[2/4] Input: zforce - swap reset and interrupt GPIO

On 25.07.2015 07:19, Dirk Behme wrote:
> On 24.07.2015 23:32, Dmitry Torokhov wrote:
>> On Mon, Jul 20, 2015 at 02:56:35PM +0200, Dirk Behme wrote:
>>> From: Dirk Behme <dirk.behme@gmail.com>
>>>
>>> Swap the order of the reset and interrupt GPIO. This is the preparation
>>> to make the interrupt GPIO optional.
>>>
>>> Note that this needs the same change in the device tree. But as mainline
>>> doesn't contain any zforce device tree entries, nothing has to be done
>>> for us, here.
>>>
>>> All non-mainline device trees have to be adapted, though.
>>
>> No, we can not do that.
>
>
> The proposal to make the interrupt GPIO optional and not completely drop
> it came from you. Any other proposal how you like to get this
> implemented? With completely dropping the interrupt GPIO we would avoid
> this.
>
>
>> We will have to switch to using named gpios
>> (probably call then attn-gpio and reset-gpio respectively and
>> handle old-style DTSes with unnamed 2-entry gpios list).
>
>
> Just to understand correctly: You want the driver to support two GPIOs
> DT styles? One with unnamed 2-entry gpios list, where the interrupt GPIO
> can't be optional, and one with two named GPIOs, where the attn-gpio can
> be optional?


Are you talking about anything like below [1] ?


Best regards

Dirk

[1]

Subject: [PATCH] Input: zforce - make the interrupt GPIO optional

Add support for hardware which uses an I2C Serializer / Deserializer
(SerDes) to communicate with the zFroce touch driver. In this case the
SerDes will be configured as an interrupt controller and the zForce driver
will have no access to poll the GPIO line.

To support this, we add two dedicated new GPIOs in the device tree:
rst-gpio and int-gpio. With the int-gpio being optional, then.

To not break the existing device trees, the index based 'gpios' entries
are still supported, but marked as depreciated.

With this, if the interrupt GPIO is available, either via the old or new
device tree style, the while loop will read and handle the packets as long
as the GPIO indicates that the interrupt is asserted (existing, unchanged
driver behavior).

If the interrupt GPIO isn't available, i.e. not configured via the new
device tree stlye, we are falling back to one read per ISR invocation
(new behavior to support the SerDes).

Note that the gpiod functions help to handle the optional GPIO:
devm_gpiod_get_index_optional() will return NULL in case the interrupt
GPIO isn't available. And gpiod_get_value_cansleep() does cover this, too,
by returning 0 in this case.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
---
  .../bindings/input/touchscreen/zforce_ts.txt       | 15 ++++++--
  drivers/input/touchscreen/zforce_ts.c              | 42 
+++++++++++++++++++++-
  2 files changed, 53 insertions(+), 4 deletions(-)

  	 * When still suspended, return.
@@ -510,7 +511,18 @@ static irqreturn_t zforce_irq_thread(int irq, void 
*dev_id)
  	if (!ts->suspending && device_may_wakeup(&client->dev))
  		pm_stay_awake(&client->dev);

-	while (gpiod_get_value_cansleep(ts->gpio_int)) {
+	while (run) {
+		/*
+		 * Exit the loop if either
+		 * - the optional interrupt GPIO isn't specified
+		 *   (there is only one packet read per ISR invocation, then)
+		 * or
+		 * - the GPIO isn't active any more
+		 *   (packet read until the level GPIO indicates that there is
+		 *    no IRQ any more)
+		 */
+		run = gpiod_get_value_cansleep(ts->gpio_int);
+
  		ret = zforce_read_packet(ts, payload_buffer);
  		if (ret < 0) {
  			dev_err(&client->dev,
@@ -754,6 +766,33 @@ static int zforce_probe(struct i2c_client *client,
  	if (!ts)
  		return -ENOMEM;

+	/*
+	 * The reset GPIO isn't optional, but we might get it
+	 * via the old style DT entries below, too. So it's
+	 * not an error if we don't get it here. Therefore use
+	 * devm_gpiod_get_optional() here.
+	 */
+	ts->gpio_rst = devm_gpiod_get_optional(&client->dev, "rst",
+					       GPIOD_OUT_HIGH);
+	if (IS_ERR(ts->gpio_rst)) {
+		ret = PTR_ERR(ts->gpio_rst);
+		dev_err(&client->dev,
+			"failed to request reset GPIO: %d\n", ret);
+		return ret;
+	}
+
+	ts->gpio_int = devm_gpiod_get_optional(&client->dev, "int", GPIOD_IN);
+	if (IS_ERR(ts->gpio_int)) {
+		ret = PTR_ERR(ts->gpio_int);
+		dev_err(&client->dev,
+			"failed to request interrupt GPIO: %d\n", ret);
+		return ret;
+	}
+
+	/* Skip the old style GPIO if we have the new one */
+	if (ts->gpio_rst)
+		goto skip;
+
  	/* INT GPIO */
  	ts->gpio_int = devm_gpiod_get_index(&client->dev, NULL, 0, GPIOD_IN);
  	if (IS_ERR(ts->gpio_int)) {
@@ -773,6 +812,7 @@ static int zforce_probe(struct i2c_client *client,
  		return ret;
  	}

+skip:
  	ts->reg_vdd = devm_regulator_get_optional(&client->dev, "vdd");
  	if (IS_ERR(ts->reg_vdd)) {
  		ret = PTR_ERR(ts->reg_vdd);



--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[2/4] Input: zforce - swap reset and interrupt GPIO

Commit Message

Comments

Patch