diff mbox series

[v2,1/1] HID: ft260: add usb hid to i2c host bridge driver

Message ID 20210219163644.2811-2-michael.zaidman@gmail.com (mailing list archive)
State New
Headers show
Series HID: ft260: add usb hid to i2c host bridge driver | expand

Commit Message

Michael Zaidman Feb. 19, 2021, 4:36 p.m. UTC
The FTDI FT260 chip implements USB to I2C/UART bridges through two
USB HID class interfaces. The first - for I2C, and the second for UART.
Each interface is independent, and the kernel detects it as a separate
USB hidraw device.

This commit adds I2C host adapter support.

Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
---
 MAINTAINERS             |    7 +
 drivers/hid/Kconfig     |   11 +
 drivers/hid/Makefile    |    1 +
 drivers/hid/hid-ft260.c | 1053 +++++++++++++++++++++++++++++++++++++++
 drivers/hid/hid-ids.h   |    1 +
 5 files changed, 1073 insertions(+)
 create mode 100644 drivers/hid/hid-ft260.c

Comments

Aaron Jones March 4, 2021, 11:14 a.m. UTC | #1
From: Aaron Jones(FTDI-UK) <aaron.jones@ftdichip.com>

On Fri, Feb 19, 2021 at 06:36:44PM +0200, Michael Zaidman wrote:
> The FTDI FT260 chip implements USB to I2C/UART bridges through two
> USB HID class interfaces. The first - for I2C, and the second for UART.
> Each interface is independent, and the kernel detects it as a separate
> USB hidraw device.
>
> This commitadds I2C host adapter support.
>
> Signed-off-by:Michael Zaidman <michael.zaidman@gmail.com>

I've applied the patch, ran some tests with a UMFT260EV1A evaluation board, and found no issues with the functionality it provides.

Tested-by: Aaron Jones (FTDI-UK) <aaron.jones@ftdichip.com>
Registered in Scotland No 136640
This message contains confidential information and is intended only for the individual named. If you are not the named addressee you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this e-mail by mistake and delete this e-mail from your system. E-mail transmission cannot be guaranteed to be secure or error-free as information could be intercepted, lost, destroyed, arrive late or incomplete. The sender therefore does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail transmission. Future Technology Devices International Ltd has taken every reasonable precaution to ensure that any attachment to this e-mail has been swept for viruses. However, we cannot accept liability for any damage sustained as a result of software viruses and would advise that you carry out your own virus checks before opening any attachment.

Please note FTDI have updated their Privacy Policy.

Please click on the following link to access and review.

FTDI Privacy Policy<http://www.ftdichip.com/Corporate/PrivacyPolicy.htm>
Michael Zaidman March 4, 2021, 12:46 p.m. UTC | #2
On Thu, Mar 04, 2021 at 11:14:06AM +0000, Aaron Jones wrote:
> From: Aaron Jones(FTDI-UK) <aaron.jones@ftdichip.com>
> 
> On Fri, Feb 19, 2021 at 06:36:44PM +0200, Michael Zaidman wrote:
> > The FTDI FT260 chip implements USB to I2C/UART bridges through two
> > USB HID class interfaces. The first - for I2C, and the second for UART.
> > Each interface is independent, and the kernel detects it as a separate
> > USB hidraw device.
> >
> > This commit adds I2C host adapter support.
> >
> > Signed-off-by:Michael Zaidman <michael.zaidman@gmail.com>
> 
> I've applied the patch, ran some tests with a UMFT260EV1A evaluation board,
> and found no issues with the functionality it provides.
> 
> Tested-by: Aaron Jones (FTDI-UK) <aaron.jones@ftdichip.com>

Aaron, thanks for giving it a try - much appreciated!

I will add your "Tested-by:" to the next version of the patch
once I receive any feedback.
Jiri Kosina March 16, 2021, 7:25 a.m. UTC | #3
On Thu, 4 Mar 2021, Michael Zaidman wrote:

> > > The FTDI FT260 chip implements USB to I2C/UART bridges through two
> > > USB HID class interfaces. The first - for I2C, and the second for UART.
> > > Each interface is independent, and the kernel detects it as a separate
> > > USB hidraw device.
> > >
> > > This commit adds I2C host adapter support.
> > >
> > > Signed-off-by:Michael Zaidman <michael.zaidman@gmail.com>
> > 
> > I've applied the patch, ran some tests with a UMFT260EV1A evaluation board,
> > and found no issues with the functionality it provides.
> > 
> > Tested-by: Aaron Jones (FTDI-UK) <aaron.jones@ftdichip.com>
> 
> Aaron, thanks for giving it a try - much appreciated!

I have now queued the driver in hid.git#for-5.13/ft260. Thanks,
diff mbox series

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index 8a6fe5389d7d..30526cfd4994 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7328,6 +7328,13 @@  F:	fs/verity/
 F:	include/linux/fsverity.h
 F:	include/uapi/linux/fsverity.h
 
+FT260 FTDI USB-HID TO I2C BRIDGE DRIVER
+M:	Michael Zaidman <michael.zaidman@gmail.com>
+L:	linux-i2c@vger.kernel.org
+L:	linux-input@vger.kernel.org
+S:	Maintained
+F:	drivers/hid/hid-ft260.c
+
 FUJITSU LAPTOP EXTRAS
 M:	Jonathan Woithe <jwoithe@just42.net>
 L:	platform-driver-x86@vger.kernel.org
diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig
index 786b71ef7738..b279c6130bc2 100644
--- a/drivers/hid/Kconfig
+++ b/drivers/hid/Kconfig
@@ -351,6 +351,17 @@  config HID_EZKEY
 	help
 	Support for Ezkey BTC 8193 keyboard.
 
+config HID_FT260
+	tristate "FTDI FT260 USB HID to I2C host support"
+	depends on USB_HID && HIDRAW && I2C
+	help
+	  Provides I2C host adapter functionality over USB-HID through FT260
+	  device. The customizable USB descriptor fields are exposed as sysfs
+	  attributes.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called hid-ft260.
+
 config HID_GEMBIRD
 	tristate "Gembird Joypad"
 	depends on HID
diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile
index c4f6d5c613dc..6e24c37132ec 100644
--- a/drivers/hid/Makefile
+++ b/drivers/hid/Makefile
@@ -46,6 +46,7 @@  obj-$(CONFIG_HID_ELAN)		+= hid-elan.o
 obj-$(CONFIG_HID_ELECOM)	+= hid-elecom.o
 obj-$(CONFIG_HID_ELO)		+= hid-elo.o
 obj-$(CONFIG_HID_EZKEY)		+= hid-ezkey.o
+obj-$(CONFIG_HID_FT260)		+= hid-ft260.o
 obj-$(CONFIG_HID_GEMBIRD)	+= hid-gembird.o
 obj-$(CONFIG_HID_GFRM)		+= hid-gfrm.o
 obj-$(CONFIG_HID_GLORIOUS)  += hid-glorious.o
diff --git a/drivers/hid/hid-ft260.c b/drivers/hid/hid-ft260.c
new file mode 100644
index 000000000000..047aa85a7c83
--- /dev/null
+++ b/drivers/hid/hid-ft260.c
@@ -0,0 +1,1053 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * hid-ft260.c - FTDI FT260 USB HID to I2C host bridge
+ *
+ * Copyright (c) 2021, Michael Zaidman <michaelz@xsightlabs.com>
+ *
+ * Data Sheet:
+ *   https://www.ftdichip.com/Support/Documents/DataSheets/ICs/DS_FT260.pdf
+ */
+
+#include "hid-ids.h"
+#include <linux/hidraw.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+
+#ifdef DEBUG
+static int ft260_debug = 1;
+#else
+static int ft260_debug;
+#endif
+module_param_named(debug, ft260_debug, int, 0600);
+MODULE_PARM_DESC(debug, "Toggle FT260 debugging messages");
+
+#define ft260_dbg(format, arg...)					  \
+	do {								  \
+		if (ft260_debug)					  \
+			pr_info("%s: " format, __func__, ##arg);	  \
+	} while (0)
+
+#define FT260_REPORT_MAX_LENGTH (64)
+#define FT260_I2C_DATA_REPORT_ID(len) (FT260_I2C_REPORT_MIN + (len - 1) / 4)
+/*
+ * The input report format assigns 62 bytes for the data payload, but ft260
+ * returns 60 and 2 in two separate transactions. To minimize transfer time
+ * in reading chunks mode, set the maximum read payload length to 60 bytes.
+ */
+#define FT260_RD_DATA_MAX (60)
+#define FT260_WR_DATA_MAX (60)
+
+/*
+ * Device interface configuration.
+ * The FT260 has 2 interfaces that are controlled by DCNF0 and DCNF1 pins.
+ * First implementes USB HID to I2C bridge function and
+ * second - USB HID to UART bridge function.
+ */
+enum {
+	FT260_MODE_ALL			= 0x00,
+	FT260_MODE_I2C			= 0x01,
+	FT260_MODE_UART			= 0x02,
+	FT260_MODE_BOTH			= 0x03,
+};
+
+/* Control pipe */
+enum {
+	FT260_GET_RQST_TYPE		= 0xA1,
+	FT260_GET_REPORT		= 0x01,
+	FT260_SET_RQST_TYPE		= 0x21,
+	FT260_SET_REPORT		= 0x09,
+	FT260_FEATURE			= 0x03,
+};
+
+/* Report IDs / Feature In */
+enum {
+	FT260_CHIP_VERSION		= 0xA0,
+	FT260_SYSTEM_SETTINGS		= 0xA1,
+	FT260_I2C_STATUS		= 0xC0,
+	FT260_I2C_READ_REQ		= 0xC2,
+	FT260_I2C_REPORT_MIN		= 0xD0,
+	FT260_I2C_REPORT_MAX		= 0xDE,
+	FT260_GPIO			= 0xB0,
+	FT260_UART_INTERRUPT_STATUS	= 0xB1,
+	FT260_UART_STATUS		= 0xE0,
+	FT260_UART_RI_DCD_STATUS	= 0xE1,
+	FT260_UART_REPORT		= 0xF0,
+};
+
+/* Feature Out */
+enum {
+	FT260_SET_CLOCK			= 0x01,
+	FT260_SET_I2C_MODE		= 0x02,
+	FT260_SET_UART_MODE		= 0x03,
+	FT260_ENABLE_INTERRUPT		= 0x05,
+	FT260_SELECT_GPIO2_FUNC		= 0x06,
+	FT260_ENABLE_UART_DCD_RI	= 0x07,
+	FT260_SELECT_GPIOA_FUNC		= 0x08,
+	FT260_SELECT_GPIOG_FUNC		= 0x09,
+	FT260_SET_INTERRUPT_TRIGGER	= 0x0A,
+	FT260_SET_SUSPEND_OUT_POLAR	= 0x0B,
+	FT260_ENABLE_UART_RI_WAKEUP	= 0x0C,
+	FT260_SET_UART_RI_WAKEUP_CFG	= 0x0D,
+	FT260_SET_I2C_RESET		= 0x20,
+	FT260_SET_I2C_CLOCK_SPEED	= 0x22,
+	FT260_SET_UART_RESET		= 0x40,
+	FT260_SET_UART_CONFIG		= 0x41,
+	FT260_SET_UART_BAUD_RATE	= 0x42,
+	FT260_SET_UART_DATA_BIT		= 0x43,
+	FT260_SET_UART_PARITY		= 0x44,
+	FT260_SET_UART_STOP_BIT		= 0x45,
+	FT260_SET_UART_BREAKING		= 0x46,
+	FT260_SET_UART_XON_XOFF		= 0x49,
+};
+
+/* Response codes in I2C status report */
+enum {
+	FT260_I2C_STATUS_SUCCESS	= 0x00,
+	FT260_I2C_STATUS_CTRL_BUSY	= 0x01,
+	FT260_I2C_STATUS_ERROR		= 0x02,
+	FT260_I2C_STATUS_ADDR_NO_ACK	= 0x04,
+	FT260_I2C_STATUS_DATA_NO_ACK	= 0x08,
+	FT260_I2C_STATUS_ARBITR_LOST	= 0x10,
+	FT260_I2C_STATUS_CTRL_IDLE	= 0x20,
+	FT260_I2C_STATUS_BUS_BUSY	= 0x40,
+};
+
+/* I2C Conditions flags */
+enum {
+	FT260_FLAG_NONE			= 0x00,
+	FT260_FLAG_START		= 0x02,
+	FT260_FLAG_START_REPEATED	= 0x03,
+	FT260_FLAG_STOP			= 0x04,
+	FT260_FLAG_START_STOP		= 0x06,
+	FT260_FLAG_START_STOP_REPEATED	= 0x07,
+};
+
+#define FT260_SET_REQUEST_VALUE(report_id) ((FT260_FEATURE << 8) | report_id)
+
+/* Feature In reports */
+
+struct ft260_get_chip_version_report {
+	u8 report;		/* FT260_CHIP_VERSION */
+	u8 chip_code[4];	/* FTDI chip identification code */
+	u8 reserved[8];
+} __packed;
+
+struct ft260_get_system_status_report {
+	u8 report;		/* FT260_SYSTEM_SETTINGS */
+	u8 chip_mode;		/* DCNF0 and DCNF1 status, bits 0-1 */
+	u8 clock_ctl;		/* 0 - 12MHz, 1 - 24MHz, 2 - 48MHz */
+	u8 suspend_status;	/* 0 - not suspended, 1 - suspended */
+	u8 pwren_status;	/* 0 - FT260 is not ready, 1 - ready */
+	u8 i2c_enable;		/* 0 - disabled, 1 - enabled */
+	u8 uart_mode;		/* 0 - OFF; 1 - RTS_CTS, 2 - DTR_DSR, */
+				/* 3 - XON_XOFF, 4 - No flow control */
+	u8 hid_over_i2c_en;	/* 0 - disabled, 1 - enabled */
+	u8 gpio2_function;	/* 0 - GPIO,  1 - SUSPOUT, */
+				/* 2 - PWREN, 4 - TX_LED */
+	u8 gpioA_function;	/* 0 - GPIO, 3 - TX_ACTIVE, 4 - TX_LED */
+	u8 gpioG_function;	/* 0 - GPIO, 2 - PWREN, */
+				/* 5 - RX_LED, 6 - BCD_DET */
+	u8 suspend_out_pol;	/* 0 - active-high, 1 - active-low */
+	u8 enable_wakeup_int;	/* 0 - disabled, 1 - enabled */
+	u8 intr_cond;		/* Interrupt trigger conditions */
+	u8 power_saving_en;	/* 0 - disabled, 1 - enabled */
+	u8 reserved[10];
+} __packed;
+
+struct ft260_get_i2c_status_report {
+	u8 report;		/* FT260_I2C_STATUS */
+	u8 bus_status;		/* I2C bus status */
+	__le16 clock;		/* I2C bus clock in range 60-3400 KHz */
+	u8 reserved;
+} __packed;
+
+/* Feature Out reports */
+
+struct ft260_set_system_clock_report {
+	u8 report;		/* FT260_SYSTEM_SETTINGS */
+	u8 request;		/* FT260_SET_CLOCK */
+	u8 clock_ctl;		/* 0 - 12MHz, 1 - 24MHz, 2 - 48MHz */
+} __packed;
+
+struct ft260_set_i2c_mode_report {
+	u8 report;		/* FT260_SYSTEM_SETTINGS */
+	u8 request;		/* FT260_SET_I2C_MODE */
+	u8 i2c_enable;		/* 0 - disabled, 1 - enabled */
+} __packed;
+
+struct ft260_set_uart_mode_report {
+	u8 report;		/* FT260_SYSTEM_SETTINGS */
+	u8 request;		/* FT260_SET_UART_MODE */
+	u8 uart_mode;		/* 0 - OFF; 1 - RTS_CTS, 2 - DTR_DSR, */
+				/* 3 - XON_XOFF, 4 - No flow control */
+} __packed;
+
+struct ft260_set_i2c_reset_report {
+	u8 report;		/* FT260_SYSTEM_SETTINGS */
+	u8 request;		/* FT260_SET_I2C_RESET */
+} __packed;
+
+struct ft260_set_i2c_speed_report {
+	u8 report;		/* FT260_SYSTEM_SETTINGS */
+	u8 request;		/* FT260_SET_I2C_CLOCK_SPEED */
+	__le16 clock;		/* I2C bus clock in range 60-3400 KHz */
+} __packed;
+
+/* Data transfer reports */
+
+struct ft260_i2c_write_request_report {
+	u8 report;		/* FT260_I2C_REPORT */
+	u8 address;		/* 7-bit I2C address */
+	u8 flag;		/* I2C transaction condition */
+	u8 length;		/* data payload length */
+	u8 data[60];		/* data payload */
+} __packed;
+
+struct ft260_i2c_read_request_report {
+	u8 report;		/* FT260_I2C_READ_REQ */
+	u8 address;		/* 7-bit I2C address */
+	u8 flag;		/* I2C transaction condition */
+	__le16 length;		/* data payload length */
+} __packed;
+
+struct ft260_i2c_input_report {
+	u8 report;		/* FT260_I2C_REPORT */
+	u8 length;		/* data payload length */
+	u8 data[2];		/* data payload */
+} __packed;
+
+static const struct hid_device_id ft260_devices[] = {
+	{ HID_USB_DEVICE(USB_VENDOR_ID_FUTURE_TECHNOLOGY,
+			 USB_DEVICE_ID_FT260) },
+	{ /* END OF LIST */ }
+};
+MODULE_DEVICE_TABLE(hid, ft260_devices);
+
+struct ft260_device {
+	struct i2c_adapter adap;
+	struct hid_device *hdev;
+	struct completion wait;
+	struct mutex lock;
+	u8 write_buf[FT260_REPORT_MAX_LENGTH];
+	u8 *read_buf;
+	u16 read_idx;
+	u16 read_len;
+	u16 clock;
+};
+
+static int ft260_hid_feature_report_get(struct hid_device *hdev,
+					unsigned char report_id, u8 *data,
+					size_t len)
+{
+	u8 *buf;
+	int ret;
+
+	buf = kmalloc(len, GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	ret = hid_hw_raw_request(hdev, report_id, buf, len, HID_FEATURE_REPORT,
+				 HID_REQ_GET_REPORT);
+	memcpy(data, buf, len);
+	kfree(buf);
+	return ret;
+}
+
+static int ft260_hid_feature_report_set(struct hid_device *hdev, u8 *data,
+					size_t len)
+{
+	u8 *buf;
+	int ret;
+
+	buf = kmemdup(data, len, GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	buf[0] = FT260_SYSTEM_SETTINGS;
+
+	ret = hid_hw_raw_request(hdev, buf[0], buf, len, HID_FEATURE_REPORT,
+				 HID_REQ_SET_REPORT);
+
+	kfree(buf);
+	return ret;
+}
+
+static int ft260_i2c_reset(struct hid_device *hdev)
+{
+	struct ft260_set_i2c_reset_report report;
+	int ret;
+
+	report.request = FT260_SET_I2C_RESET;
+
+	ret = ft260_hid_feature_report_set(hdev, (u8 *)&report, sizeof(report));
+	if (ret < 0) {
+		hid_err(hdev, "failed to reset I2C controller: %d\n", ret);
+		return ret;
+	}
+
+	ft260_dbg("done\n");
+	return ret;
+}
+
+static int ft260_xfer_status(struct ft260_device *dev)
+{
+	struct hid_device *hdev = dev->hdev;
+	struct ft260_get_i2c_status_report report;
+	int ret;
+
+	ret = ft260_hid_feature_report_get(hdev, FT260_I2C_STATUS,
+					   (u8 *)&report, sizeof(report));
+	if (ret < 0) {
+		hid_err(hdev, "failed to retrieve status: %d\n", ret);
+		return ret;
+	}
+
+	dev->clock = le16_to_cpu(report.clock);
+	ft260_dbg("bus_status %#02x, clock %u\n", report.bus_status,
+		  dev->clock);
+
+	if (report.bus_status & FT260_I2C_STATUS_CTRL_BUSY)
+		return -EAGAIN;
+
+	if (report.bus_status & FT260_I2C_STATUS_BUS_BUSY)
+		return -EBUSY;
+
+	if (report.bus_status & FT260_I2C_STATUS_ERROR)
+		return -EIO;
+
+	ret = -EIO;
+
+	if (report.bus_status & FT260_I2C_STATUS_ADDR_NO_ACK)
+		ft260_dbg("unacknowledged address\n");
+
+	if (report.bus_status & FT260_I2C_STATUS_DATA_NO_ACK)
+		ft260_dbg("unacknowledged data\n");
+
+	if (report.bus_status & FT260_I2C_STATUS_ARBITR_LOST)
+		ft260_dbg("arbitration loss\n");
+
+	if (report.bus_status & FT260_I2C_STATUS_CTRL_IDLE)
+		ret = 0;
+
+	return ret;
+}
+
+static int ft260_hid_output_report(struct hid_device *hdev, u8 *data,
+				   size_t len)
+{
+	u8 *buf;
+	int ret;
+
+	buf = kmemdup(data, len, GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	ret = hid_hw_output_report(hdev, buf, len);
+
+	kfree(buf);
+	return ret;
+}
+
+static int ft260_hid_output_report_check_status(struct ft260_device *dev,
+						u8 *data, int len)
+{
+	int ret, usec, try = 3;
+	struct hid_device *hdev = dev->hdev;
+
+	ret = ft260_hid_output_report(hdev, data, len);
+	if (ret < 0) {
+		hid_err(hdev, "%s: failed to start transfer, ret %d\n",
+			__func__, ret);
+		ft260_i2c_reset(hdev);
+		return ret;
+	}
+
+	/* transfer time = 1 / clock(KHz) * 10 bits * bytes */
+	usec = 10000 / dev->clock * len;
+	usleep_range(usec, usec + 100);
+	ft260_dbg("wait %d usec, len %d\n", usec, len);
+	do {
+		ret = ft260_xfer_status(dev);
+		if (ret != -EAGAIN)
+			break;
+	} while (--try);
+
+	if (ret == 0 || ret == -EBUSY)
+		return 0;
+
+	ft260_i2c_reset(hdev);
+	return -EIO;
+}
+
+static int ft260_i2c_write(struct ft260_device *dev, u8 addr, u8 *data,
+			   int data_len, u8 flag)
+{
+	int len, ret, idx = 0;
+	struct hid_device *hdev = dev->hdev;
+	struct ft260_i2c_write_request_report *rep =
+		(struct ft260_i2c_write_request_report *)dev->write_buf;
+
+	do {
+		if (data_len <= FT260_WR_DATA_MAX)
+			len = data_len;
+		else
+			len = FT260_WR_DATA_MAX;
+
+		rep->report = FT260_I2C_DATA_REPORT_ID(len);
+		rep->address = addr;
+		rep->length = len;
+		rep->flag = flag;
+
+		memcpy(rep->data, &data[idx], len);
+
+		ft260_dbg("rep %#02x addr %#02x off %d len %d d[0] %#02x\n",
+			  rep->report, addr, idx, len, data[0]);
+
+		ret = ft260_hid_output_report_check_status(dev, (u8 *)rep,
+							   len + 4);
+		if (ret < 0) {
+			hid_err(hdev, "%s: failed to start transfer, ret %d\n",
+				__func__, ret);
+			return ret;
+		}
+
+		data_len -= len;
+		idx += len;
+
+	} while (data_len > 0);
+
+	return 0;
+}
+
+static int ft260_smbus_write(struct ft260_device *dev, u8 addr, u8 cmd,
+			     u8 *data, u8 data_len, u8 flag)
+{
+	int ret = 0;
+	int len = 4;
+
+	struct ft260_i2c_write_request_report *rep =
+		(struct ft260_i2c_write_request_report *)dev->write_buf;
+
+	rep->address = addr;
+	rep->data[0] = cmd;
+	rep->length = data_len + 1;
+	rep->flag = flag;
+	len += rep->length;
+
+	rep->report = FT260_I2C_DATA_REPORT_ID(len);
+
+	if (data_len > 0)
+		memcpy(&rep->data[1], data, data_len);
+
+	ft260_dbg("rep %#02x addr %#02x cmd %#02x datlen %d replen %d\n",
+		  rep->report, addr, cmd, rep->length, len);
+
+	ret = ft260_hid_output_report_check_status(dev, (u8 *)rep, len);
+
+	return ret;
+}
+
+static int ft260_i2c_read(struct ft260_device *dev, u8 addr, u8 *data,
+			  u16 len, u8 flag)
+{
+	struct ft260_i2c_read_request_report rep;
+	struct hid_device *hdev = dev->hdev;
+	int timeout;
+	int ret;
+
+	if (len > FT260_RD_DATA_MAX) {
+		hid_err(hdev, "%s: unsupported rd len: %d\n", __func__, len);
+		return -EINVAL;
+	}
+
+	dev->read_idx = 0;
+	dev->read_buf = data;
+	dev->read_len = len;
+
+	rep.report = FT260_I2C_READ_REQ;
+	rep.length = cpu_to_le16(len);
+	rep.address = addr;
+	rep.flag = flag;
+
+	ft260_dbg("rep %#02x addr %#02x len %d\n", rep.report, rep.address,
+		  rep.length);
+
+	reinit_completion(&dev->wait);
+
+	ret = ft260_hid_output_report(hdev, (u8 *)&rep, sizeof(rep));
+	if (ret < 0) {
+		hid_err(hdev, "%s: failed to start transaction, ret %d\n",
+			__func__, ret);
+		return ret;
+	}
+
+	timeout = msecs_to_jiffies(5000);
+	if (!wait_for_completion_timeout(&dev->wait, timeout)) {
+		ft260_i2c_reset(hdev);
+		return -ETIMEDOUT;
+	}
+
+	ret = ft260_xfer_status(dev);
+	if (ret == 0)
+		return 0;
+
+	ft260_i2c_reset(hdev);
+	return -EIO;
+}
+
+/*
+ * A random read operation is implemented as a dummy write operation, followed
+ * by a current address read operation. The dummy write operation is used to
+ * load the target byte address into the current byte address counter, from
+ * which the subsequent current address read operation then reads.
+ */
+static int ft260_i2c_write_read(struct ft260_device *dev, struct i2c_msg *msgs)
+{
+	int len, ret;
+	u16 left_len = msgs[1].len;
+	u8 *read_buf = msgs[1].buf;
+	u8 addr = msgs[0].addr;
+	u16 read_off = 0;
+	struct hid_device *hdev = dev->hdev;
+
+	if (msgs[0].len > 2) {
+		hid_err(hdev, "%s: unsupported wr len: %d\n", __func__, len);
+		return -EOPNOTSUPP;
+	}
+
+	memcpy(&read_off, msgs[0].buf, msgs[0].len);
+
+	do {
+		if (left_len <= FT260_RD_DATA_MAX)
+			len = left_len;
+		else
+			len = FT260_RD_DATA_MAX;
+
+		ft260_dbg("read_off %#x left_len %d len %d\n", read_off,
+			  left_len, len);
+
+		ret = ft260_i2c_write(dev, addr, (u8 *)&read_off, msgs[0].len,
+				      FT260_FLAG_START);
+		if (ret < 0)
+			return ret;
+
+		ret = ft260_i2c_read(dev, addr, read_buf, len,
+				     FT260_FLAG_START_STOP);
+		if (ret < 0)
+			return ret;
+
+		left_len -= len;
+		read_buf += len;
+		read_off += len;
+
+	} while (left_len > 0);
+
+	return 0;
+}
+
+static int ft260_i2c_xfer(struct i2c_adapter *adapter, struct i2c_msg *msgs,
+			  int num)
+{
+	int ret;
+	struct ft260_device *dev = i2c_get_adapdata(adapter);
+	struct hid_device *hdev = dev->hdev;
+
+	mutex_lock(&dev->lock);
+
+	ret = hid_hw_power(hdev, PM_HINT_FULLON);
+	if (ret < 0) {
+		hid_err(hdev, "failed to enter FULLON power mode: %d\n", ret);
+		mutex_unlock(&dev->lock);
+		return ret;
+	}
+
+	if (num == 1) {
+		if (msgs->flags & I2C_M_RD)
+			ret = ft260_i2c_read(dev, msgs->addr, msgs->buf,
+					     msgs->len, FT260_FLAG_START_STOP);
+		else
+			ret = ft260_i2c_write(dev, msgs->addr, msgs->buf,
+					      msgs->len, FT260_FLAG_START_STOP);
+		if (ret < 0)
+			goto i2c_exit;
+
+	} else {
+		/* Combined write then read message */
+		ret = ft260_i2c_write_read(dev, msgs);
+		if (ret < 0)
+			goto i2c_exit;
+	}
+
+	ret = num;
+i2c_exit:
+	hid_hw_power(hdev, PM_HINT_NORMAL);
+	mutex_unlock(&dev->lock);
+	return ret;
+}
+
+static int ft260_smbus_xfer(struct i2c_adapter *adapter, u16 addr, u16 flags,
+			    char read_write, u8 cmd, int size,
+			    union i2c_smbus_data *data)
+{
+	int ret;
+	struct ft260_device *dev = i2c_get_adapdata(adapter);
+	struct hid_device *hdev = dev->hdev;
+
+	ft260_dbg("smbus size %d\n", size);
+
+	mutex_lock(&dev->lock);
+
+	ret = hid_hw_power(hdev, PM_HINT_FULLON);
+	if (ret < 0) {
+		hid_err(hdev, "power management error: %d\n", ret);
+		mutex_unlock(&dev->lock);
+		return ret;
+	}
+
+	switch (size) {
+	case I2C_SMBUS_QUICK:
+		if (read_write == I2C_SMBUS_READ)
+			ret = ft260_i2c_read(dev, addr, &data->byte, 0,
+					     FT260_FLAG_START_STOP);
+		else
+			ret = ft260_smbus_write(dev, addr, cmd, NULL, 0,
+						FT260_FLAG_START_STOP);
+		break;
+	case I2C_SMBUS_BYTE:
+		if (read_write == I2C_SMBUS_READ)
+			ret = ft260_i2c_read(dev, addr, &data->byte, 1,
+					     FT260_FLAG_START_STOP);
+		else
+			ret = ft260_smbus_write(dev, addr, cmd, NULL, 0,
+						FT260_FLAG_START_STOP);
+		break;
+	case I2C_SMBUS_BYTE_DATA:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = ft260_smbus_write(dev, addr, cmd, NULL, 0,
+						FT260_FLAG_START);
+			if (ret)
+				goto smbus_exit;
+
+			ret = ft260_i2c_read(dev, addr, &data->byte, 1,
+					     FT260_FLAG_START_STOP_REPEATED);
+		} else {
+			ret = ft260_smbus_write(dev, addr, cmd, &data->byte, 1,
+						FT260_FLAG_START_STOP);
+		}
+		break;
+	case I2C_SMBUS_WORD_DATA:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = ft260_smbus_write(dev, addr, cmd, NULL, 0,
+						FT260_FLAG_START);
+			if (ret)
+				goto smbus_exit;
+
+			ret = ft260_i2c_read(dev, addr, (u8 *)&data->word, 2,
+					     FT260_FLAG_START_STOP_REPEATED);
+		} else {
+			ret = ft260_smbus_write(dev, addr, cmd,
+						(u8 *)&data->word, 2,
+						FT260_FLAG_START_STOP);
+		}
+		break;
+	case I2C_SMBUS_BLOCK_DATA:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = ft260_smbus_write(dev, addr, cmd, NULL, 0,
+						FT260_FLAG_START);
+			if (ret)
+				goto smbus_exit;
+
+			ret = ft260_i2c_read(dev, addr, data->block,
+					     data->block[0] + 1,
+					     FT260_FLAG_START_STOP_REPEATED);
+		} else {
+			ret = ft260_smbus_write(dev, addr, cmd, data->block,
+						data->block[0] + 1,
+						FT260_FLAG_START_STOP);
+		}
+		break;
+	case I2C_SMBUS_I2C_BLOCK_DATA:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = ft260_smbus_write(dev, addr, cmd, NULL, 0,
+						FT260_FLAG_START);
+			if (ret)
+				goto smbus_exit;
+
+			ret = ft260_i2c_read(dev, addr, data->block + 1,
+					     data->block[0],
+					     FT260_FLAG_START_STOP_REPEATED);
+		} else {
+			ret = ft260_smbus_write(dev, addr, cmd, data->block + 1,
+						data->block[0],
+						FT260_FLAG_START_STOP);
+		}
+		break;
+	default:
+		hid_err(hdev, "unsupported smbus transaction size %d\n", size);
+		ret = -EOPNOTSUPP;
+	}
+
+smbus_exit:
+	hid_hw_power(hdev, PM_HINT_NORMAL);
+	mutex_unlock(&dev->lock);
+	return ret;
+}
+
+static u32 ft260_functionality(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_BYTE | I2C_FUNC_SMBUS_QUICK |
+	       I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA |
+	       I2C_FUNC_SMBUS_BLOCK_DATA | I2C_FUNC_SMBUS_I2C_BLOCK;
+}
+
+static const struct i2c_adapter_quirks ft260_i2c_quirks = {
+	.flags = I2C_AQ_COMB_WRITE_THEN_READ,
+	.max_comb_1st_msg_len = 2,
+};
+
+static const struct i2c_algorithm ft260_i2c_algo = {
+	.master_xfer = ft260_i2c_xfer,
+	.smbus_xfer = ft260_smbus_xfer,
+	.functionality = ft260_functionality,
+};
+
+static int ft260_get_system_config(struct hid_device *hdev,
+				   struct ft260_get_system_status_report *cfg)
+{
+	int ret;
+	int len = sizeof(struct ft260_get_system_status_report);
+
+	ret = ft260_hid_feature_report_get(hdev, FT260_SYSTEM_SETTINGS,
+					   (u8 *)cfg, len);
+	if (ret != len) {
+		hid_err(hdev, "failed to retrieve system status\n");
+		if (ret >= 0)
+			return -EIO;
+	}
+	return 0;
+}
+
+static int ft260_is_interface_enabled(struct hid_device *hdev)
+{
+	struct ft260_get_system_status_report cfg;
+	struct usb_interface *usbif = to_usb_interface(hdev->dev.parent);
+	int interface = usbif->cur_altsetting->desc.bInterfaceNumber;
+	int ret;
+
+	ret = ft260_get_system_config(hdev, &cfg);
+	if (ret)
+		return ret;
+
+	ft260_dbg("interface:  0x%02x\n", interface);
+	ft260_dbg("chip mode:  0x%02x\n", cfg.chip_mode);
+	ft260_dbg("clock_ctl:  0x%02x\n", cfg.clock_ctl);
+	ft260_dbg("i2c_enable: 0x%02x\n", cfg.i2c_enable);
+	ft260_dbg("uart_mode:  0x%02x\n", cfg.uart_mode);
+
+	switch (cfg.chip_mode) {
+	case FT260_MODE_ALL:
+	case FT260_MODE_BOTH:
+		if (interface == 1) {
+			hid_info(hdev, "uart interface is not supported\n");
+			return 0;
+		}
+		ret = 1;
+		break;
+	case FT260_MODE_UART:
+		if (interface == 0) {
+			hid_info(hdev, "uart is unsupported on interface 0\n");
+			ret = 0;
+		}
+		break;
+	case FT260_MODE_I2C:
+		if (interface == 1) {
+			hid_info(hdev, "i2c is unsupported on interface 1\n");
+			ret = 0;
+		}
+		break;
+	}
+	return ret;
+}
+
+static int ft260_byte_show(struct hid_device *hdev, int id, u8 *cfg, int len,
+			   u8 *field, u8 *buf)
+{
+	int ret;
+
+	ret = ft260_hid_feature_report_get(hdev, id, cfg, len);
+	if (ret != len && ret >= 0)
+		return -EIO;
+
+	return scnprintf(buf, PAGE_SIZE, "%hi\n", *field);
+}
+
+static int ft260_word_show(struct hid_device *hdev, int id, u8 *cfg, int len,
+			   u16 *field, u8 *buf)
+{
+	int ret;
+
+	ret = ft260_hid_feature_report_get(hdev, id, cfg, len);
+	if (ret != len && ret >= 0)
+		return -EIO;
+
+	return scnprintf(buf, PAGE_SIZE, "%hi\n", le16_to_cpu(*field));
+}
+
+#define FT260_ATTR_SHOW(name, reptype, id, type, func)			       \
+	static ssize_t name##_show(struct device *kdev,			       \
+				   struct device_attribute *attr, char *buf)   \
+	{								       \
+		struct reptype rep;					       \
+		struct hid_device *hdev = to_hid_device(kdev);		       \
+		type *field = &rep.name;				       \
+		int len = sizeof(rep);					       \
+									       \
+		return func(hdev, id, (u8 *)&rep, len, field, buf);	       \
+	}
+
+#define FT260_SSTAT_ATTR_SHOW(name)					       \
+		FT260_ATTR_SHOW(name, ft260_get_system_status_report,	       \
+				FT260_SYSTEM_SETTINGS, u8, ft260_byte_show)
+
+#define FT260_I2CST_ATTR_SHOW(name)					       \
+		FT260_ATTR_SHOW(name, ft260_get_i2c_status_report,	       \
+				FT260_I2C_STATUS, u16, ft260_word_show)
+
+#define FT260_ATTR_STORE(name, reptype, id, req, type, func)		       \
+	static ssize_t name##_store(struct device *kdev,		       \
+				    struct device_attribute *attr,	       \
+				    const char *buf, size_t count)	       \
+	{								       \
+		struct reptype rep;					       \
+		struct hid_device *hdev = to_hid_device(kdev);		       \
+		type name;						       \
+		int ret;						       \
+									       \
+		if (!func(buf, 10, &name)) {				       \
+			rep.name = name;				       \
+			rep.report = id;				       \
+			rep.request = req;				       \
+			ret = ft260_hid_feature_report_set(hdev, (u8 *)&rep,   \
+							   sizeof(rep));       \
+			if (!ret)					       \
+				ret = count;				       \
+		} else {						       \
+			ret = -EINVAL;					       \
+		}							       \
+		return ret;						       \
+	}
+
+#define FT260_BYTE_ATTR_STORE(name, reptype, req)			       \
+		FT260_ATTR_STORE(name, reptype, FT260_SYSTEM_SETTINGS, req,    \
+				 u8, kstrtou8)
+
+#define FT260_WORD_ATTR_STORE(name, reptype, req)			       \
+		FT260_ATTR_STORE(name, reptype, FT260_SYSTEM_SETTINGS, req,    \
+				 u16, kstrtou16)
+
+FT260_SSTAT_ATTR_SHOW(chip_mode);
+static DEVICE_ATTR_RO(chip_mode);
+
+FT260_SSTAT_ATTR_SHOW(pwren_status);
+static DEVICE_ATTR_RO(pwren_status);
+
+FT260_SSTAT_ATTR_SHOW(suspend_status);
+static DEVICE_ATTR_RO(suspend_status);
+
+FT260_SSTAT_ATTR_SHOW(hid_over_i2c_en);
+static DEVICE_ATTR_RO(hid_over_i2c_en);
+
+FT260_SSTAT_ATTR_SHOW(power_saving_en);
+static DEVICE_ATTR_RO(power_saving_en);
+
+FT260_SSTAT_ATTR_SHOW(i2c_enable);
+FT260_BYTE_ATTR_STORE(i2c_enable, ft260_set_i2c_mode_report,
+		      FT260_SET_I2C_MODE);
+static DEVICE_ATTR_RW(i2c_enable);
+
+FT260_SSTAT_ATTR_SHOW(uart_mode);
+FT260_BYTE_ATTR_STORE(uart_mode, ft260_set_uart_mode_report,
+		      FT260_SET_UART_MODE);
+static DEVICE_ATTR_RW(uart_mode);
+
+FT260_SSTAT_ATTR_SHOW(clock_ctl);
+FT260_BYTE_ATTR_STORE(clock_ctl, ft260_set_system_clock_report,
+		      FT260_SET_CLOCK);
+static DEVICE_ATTR_RW(clock_ctl);
+
+FT260_I2CST_ATTR_SHOW(clock);
+FT260_WORD_ATTR_STORE(clock, ft260_set_i2c_speed_report,
+		      FT260_SET_I2C_CLOCK_SPEED);
+static DEVICE_ATTR_RW(clock);
+
+static ssize_t i2c_reset_store(struct device *kdev,
+			       struct device_attribute *attr, const char *buf,
+			       size_t count)
+{
+	struct hid_device *hdev = to_hid_device(kdev);
+	int ret = ft260_i2c_reset(hdev);
+
+	if (ret)
+		return ret;
+	return count;
+}
+static DEVICE_ATTR_WO(i2c_reset);
+
+static const struct attribute_group ft260_attr_group = {
+	.attrs = (struct attribute *[]) {
+		  &dev_attr_chip_mode.attr,
+		  &dev_attr_pwren_status.attr,
+		  &dev_attr_suspend_status.attr,
+		  &dev_attr_hid_over_i2c_en.attr,
+		  &dev_attr_power_saving_en.attr,
+		  &dev_attr_i2c_enable.attr,
+		  &dev_attr_uart_mode.attr,
+		  &dev_attr_clock_ctl.attr,
+		  &dev_attr_i2c_reset.attr,
+		  &dev_attr_clock.attr,
+		  NULL
+	}
+};
+
+static int ft260_probe(struct hid_device *hdev, const struct hid_device_id *id)
+{
+	struct ft260_device *dev;
+	struct ft260_get_chip_version_report version;
+	int ret;
+
+	dev = devm_kzalloc(&hdev->dev, sizeof(*dev), GFP_KERNEL);
+	if (!dev)
+		return -ENOMEM;
+
+	ret = hid_parse(hdev);
+	if (ret) {
+		hid_err(hdev, "failed to parse HID\n");
+		return ret;
+	}
+
+	ret = hid_hw_start(hdev, HID_CONNECT_HIDRAW);
+	if (ret) {
+		hid_err(hdev, "failed to start HID HW\n");
+		return ret;
+	}
+
+	ret = hid_hw_open(hdev);
+	if (ret) {
+		hid_err(hdev, "failed to open HID HW\n");
+		goto err_hid_stop;
+	}
+
+	ret = ft260_hid_feature_report_get(hdev, FT260_CHIP_VERSION,
+					   (u8 *)&version, sizeof(version));
+	if (ret != sizeof(version)) {
+		hid_err(hdev, "failed to retrieve chip version\n");
+		if (ret >= 0)
+			ret = -EIO;
+		goto err_hid_close;
+	}
+
+	hid_info(hdev, "chip code: %02x%02x %02x%02x\n",
+		 version.chip_code[0], version.chip_code[1],
+		 version.chip_code[2], version.chip_code[3]);
+
+	ret = ft260_is_interface_enabled(hdev);
+	if (ret <= 0)
+		goto err_hid_close;
+
+	hid_set_drvdata(hdev, dev);
+	dev->hdev = hdev;
+	dev->adap.owner = THIS_MODULE;
+	dev->adap.class = I2C_CLASS_HWMON;
+	dev->adap.algo = &ft260_i2c_algo;
+	dev->adap.quirks = &ft260_i2c_quirks;
+	dev->adap.dev.parent = &hdev->dev;
+	snprintf(dev->adap.name, sizeof(dev->adap.name),
+		 "FT260 usb-i2c bridge on hidraw%d",
+		 ((struct hidraw *)hdev->hidraw)->minor);
+
+	mutex_init(&dev->lock);
+	init_completion(&dev->wait);
+
+	ret = i2c_add_adapter(&dev->adap);
+	if (ret) {
+		hid_err(hdev, "failed to add i2c adapter\n");
+		goto err_hid_close;
+	}
+
+	i2c_set_adapdata(&dev->adap, dev);
+
+	ret = sysfs_create_group(&hdev->dev.kobj, &ft260_attr_group);
+	if (ret < 0) {
+		hid_err(hdev, "failed to create sysfs attrs\n");
+		goto err_i2c_free;
+	}
+
+	ret = ft260_xfer_status(dev);
+	if (ret)
+		ft260_i2c_reset(hdev);
+
+	return 0;
+
+err_i2c_free:
+	i2c_del_adapter(&dev->adap);
+err_hid_close:
+	hid_hw_close(hdev);
+err_hid_stop:
+	hid_hw_stop(hdev);
+	return ret;
+}
+
+static void ft260_remove(struct hid_device *hdev)
+{
+	int ret;
+	struct ft260_device *dev = hid_get_drvdata(hdev);
+
+	ret = ft260_is_interface_enabled(hdev);
+	if (ret <= 0)
+		return;
+
+	sysfs_remove_group(&hdev->dev.kobj, &ft260_attr_group);
+	i2c_del_adapter(&dev->adap);
+
+	hid_hw_close(hdev);
+	hid_hw_stop(hdev);
+}
+
+static int ft260_raw_event(struct hid_device *hdev, struct hid_report *report,
+			   u8 *data, int size)
+{
+	struct ft260_device *dev = hid_get_drvdata(hdev);
+	struct ft260_i2c_input_report *xfer = (void *)data;
+
+	if (xfer->report >= FT260_I2C_REPORT_MIN &&
+	    xfer->report <= FT260_I2C_REPORT_MAX) {
+		ft260_dbg("i2c resp: rep %#02x len %d\n", xfer->report,
+			  xfer->length);
+
+		memcpy(&dev->read_buf[dev->read_idx], &xfer->data,
+		       xfer->length);
+		dev->read_idx += xfer->length;
+
+		if (dev->read_idx == dev->read_len)
+			complete(&dev->wait);
+
+	} else {
+		hid_err(hdev, "unknown report: %#02x\n", xfer->report);
+		return 0;
+	}
+	return 1;
+}
+
+static struct hid_driver ft260_driver = {
+	.name		= "ft260",
+	.id_table	= ft260_devices,
+	.probe		= ft260_probe,
+	.remove		= ft260_remove,
+	.raw_event	= ft260_raw_event,
+};
+
+module_hid_driver(ft260_driver);
+MODULE_DESCRIPTION("FTDI FT260 USB HID to I2C host bridge");
+MODULE_AUTHOR("Michael Zaidman <michael.zaidman@gmail.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h
index e42aaae3138f..daa4c0318cbc 100644
--- a/drivers/hid/hid-ids.h
+++ b/drivers/hid/hid-ids.h
@@ -430,6 +430,7 @@ 
 
 #define USB_VENDOR_ID_FUTURE_TECHNOLOGY	0x0403
 #define USB_DEVICE_ID_RETRODE2		0x97c1
+#define USB_DEVICE_ID_FT260             0x6030
 
 #define USB_VENDOR_ID_ESSENTIAL_REALITY	0x0d7f
 #define USB_DEVICE_ID_ESSENTIAL_REALITY_P5 0x0100