@@ -18,7 +18,7 @@ This document describes the Linux kernel Makefiles.
--- 3.7 Compilation flags
--- 3.8 <deleted>
--- 3.9 Dependency tracking
- --- 3.10 Special Rules
+ --- 3.10 Custom Rules
--- 3.11 $(CC) support functions
--- 3.12 $(LD) support functions
--- 3.13 Script Invocation
@@ -46,7 +46,7 @@ This document describes the Linux kernel Makefiles.
--- 7.5 Architecture-specific boot images
--- 7.6 Building non-kbuild targets
--- 7.7 Commands useful for building a boot image
- --- 7.8 Custom kbuild commands
+ --- 7.8 <deleted>
--- 7.9 Preprocessing linker scripts
--- 7.10 Generic header files
--- 7.11 Post-link pass
@@ -422,21 +422,21 @@ more details, with real examples.
Thus, if you change an option to $(CC) all affected files will
be re-compiled.
-3.10 Special Rules
+3.10 Custom Rules
------------------
- Special rules are used when the kbuild infrastructure does
+ Custom rules are used when the kbuild infrastructure does
not provide the required support. A typical example is
header files generated during the build process.
Another example are the architecture-specific Makefiles which
- need special rules to prepare boot images etc.
+ need custom rules to prepare boot images etc.
- Special rules are written as normal Make rules.
+ Custom rules are written as normal Make rules.
Kbuild is not executing in the directory where the Makefile is
- located, so all special rules shall provide a relative
+ located, so all custom rules shall use a relative
path to prerequisite files and target files.
- Two variables are used when defining special rules:
+ Two variables are used when defining custom rules:
$(src)
$(src) is a relative path which points to the directory
@@ -454,7 +454,7 @@ more details, with real examples.
$(obj)/53c8xx_d.h: $(src)/53c7,8xx.scr $(src)/script_asm.pl
$(CPP) -DCHIP=810 - < $< | ... $(src)/script_asm.pl
- This is a special rule, following the normal syntax
+ This is a custom rule, following the normal syntax
required by make.
The target file depends on two prerequisite files. References
@@ -471,11 +471,33 @@ more details, with real examples.
Example::
- #arch/blackfin/boot/Makefile
- $(obj)/vmImage: $(obj)/vmlinux.gz
- $(call if_changed,uimage)
- @$(kecho) 'Kernel: $@ is ready'
+ # arch/arm/Makefile
+ $(BOOT_TARGETS): vmlinux
+ $(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $(boot)/$@
+ @$(kecho) ' Kernel: $(boot)/$@ is ready'
+ When kbuild is executing with KBUILD_VERBOSE=0, then only a shorthand
+ of a command is normally displayed.
+ To enable this behaviour for custom commands kbuild requires
+ two variables to be set::
+
+ quiet_cmd_<command> - what shall be echoed
+ cmd_<command> - the command to execute
+
+ Example::
+
+ # lib/Makefile
+ quiet_cmd_crc32 = GEN $@
+ cmd_crc32 = $< > $@
+
+ $(obj)/crc32table.h: $(obj)/gen_crc32table
+ $(call cmd,crc32)
+
+ When updating the $(obj)/crc32table.h target, the line:
+
+ GEN lib/crc32table.h
+
+ will be displayed with "make KBUILD_VERBOSE=0".
3.11 $(CC) support functions
----------------------------
@@ -744,7 +766,7 @@ Both possibilities are described in the following.
as a prerequisite.
This is possible in two ways:
- (1) List the prerequisite explicitly in a special rule.
+ (1) List the prerequisite explicitly in a custom rule.
Example::
@@ -755,11 +777,11 @@ Both possibilities are described in the following.
The target $(obj)/devlist.h will not be built before
$(obj)/gen-devlist is updated. Note that references to
- the host programs in special rules must be prefixed with $(obj).
+ the host programs in custom rules must be prefixed with $(obj).
(2) Use always-y
- When there is no suitable special rule, and the host program
+ When there is no suitable custom rule, and the host program
shall be built when a makefile is entered, the always-y
variable shall be used.
@@ -1281,8 +1303,8 @@ When kbuild executes, the following steps are followed (roughly):
otherwise the command line check will fail, and the target will
always be built.
Assignments to $(targets) are without $(obj)/ prefix.
- if_changed may be used in conjunction with custom commands as
- defined in 7.8 "Custom kbuild commands".
+ if_changed may be used in conjunction with custom rules as
+ defined in "3.10 Custom Rules".
Note: It is a typical mistake to forget the FORCE prerequisite.
Another common pitfall is that whitespace is sometimes
@@ -1362,36 +1384,6 @@ When kbuild executes, the following steps are followed (roughly):
targets += $(dtb-y)
DTC_FLAGS ?= -p 1024
-7.8 Custom kbuild commands
---------------------------
-
- When kbuild is executing with KBUILD_VERBOSE=0, then only a shorthand
- of a command is normally displayed.
- To enable this behaviour for custom commands kbuild requires
- two variables to be set::
-
- quiet_cmd_<command> - what shall be echoed
- cmd_<command> - the command to execute
-
- Example::
-
- #
- quiet_cmd_image = BUILD $@
- cmd_image = $(obj)/tools/build $(BUILDFLAGS) \
- $(obj)/vmlinux.bin > $@
-
- targets += bzImage
- $(obj)/bzImage: $(obj)/vmlinux.bin $(obj)/tools/build FORCE
- $(call if_changed,image)
- @echo 'Kernel: $@ is ready'
-
- When updating the $(obj)/bzImage target, the line:
-
- BUILD arch/x86/boot/bzImage
-
- will be displayed with "make KBUILD_VERBOSE=0".
-
-
7.9 Preprocessing linker scripts
--------------------------------
The two sections "3.10 Special Rules" and "7.8 Custom kbuild commands" are related because you must understand both of them when you write custom rules. Actually I do not understand the policy about what to go into "3 The kbuild files" and what into "7 Architecture Makefile". This commit reworks the custom rule explanation as follows: - Merged "7.8 Custom kbuild commands" into "3.10 Special Rules". - Reword "Special Rules" to "Custom Rules" for consistency. - Update the example for kecho because the blackfin Makefile does not exist any more. - Replace the example for cmd_<command> with a simpler one. Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> --- Documentation/kbuild/makefiles.rst | 88 ++++++++++++++---------------- 1 file changed, 40 insertions(+), 48 deletions(-)