diff mbox series

[v4,1/2] dt-bindings: input: microchip,cap11xx: add advanced sensitivity settings

Message ID 20230627065316.1065911-2-jiriv@axis.com (mailing list archive)
State New, archived
Headers show
Series Input: cap11xx add advanced sensitivity settings | expand

Commit Message

Jiri Valek - 2N June 27, 2023, 6:53 a.m. UTC
Add support for advanced sensitivity settings and signal guard feature.

Signed-off-by: Jiri Valek - 2N <jiriv@axis.com>
---
 .../bindings/input/microchip,cap11xx.yaml     | 77 +++++++++++++++++--
 1 file changed, 72 insertions(+), 5 deletions(-)

Comments

Rob Herring June 29, 2023, 3:16 p.m. UTC | #1
On Tue, Jun 27, 2023 at 08:53:15AM +0200, Jiri Valek - 2N wrote:
> Add support for advanced sensitivity settings and signal guard feature.
> 
> Signed-off-by: Jiri Valek - 2N <jiriv@axis.com>
> ---
>  .../bindings/input/microchip,cap11xx.yaml     | 77 +++++++++++++++++--
>  1 file changed, 72 insertions(+), 5 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
> index 5fa625b5c5fb..b69dac1fba0e 100644
> --- a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
> +++ b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
> @@ -45,13 +45,13 @@ properties:
>        Enables the Linux input system's autorepeat feature on the input device.
>  
>    linux,keycodes:
> -    minItems: 6
> -    maxItems: 6
> +    minItems: 3
> +    maxItems: 8
>      description: |
>        Specifies an array of numeric keycode values to
>        be used for the channels. If this property is
>        omitted, KEY_A, KEY_B, etc are used as defaults.
> -      The array must have exactly six entries.
> +      The number of entries must correspond to the number of channels.

This change seems unrelated? Or maybe advanced sensitivity means more 
channels? If so, explain this in the commit msg.

>  
>    microchip,sensor-gain:
>      $ref: /schemas/types.yaml#/definitions/uint32
> @@ -70,6 +70,55 @@ properties:
>        open drain. This property allows using the active
>        high push-pull output.
>  
> +  microchip,sensitivity-delta-sense:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    default: 32
> +    enum: [1, 2, 4, 8, 16, 32, 64, 128]
> +    description:
> +      Optional parameter. Controls the sensitivity multiplier of a touch detection.
> +      At the more sensitive settings, touches are detected for a smaller delta
> +      capacitance corresponding to a “lighter” touch.
> +
> +  microchip,signal-guard:
> +    $ref: /schemas/types.yaml#/definitions/uint32-array
> +    minItems: 3
> +    maxItems: 8
> +    items:
> +      minimum: 0
> +      maximum: 1
> +    description: |
> +      Optional parameter supported only for CAP129x.
> +      0 - off
> +      1 - on
> +      The signal guard isolates the signal from virtual grounds.
> +      If enabled then the behavior of the channel is changed to signal guard.
> +      The number of entries must correspond to the number of channels.
> +
> +  microchip,input-treshold:
> +    $ref: /schemas/types.yaml#/definitions/uint32-array
> +    minItems: 3
> +    maxItems: 8
> +    items:
> +      minimum: 0
> +      maximum: 127
> +    description:
> +      Optional parameter. Specifies the delta threshold that is used to
> +      determine if a touch has been detected.
> +      The number of entries must correspond to the number of channels.
> +
> +  microchip,calib-sensitivity:
> +    $ref: /schemas/types.yaml#/definitions/uint32-array
> +    minItems: 3
> +    maxItems: 8
> +    items:
> +      minimum: 1
> +      maximum: 4
> +    description:
> +      Optional parameter supported only for CAP129x. Specifies an array of
> +      numeric values that controls the gain used by the calibration routine to
> +      enable sensor inputs to be more sensitive for proximity detection.
> +      The number of entries must correspond to the number of channels.
> +
>  patternProperties:
>    "^led@[0-7]$":
>      type: object
> @@ -98,10 +147,23 @@ allOf:
>          compatible:
>            contains:
>              enum:
> -              - microchip,cap1106
> +              - microchip,cap1188
>      then:
>        patternProperties:
> -        "^led@[0-7]$": false
> +        "^led@[0-7]$": true
> +
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - microchip,cap1293
> +              - microchip,cap1298
> +
> +    then:
> +      properties:
> +        microchip,signal-guard: true
> +        microchip,calib-sensitivity: true

This 'if' doesn't do anything. These properties are already allowed. You 
need an if for the cases they aren't allowed.

>  
>  required:
>    - compatible
> @@ -122,6 +184,11 @@ examples:
>          reg = <0x28>;
>          autorepeat;
>          microchip,sensor-gain = <2>;
> +        microchip,sensitivity-delta-sense = <16>;
> +
> +        microchip,signal-guard = <0>, <0>, <0>, <0>, <0>, <0>;
> +        microchip,input-treshold = <21>, <18>, <46>, <46>, <46>, <21>;
> +        microchip,calib-sensitivity = <1>, <2>, <2>, <1>, <1>, <2>;
>  
>          linux,keycodes = <103>,	/* KEY_UP */
>                           <106>,	/* KEY_RIGHT */
> -- 
> 2.25.1
>
Jiri Valek - 2N July 11, 2023, 1:22 p.m. UTC | #2
On 6/29/23 17:16, Rob Herring wrote:
> On Tue, Jun 27, 2023 at 08:53:15AM +0200, Jiri Valek - 2N wrote:
>> Add support for advanced sensitivity settings and signal guard feature.
>>
>> Signed-off-by: Jiri Valek - 2N <jiriv@axis.com>
>> ---
>>  .../bindings/input/microchip,cap11xx.yaml     | 77 +++++++++++++++++--
>>  1 file changed, 72 insertions(+), 5 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
>> index 5fa625b5c5fb..b69dac1fba0e 100644
>> --- a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
>> +++ b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
>> @@ -45,13 +45,13 @@ properties:
>>        Enables the Linux input system's autorepeat feature on the input device.
>>  
>>    linux,keycodes:
>> -    minItems: 6
>> -    maxItems: 6
>> +    minItems: 3
>> +    maxItems: 8
>>      description: |
>>        Specifies an array of numeric keycode values to
>>        be used for the channels. If this property is
>>        omitted, KEY_A, KEY_B, etc are used as defaults.
>> -      The array must have exactly six entries.
>> +      The number of entries must correspond to the number of channels.
> 
> This change seems unrelated? Or maybe advanced sensitivity means more 
> channels? If so, explain this in the commit msg.

This driver is already used for more CAPxxxx types.
The smallest have only 3 inputs and the biggest one have 8 inputs.
So keycode definition array length can be from 3 to 8 items long.

> 
>>  
>>    microchip,sensor-gain:
>>      $ref: /schemas/types.yaml#/definitions/uint32
>> @@ -70,6 +70,55 @@ properties:
>>        open drain. This property allows using the active
>>        high push-pull output.
>>  
>> +  microchip,sensitivity-delta-sense:
>> +    $ref: /schemas/types.yaml#/definitions/uint32
>> +    default: 32
>> +    enum: [1, 2, 4, 8, 16, 32, 64, 128]
>> +    description:
>> +      Optional parameter. Controls the sensitivity multiplier of a touch detection.
>> +      At the more sensitive settings, touches are detected for a smaller delta
>> +      capacitance corresponding to a “lighter” touch.
>> +
>> +  microchip,signal-guard:
>> +    $ref: /schemas/types.yaml#/definitions/uint32-array
>> +    minItems: 3
>> +    maxItems: 8
>> +    items:
>> +      minimum: 0
>> +      maximum: 1
>> +    description: |
>> +      Optional parameter supported only for CAP129x.
>> +      0 - off
>> +      1 - on
>> +      The signal guard isolates the signal from virtual grounds.
>> +      If enabled then the behavior of the channel is changed to signal guard.
>> +      The number of entries must correspond to the number of channels.
>> +
>> +  microchip,input-treshold:
>> +    $ref: /schemas/types.yaml#/definitions/uint32-array
>> +    minItems: 3
>> +    maxItems: 8
>> +    items:
>> +      minimum: 0
>> +      maximum: 127
>> +    description:
>> +      Optional parameter. Specifies the delta threshold that is used to
>> +      determine if a touch has been detected.
>> +      The number of entries must correspond to the number of channels.
>> +
>> +  microchip,calib-sensitivity:
>> +    $ref: /schemas/types.yaml#/definitions/uint32-array
>> +    minItems: 3
>> +    maxItems: 8
>> +    items:
>> +      minimum: 1
>> +      maximum: 4
>> +    description:
>> +      Optional parameter supported only for CAP129x. Specifies an array of
>> +      numeric values that controls the gain used by the calibration routine to
>> +      enable sensor inputs to be more sensitive for proximity detection.
>> +      The number of entries must correspond to the number of channels.
>> +
>>  patternProperties:
>>    "^led@[0-7]$":
>>      type: object
>> @@ -98,10 +147,23 @@ allOf:
>>          compatible:
>>            contains:
>>              enum:
>> -              - microchip,cap1106
>> +              - microchip,cap1188
>>      then:
>>        patternProperties:
>> -        "^led@[0-7]$": false
>> +        "^led@[0-7]$": true
>> +
>> +  - if:
>> +      properties:
>> +        compatible:
>> +          contains:
>> +            enum:
>> +              - microchip,cap1293
>> +              - microchip,cap1298
>> +
>> +    then:
>> +      properties:
>> +        microchip,signal-guard: true
>> +        microchip,calib-sensitivity: true
> 
> This 'if' doesn't do anything. These properties are already allowed. You 
> need an if for the cases they aren't allowed.

Oh, thanks for the explanation. I will fix it.

> 
>>  
>>  required:
>>    - compatible
>> @@ -122,6 +184,11 @@ examples:
>>          reg = <0x28>;
>>          autorepeat;
>>          microchip,sensor-gain = <2>;
>> +        microchip,sensitivity-delta-sense = <16>;
>> +
>> +        microchip,signal-guard = <0>, <0>, <0>, <0>, <0>, <0>;
>> +        microchip,input-treshold = <21>, <18>, <46>, <46>, <46>, <21>;
>> +        microchip,calib-sensitivity = <1>, <2>, <2>, <1>, <1>, <2>;
>>  
>>          linux,keycodes = <103>,	/* KEY_UP */
>>                           <106>,	/* KEY_RIGHT */
>> -- 
>> 2.25.1
>>

BR
Jiri
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
index 5fa625b5c5fb..b69dac1fba0e 100644
--- a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
+++ b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
@@ -45,13 +45,13 @@  properties:
       Enables the Linux input system's autorepeat feature on the input device.
 
   linux,keycodes:
-    minItems: 6
-    maxItems: 6
+    minItems: 3
+    maxItems: 8
     description: |
       Specifies an array of numeric keycode values to
       be used for the channels. If this property is
       omitted, KEY_A, KEY_B, etc are used as defaults.
-      The array must have exactly six entries.
+      The number of entries must correspond to the number of channels.
 
   microchip,sensor-gain:
     $ref: /schemas/types.yaml#/definitions/uint32
@@ -70,6 +70,55 @@  properties:
       open drain. This property allows using the active
       high push-pull output.
 
+  microchip,sensitivity-delta-sense:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 32
+    enum: [1, 2, 4, 8, 16, 32, 64, 128]
+    description:
+      Optional parameter. Controls the sensitivity multiplier of a touch detection.
+      At the more sensitive settings, touches are detected for a smaller delta
+      capacitance corresponding to a “lighter” touch.
+
+  microchip,signal-guard:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 3
+    maxItems: 8
+    items:
+      minimum: 0
+      maximum: 1
+    description: |
+      Optional parameter supported only for CAP129x.
+      0 - off
+      1 - on
+      The signal guard isolates the signal from virtual grounds.
+      If enabled then the behavior of the channel is changed to signal guard.
+      The number of entries must correspond to the number of channels.
+
+  microchip,input-treshold:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 3
+    maxItems: 8
+    items:
+      minimum: 0
+      maximum: 127
+    description:
+      Optional parameter. Specifies the delta threshold that is used to
+      determine if a touch has been detected.
+      The number of entries must correspond to the number of channels.
+
+  microchip,calib-sensitivity:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 3
+    maxItems: 8
+    items:
+      minimum: 1
+      maximum: 4
+    description:
+      Optional parameter supported only for CAP129x. Specifies an array of
+      numeric values that controls the gain used by the calibration routine to
+      enable sensor inputs to be more sensitive for proximity detection.
+      The number of entries must correspond to the number of channels.
+
 patternProperties:
   "^led@[0-7]$":
     type: object
@@ -98,10 +147,23 @@  allOf:
         compatible:
           contains:
             enum:
-              - microchip,cap1106
+              - microchip,cap1188
     then:
       patternProperties:
-        "^led@[0-7]$": false
+        "^led@[0-7]$": true
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - microchip,cap1293
+              - microchip,cap1298
+
+    then:
+      properties:
+        microchip,signal-guard: true
+        microchip,calib-sensitivity: true
 
 required:
   - compatible
@@ -122,6 +184,11 @@  examples:
         reg = <0x28>;
         autorepeat;
         microchip,sensor-gain = <2>;
+        microchip,sensitivity-delta-sense = <16>;
+
+        microchip,signal-guard = <0>, <0>, <0>, <0>, <0>, <0>;
+        microchip,input-treshold = <21>, <18>, <46>, <46>, <46>, <21>;
+        microchip,calib-sensitivity = <1>, <2>, <2>, <1>, <1>, <2>;
 
         linux,keycodes = <103>,	/* KEY_UP */
                          <106>,	/* KEY_RIGHT */