYAPA_STATE_OP;
+		}
+	} else if (reg_data[REG_OP_STATUS] == 0x0C &&
+			reg_data[REG_OP_DATA1] == 0x08) {
+		/* Op state when first two registers overwritten with 0x00 */
+		cyapa->gen = CYAPA_GEN3;
+		cyapa->state = CYAPA_STATE_OP;
+	} else if (reg_data[REG_BL_STATUS] &
+			(BL_STATUS_RUNNING | BL_STATUS_BUSY)) {
+		cyapa->gen = CYAPA_GEN3;
+		cyapa->state = CYAPA_STATE_BL_BUSY;
+	}
+
+	if (cyapa->gen == CYAPA_GEN3 && (cyapa->state == CYAPA_STATE_OP ||
+		cyapa->state == CYAPA_STATE_BL_IDLE ||
+		cyapa->state == CYAPA_STATE_BL_ACTIVE ||
+		cyapa->state == CYAPA_STATE_BL_BUSY))
+		return 0;
+
+	return -EAGAIN;
+}
+
+static int cyapa_gen3_bl_deactivate(struct cyapa *cyapa)
+{
+	int error;
+
+	error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_deactivate),
+					bl_deactivate);
+	if (error)
+		return error;
+
+	/* Wait for bootloader to switch to idle state; should take < 100ms */
+	msleep(100);
+	error = cyapa_poll_state(cyapa, 500);
+	if (error)
+		return error;
+	if (cyapa->state != CYAPA_STATE_BL_IDLE)
+		return -EAGAIN;
+	return 0;
+}
+
+/*
+ * Exit bootloader
+ *
+ * Send bl_exit command, then wait 50 - 100 ms to let device transition to
+ * operational mode.  If this is the first time the device's firmware is
+ * running, it can take up to 2 seconds to calibrate its sensors.  So, poll
+ * the device's new state for up to 2 seconds.
+ *
+ * Returns:
+ *   -EIO    failure while reading from device
+ *   -EAGAIN device is stuck in bootloader, b/c it has invalid firmware
+ *   0       device is supported and in operational mode
+ */
+static int cyapa_gen3_bl_exit(struct cyapa *cyapa)
+{
+	int error;
+
+	error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_exit), bl_exit);
+	if (error)
+		return error;
+
+	/*
+	 * Wait for bootloader to exit, and operation mode to start.
+	 * Normally, this takes at least 50 ms.
+	 */
+	usleep_range(50000, 100000);
+	/*
+	 * In addition, when a device boots for the first time after being
+	 * updated to new firmware, it must first calibrate its sensors, which
+	 * can take up to an additional 2 seconds. If the device power is
+	 * running low, this may take even longer.
+	 */
+	error = cyapa_poll_state(cyapa, 4000);
+	if (error < 0)
+		return error;
+	if (cyapa->state != CYAPA_STATE_OP)
+		return -EAGAIN;
+
+	return 0;
+}
+
+/*
+ * cyapa_get_wait_time_for_pwr_cmd
+ *
+ * Compute the amount of time we need to wait after updating the touchpad
+ * power mode. The touchpad needs to consume the incoming power mode set
+ * command at the current clock rate.
+ */
+
+static u16 cyapa_get_wait_time_for_pwr_cmd(u8 pwr_mode)
+{
+	switch (pwr_mode) {
+	case PWR_MODE_FULL_ACTIVE: return 20;
+	case PWR_MODE_BTN_ONLY: return 20;
+	case PWR_MODE_OFF: return 20;
+	default: return cyapa_pwr_cmd_to_sleep_time(pwr_mode) + 50;
+	}
+}
+
+/*
+ * Set device power mode
+ *
+ * Write to the field to configure power state. Power states include :
+ *   Full : Max scans and report rate.
+ *   Idle : Report rate set by user specified time.
+ *   ButtonOnly : No scans for fingers. When the button is triggered,
+ *     a slave interrupt is asserted to notify host to wake up.
+ *   Off : Only awake for i2c commands from host. No function for button
+ *     or touch sensors.
+ *
+ * The power_mode command should conform to the following :
+ *   Full : 0x3f
+ *   Idle : Configurable from 20 to 1000ms. See note below for
+ *     cyapa_sleep_time_to_pwr_cmd and cyapa_pwr_cmd_to_sleep_time
+ *   ButtonOnly : 0x01
+ *   Off : 0x00
+ *
+ * Device power mode can only be set when device is in operational mode.
+ */
+static int cyapa_gen3_set_power_mode(struct cyapa *cyapa, u8 power_mode,
+		u16 always_unused)
+{
+	int ret;
+	u8 power;
+	int tries;
+	u16 sleep_time;
+
+	always_unused = 0;
+	if (cyapa->state != CYAPA_STATE_OP)
+		return 0;
+
+	tries = SET_POWER_MODE_TRIES;
+	while (tries--) {
+		ret = cyapa_read_byte(cyapa, CYAPA_CMD_POWER_MODE);
+		if (ret >= 0)
+			break;
+		usleep_range(SET_POWER_MODE_DELAY, 2 * SET_POWER_MODE_DELAY);
+	}
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Return early if the power mode to set is the same as the current
+	 * one.
+	 */
+	if ((ret & PWR_MODE_MASK) == power_mode)
+		return 0;
+
+	sleep_time = cyapa_get_wait_time_for_pwr_cmd(ret & PWR_MODE_MASK);
+	power = ret;
+	power &= ~PWR_MODE_MASK;
+	power |= power_mode & PWR_MODE_MASK;
+	tries = SET_POWER_MODE_TRIES;
+	while (tries--) {
+		ret = cyapa_write_byte(cyapa, CYAPA_CMD_POWER_MODE, power);
+		if (!ret)
+			break;
+		usleep_range(SET_POWER_MODE_DELAY, 2 * SET_POWER_MODE_DELAY);
+	}
+
+	/*
+	 * Wait for the newly set power command to go in at the previous
+	 * clock speed (scanrate) used by the touchpad firmware. Not
+	 * doing so before issuing the next command may result in errors
+	 * depending on the command's content.
+	 */
+	msleep(sleep_time);
+	return ret;
+}
+
+static int cyapa_gen3_get_query_data(struct cyapa *cyapa)
+{
+	u8 query_data[QUERY_DATA_SIZE];
+	int ret;
+
+	if (cyapa->state != CYAPA_STATE_OP)
+		return -EBUSY;
+
+	ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_QUERY, query_data);
+	if (ret != QUERY_DATA_SIZE)
+		return (ret < 0) ? ret : -EIO;
+
+	memcpy(&cyapa->product_id[0], &query_data[0], 5);
+	cyapa->product_id[5] = '-';
+	memcpy(&cyapa->product_id[6], &query_data[5], 6);
+	cyapa->product_id[12] = '-';
+	memcpy(&cyapa->product_id[13], &query_data[11], 2);
+	cyapa->product_id[15] = '\0';
+
+	cyapa->fw_maj_ver = query_data[15];
+	cyapa->fw_min_ver = query_data[16];
+
+	cyapa->btn_capability = query_data[19] & CAPABILITY_BTN_MASK;
+
+	cyapa->gen = query_data[20] & 0x0f;
+
+	cyapa->max_abs_x = ((query_data[21] & 0xf0) << 4) | query_data[22];
+	cyapa->max_abs_y = ((query_data[21] & 0x0f) << 8) | query_data[23];
+
+	cyapa->physical_size_x =
+		((query_data[24] & 0xf0) << 4) | query_data[25];
+	cyapa->physical_size_y =
+		((query_data[24] & 0x0f) << 8) | query_data[26];
+
+	cyapa->max_z = 255;
+
+	return 0;
+}
+
+static int cyapa_gen3_bl_query_data(struct cyapa *cyapa)
+{
+	u8 bl_data[CYAPA_CMD_LEN];
+	int ret;
+
+	ret = cyapa_i2c_reg_read_block(cyapa, 0, CYAPA_CMD_LEN, bl_data);
+	if (ret != CYAPA_CMD_LEN)
+		return (ret < 0) ? ret : -EIO;
+
+	/*
+	 * This value will be updated again when entered application mode.
+	 * If TP failed to enter application mode, this fw version values
+	 * can be used as a reference.
+	 * This firmware version valid when fw image checksum is valid.
+	 */
+	if (bl_data[REG_BL_STATUS] ==
+			(BL_STATUS_RUNNING | BL_STATUS_CSUM_VALID)) {
+		cyapa->fw_maj_ver = bl_data[GEN3_BL_IDLE_FW_MAJ_VER_OFFSET];
+		cyapa->fw_min_ver = bl_data[GEN3_BL_IDLE_FW_MIN_VER_OFFSET];
+	}
+
+	return 0;
+}
+
+/*
+ * Check if device is operational.
+ *
+ * An operational device is responding, has exited bootloader, and has
+ * firmware supported by this driver.
+ *
+ * Returns:
+ *   -EBUSY  no device or in bootloader
+ *   -EIO    failure while reading from device
+ *   -EAGAIN device is still in bootloader
+ *           if ->state = CYAPA_STATE_BL_IDLE, device has invalid firmware
+ *   -EINVAL device is in operational mode, but not supported by this driver
+ *   0       device is supported
+ */
+static int cyapa_gen3_do_operational_check(struct cyapa *cyapa)
+{
+	struct device *dev = &cyapa->client->dev;
+	int error;
+
+	switch (cyapa->state) {
+	case CYAPA_STATE_BL_ACTIVE:
+		error = cyapa_gen3_bl_deactivate(cyapa);
+		if (error) {
+			dev_err(dev, "failed to bl_deactivate: %d\n", error);
+			return error;
+		}
+
+	/* Fallthrough state */
+	case CYAPA_STATE_BL_IDLE:
+		/* Try to get firmware version in bootloader mode. */
+		cyapa_gen3_bl_query_data(cyapa);
+
+		error = cyapa_gen3_bl_exit(cyapa);
+		if (error) {
+			dev_err(dev, "failed to bl_exit: %d\n", error);
+			return error;
+		}
+
+	/* Fallthrough state */
+	case CYAPA_STATE_OP:
+		/*
+		 * Reading query data before going back to the full mode
+		 * may cause problems, so we set the power mode first here.
+		 */
+		error = cyapa_gen3_set_power_mode(cyapa,
+				PWR_MODE_FULL_ACTIVE, 0);
+		if (error)
+			dev_err(dev, "%s: set full power mode failed: %d\n",
+				__func__, error);
+		error = cyapa_gen3_get_query_data(cyapa);
+		if (error < 0)
+			return error;
+
+		/* Only support firmware protocol gen3 */
+		if (cyapa->gen != CYAPA_GEN3) {
+			dev_err(dev, "unsupported protocol version (%d)",
+				cyapa->gen);
+			return -EINVAL;
+		}
+
+		/* Only support product ID starting with CYTRA */
+		if (memcmp(cyapa->product_id, product_id,
+				strlen(product_id)) != 0) {
+			dev_err(dev, "unsupported product ID (%s)\n",
+				cyapa->product_id);
+			return -EINVAL;
+		}
+
+		return 0;
+
+	default:
+		return -EIO;
+	}
+	return 0;
+}
+
+/*
+ * Return false, do not continue process
+ * Return true, continue process.
+ */
+static bool cyapa_gen3_irq_cmd_handler(struct cyapa *cyapa)
+{
+	/* Not gen3 irq command response, skip for continue. */
+	if (cyapa->gen != CYAPA_GEN3)
+		return true;
+
+	if (cyapa->operational)
+		return true;
+
+	/*
+	 * Driver in detecting or other interface function processing,
+	 * so, stop cyapa_gen3_irq_handler to continue process to
+	 * avoid unwanted to error detecting and processing.
+	 *
+	 * And also, avoid the periodicly accerted interrupts to be processed
+	 * as touch inputs when gen3 failed to launch into application mode,
+	 * which will cause gen3 stays in bootloader mode.
+	 */
+	return false;
+}
+
+static int cyapa_gen3_irq_handler(struct cyapa *cyapa)
+{
+	struct input_dev *input = cyapa->input;
+	struct device *dev = &cyapa->client->dev;
+	struct cyapa_reg_data data;
+	int num_fingers;
+	int ret;
+	int i;
+
+	ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_DATA, (u8 *)&data);
+	if (ret != sizeof(data)) {
+		dev_err(dev, "failed to read report data, (%d)\n", ret);
+		return -EINVAL;
+	}
+
+	if ((data.device_status & OP_STATUS_SRC) != OP_STATUS_SRC ||
+	    (data.device_status & OP_STATUS_DEV) != CYAPA_DEV_NORMAL ||
+	    (data.finger_btn & OP_DATA_VALID) != OP_DATA_VALID) {
+		dev_err(dev, "invalid device state bytes, %02x %02x\n",
+			data.device_status, data.finger_btn);
+		return -EINVAL;
+	}
+
+	num_fingers = (data.finger_btn >> 4) & 0x0f;
+	for (i = 0; i < num_fingers; i++) {
+		const struct cyapa_touch *touch = &data.touches[i];
+		/* Note: touch->id range is 1 to 15; slots are 0 to 14. */
+		int slot = touch->id - 1;
+
+		input_mt_slot(input, slot);
+		input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
+		input_report_abs(input, ABS_MT_POSITION_X,
+				 ((touch->xy_hi & 0xf0) << 4) | touch->x_lo);
+		input_report_abs(input, ABS_MT_POSITION_Y,
+				 ((touch->xy_hi & 0x0f) << 8) | touch->y_lo);
+		input_report_abs(input, ABS_MT_PRESSURE, touch->pressure);
+	}
+
+	input_mt_sync_frame(input);
+
+	if (cyapa->btn_capability & CAPABILITY_LEFT_BTN_MASK)
+		input_report_key(input, BTN_LEFT,
+				 !!(data.finger_btn & OP_DATA_LEFT_BTN));
+	if (cyapa->btn_capability & CAPABILITY_MIDDLE_BTN_MASK)
+		input_report_key(input, BTN_MIDDLE,
+				 !!(data.finger_btn & OP_DATA_MIDDLE_BTN));
+	if (cyapa->btn_capability & CAPABILITY_RIGHT_BTN_MASK)
+		input_report_key(input, BTN_RIGHT,
+				 !!(data.finger_btn & OP_DATA_RIGHT_BTN));
+	input_sync(input);
+
+	return 0;
+}
+
+static int cyapa_gen3_initialize(struct cyapa *cyapa) { return 0; }
+static int cyapa_gen3_empty_output_data(struct cyapa *cyapa,
+		u8 *buf, int *len, cb_sort func) { return 0; }
+
+const struct cyapa_dev_ops cyapa_gen3_ops = {
+	.initialize = cyapa_gen3_initialize,
+
+	.state_parse = cyapa_gen3_state_parse,
+	.operational_check = cyapa_gen3_do_operational_check,
+
+	.irq_handler = cyapa_gen3_irq_handler,
+	.irq_cmd_handler = cyapa_gen3_irq_cmd_handler,
+	.sort_empty_output_data = cyapa_gen3_empty_output_data,
+	.set_power_mode = cyapa_gen3_set_power_mode,
+};
