diff mbox series

[v2,02/10] ARM: dts: ls1021a: add TQ-Systems MBLS102xA device tree

Message ID 20230120133455.3962413-3-alexander.stein@ew.tq-group.com (mailing list archive)
State New, archived
Headers show
Series TQMLS1021A support | expand

Commit Message

Alexander Stein Jan. 20, 2023, 1:34 p.m. UTC 
Add device tree for the MBLS102xA mainboard with TQMLS1021A SoM.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v2:
* Remove unnecessary status = "okay"
* Remove underscore from node names
* Move reg direct below compatiblefor i2c devices
* Remove i2c device nodes without software support
  Add a comment about existance for the device though

 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/ls1021a-tqmls1021a-mbls1021a.dts | 406 ++++++++++++++++++
 arch/arm/boot/dts/ls1021a-tqmls1021a.dtsi     |  81 ++++
 3 files changed, 488 insertions(+)
 create mode 100644 arch/arm/boot/dts/ls1021a-tqmls1021a-mbls1021a.dts
 create mode 100644 arch/arm/boot/dts/ls1021a-tqmls1021a.dtsi

Comments

Alexander Stein Jan. 26, 2023, 1:50 p.m. UTC | #1 
Hi Shawn,

thanks for your feedback.

Am Donnerstag, 26. Januar 2023, 10:44:21 CET schrieb Shawn Guo:
> On Fri, Jan 20, 2023 at 02:34:47PM +0100, Alexander Stein wrote:
> > Add device tree for the MBLS102xA mainboard with TQMLS1021A SoM.
> > 
> > Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> > ---
> > Changes in v2:
> > * Remove unnecessary status = "okay"
> > * Remove underscore from node names
> > * Move reg direct below compatiblefor i2c devices
> > * Remove i2c device nodes without software support
> > 
> >   Add a comment about existance for the device though
> >  
> >  arch/arm/boot/dts/Makefile                    |   1 +
> >  .../boot/dts/ls1021a-tqmls1021a-mbls1021a.dts | 406 ++++++++++++++++++
> >  arch/arm/boot/dts/ls1021a-tqmls1021a.dtsi     |  81 ++++
> >  3 files changed, 488 insertions(+)
> >  create mode 100644 arch/arm/boot/dts/ls1021a-tqmls1021a-mbls1021a.dts
> >  create mode 100644 arch/arm/boot/dts/ls1021a-tqmls1021a.dtsi
> > 
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index d0c07867aeabe..44b5ed44b13d6 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -802,6 +802,7 @@ dtb-$(CONFIG_SOC_LS1021A) += \
> > 
> >  	ls1021a-iot.dtb \
> >  	ls1021a-moxa-uc-8410a.dtb \
> >  	ls1021a-qds.dtb \
> > 
> > +	ls1021a-tqmls1021a-mbls1021a.dtb \
> > 
> >  	ls1021a-tsn.dtb \
> >  	ls1021a-twr.dtb
> >  
> >  dtb-$(CONFIG_SOC_VF610) += \
> > 
> > diff --git a/arch/arm/boot/dts/ls1021a-tqmls1021a-mbls1021a.dts
> > b/arch/arm/boot/dts/ls1021a-tqmls1021a-mbls1021a.dts new file mode 100644
> > index 0000000000000..aa8b605344655
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/ls1021a-tqmls1021a-mbls1021a.dts
> > @@ -0,0 +1,406 @@
> > +// SPDX-License-Identifier: (GPL-2.0-or-later OR X11)
> > +/*
> > + * Copyright 2013-2014 Freescale Semiconductor, Inc.
> > + * Copyright 2018-2023 TQ-Systems GmbH <linux@ew.tq-group.com>,
> > + * D-82229 Seefeld, Germany.
> > + * Author: Alexander Stein
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/linux-event-codes.h>
> > +#include <dt-bindings/leds/common.h>
> > +#include <dt-bindings/leds/leds-pca9532.h>
> > +#include <dt-bindings/net/ti-dp83867.h>
> > +#include "ls1021a-tqmls1021a.dtsi"
> > +
> > +/ {
> > +	model = "TQMLS102xA SOM on MBLS102xA";
> > +	compatible = "tq,ls1021a-tqmls1021a-mbls102xa", "tq,ls1021a-
tqmls1021a",
> > "fsl,ls1021a"; +
> > +	audio_mclk: audio-clock {
> > +		compatible = "fixed-clock";
> > +		#clock-cells = <0>;
> > +		clock-frequency = <25000000>;
> > +	};
> > +
> > +	backlight_dcu: backlight {
> > +		compatible = "gpio-backlight";
> > +		gpios = <&pca9530 0 GPIO_ACTIVE_LOW>;
> > +		status = "disabled";
> > +	};
> > +
> > +	gpio-keys {
> > +		compatible = "gpio-keys";
> > +		autorepeat;
> > +
> > +		switch-1 {
> > +			label = "S6";
> > +			linux,code = <BTN_0>;
> > +			gpios = <&pca9554_0 0 GPIO_ACTIVE_LOW>;
> > +		};
> > +
> > +		btn2: switch-2 {
> > +			label = "S7";
> > +			linux,code = <BTN_1>;
> > +			gpios = <&pca9554_0 1 GPIO_ACTIVE_LOW>;
> > +		};
> > +
> > +		switch-3 {
> > +			label = "S8";
> > +			linux,code = <BTN_2>;
> > +			gpios = <&pca9554_0 2 GPIO_ACTIVE_LOW>;
> > +		};
> > +	};
> > +
> > +	gpio_leds: gpio-leds {
> > +		compatible = "gpio-leds";
> > +
> > +		led-0 {
> > +			color = <LED_COLOR_ID_GREEN>;
> > +			function = LED_FUNCTION_STATUS;
> > +			function-enumerator = <0>;
> > +			gpios = <&pca9554_2 4 GPIO_ACTIVE_LOW>;
> > +			linux,default-trigger = "default-on";
> > +		};
> > +
> > +		led-1 {
> > +			color = <LED_COLOR_ID_GREEN>;
> > +			function = LED_FUNCTION_STATUS;
> > +			function-enumerator = <1>;
> > +			gpios = <&pca9554_2 5 GPIO_ACTIVE_LOW>;
> > +			linux,default-trigger = "default-on";
> > +		};
> > +
> > +		led-2 {
> > +			color = <LED_COLOR_ID_GREEN>;
> > +			function = LED_FUNCTION_STATUS;
> > +			function-enumerator = <2>;
> > +			gpios = <&pca9554_2 6 GPIO_ACTIVE_LOW>;
> > +			linux,default-trigger = "default-on";
> > +		};
> > +
> > +		led-3 {
> > +			color = <LED_COLOR_ID_GREEN>;
> > +			function = LED_FUNCTION_HEARTBEAT;
> > +			function-enumerator = <0>;
> > +			gpios = <&pca9554_2 7 GPIO_ACTIVE_LOW>;
> > +			linux,default-trigger = "heartbeat";
> > +		};
> > +	};
> > +
> > +	lvds_encoder: lvds-encoder {
> > +		compatible = "ti,sn75lvds83", "lvds-encoder";
> > +		power-supply = <&reg_3p3v>;
> > +		status = "disabled";
> > +
> > +		ports {
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +
> > +			port@0 {
> > +				reg = <0>;
> > +
> > +				lvds_encoder_in: endpoint {};
> > +			};
> > +
> > +			port@1 {
> > +				reg = <1>;
> > +
> > +				lvds_encoder_out: endpoint {};
> > +			};
> > +		};
> > +	};
> > +
> > +	reg_1p2v: regulator-1p2v {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "1P2V";
> > +		regulator-min-microvolt = <1200000>;
> > +		regulator-max-microvolt = <1200000>;
> > +		regulator-always-on;
> > +		vin-supply = <&reg_3p3v>;
> > +	};
> > +
> > +	reg_3p3v: regulator-3p3v {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "3P3V";
> > +		regulator-min-microvolt = <3300000>;
> > +		regulator-max-microvolt = <3300000>;
> > +		regulator-always-on;
> > +	};
> > +
> > +	hdmi_out: hdmi {
> > +		compatible = "hdmi-connector";
> > +		type = "a";
> > +		ddc-i2c-bus = <&i2c0>;
> > +		status = "disabled";
> > +
> > +		port {
> > +			hdmi_in: endpoint {
> > +				remote-endpoint = <&sii9022a_out>;
> > +			};
> > +		};
> > +	};
> > +
> > +	display: panel {
> > +		backlight = <&backlight_dcu>;
> > +		enable-gpios = <&pca9554_1 3 GPIO_ACTIVE_HIGH>;
> > +		status = "disabled";
> > +
> > +		port {
> > +			panel_in: endpoint {};
> > +		};
> > +	};
> > +
> > +	sound {
> > +		compatible = "fsl,imx-audio-tlv320aic32x4";
> > +		model = "ls1021a-mbls1021a-tlv320aic32";
> > +		ssi-controller = <&sai1>;
> > +		audio-codec = <&tlv320aic32x4>;
> > +	};
> > +
> > +};
> > +
> > +&can0 {
> > +	status = "okay";
> > +	xceiver-supply = <&reg_3p3v>;
> 
> We generally end property list with 'status'.

Thanks, will change it.

> > +};
> > +
> > +&can1 {
> > +	status = "okay";
> > +	xceiver-supply = <&reg_3p3v>;
> > +};
> > +
> > +&dspi0 {
> > +	bus-num = <0>;
> > +	status = "okay";
> > +};
> > +
> > +&enet0 {
> > +	phy-handle = <&rgmii_phy0c>;
> > +	phy-mode = "rgmii-id";
> > +	mac-address = [ 00 00 00 00 00 00 ];
> > +	status = "okay";
> > +};
> > +
> > +&enet1 {
> > +	tbi-handle = <&tbi1>;
> > +	phy-handle = <&sgmii_phy03>;
> > +	phy-mode = "sgmii";
> > +	mac-address = [ 00 00 00 00 00 00 ];
> > +	status = "okay";
> > +};
> > +
> > +&enet2 {
> > +	phy-handle = <&rgmii_phy04>;
> > +	phy-mode = "rgmii-id";
> > +	mac-address = [ 00 00 00 00 00 00 ];
> > +	status = "okay";
> > +};
> > +
> > +&i2c0 {
> > +	status = "okay";
> > +
> > +	tlv320aic32x4: audio-codec@18 {
> > +		compatible = "ti,tlv320aic32x4";
> > +		reg = <0x18>;
> > +		clocks = <&audio_mclk>;
> > +		clock-names = "mclk";
> > +		ldoin-supply = <&reg_3p3v>;
> > +		iov-supply = <&reg_3p3v>;
> > +	};
> > +
> > +	pca9554_0: gpio-expander@20 {
> > +		compatible = "nxp,pca9554";
> > +		reg = <0x20>;
> > +		gpio-controller;
> > +		#gpio-cells = <2>;
> > +		interrupt-parent = <&gpio0>;
> > +		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
> > +		interrupt-controller;
> > +		#interrupt-cells = <2>;
> > +		vcc-supply = <&reg_3p3v>;
> > +		gpio-line-names = "BUTTON0", "BUTTON1",
> > +				  "BUTTON2", "EMMC_SEL",
> > +				  "DIP2", "DIP3",
> > +				  "EXT_TOUCH_INT", "GPIO_1";
> > +	};
> > +
> > +	pca9554_1: gpio-expander@21 {
> > +		compatible = "nxp,pca9554";
> > +		reg = <0x21>;
> > +		gpio-controller;
> > +		#gpio-cells = <2>;
> > +		interrupt-parent = <&gpio0>;
> > +		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> > +		interrupt-controller;
> > +		#interrupt-cells = <2>;
> > +		vcc-supply = <&reg_3p3v>;
> > +		gpio-line-names = "PCIE_PWR_EN", "MPCIE_DISABLE#",
> > +				  "MPCIE_WAKE#", "LCD_BLT_EN",
> > +				  "LCD_PWR_EN", "EC1_PHY_PWDN",
> > +				  "EC3_PHY_PWDN", "SGMII_PHY_PWDN";
> > +	};
> > +
> > +	pca9554_2: gpio-expander@22 {
> > +		compatible = "nxp,pca9554";
> > +		reg = <0x22>;
> > +		gpio-controller;
> > +		#gpio-cells = <2>;
> > +		interrupt-parent = <&extirq>;
> > +		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
> > +		interrupt-controller;
> > +		#interrupt-cells = <2>;
> > +		vcc-supply = <&reg_3p3v>;
> > +		gpio-line-names = "MUX_SEL0", "MUX_SEL1",
> > +				  "MUX_SEL2", "MUX_SEL3",
> > +				  "V95", "V96", "V97", "V98";
> > +	};
> > +
> > +	sii9022a: hdmi-transmitter@3b {
> > +		compatible = "sil,sii9022";
> > +		reg = <0x3b>;
> > +		iovcc-supply = <&reg_3p3v>;
> > +		cvcc12-supply = <&reg_1p2v>;
> > +		interrupts = <GIC_SPI 167 IRQ_TYPE_EDGE_RISING>;
> > +		#sound-dai-cells = <0>;
> > +		sil,i2s-data-lanes = <0>;
> > +		status = "disabled";
> > +
> > +		ports {
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +
> > +			port@0 {
> > +				reg = <0>;
> > +
> > +				sii9022a_in: endpoint {};
> > +			};
> > +
> > +			port@1 {
> > +				reg = <1>;
> > +
> > +				sii9022a_out: endpoint {
> > +					remote-endpoint = 
<&hdmi_in>;
> > +				};
> > +			};
> > +		};
> > +	};
> > +
> > +	stmpe811: touchscreen@41 {
> > +		compatible = "st,stmpe811";
> > +		reg = <0x41>;
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		interrupt-parent = <&gpio0>;
> > +		interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
> > +		vcc-supply = <&reg_3p3v>;
> > +		vio-supply = <&reg_3p3v>;
> > +
> > +		gpio {
> > +			compatible = "st,stmpe-gpio";
> > +			gpio-controller;
> > +			#gpio-cells = <2>;
> > +			/* GPIO 5-7 used for touch */
> > +			st,norequest-mask = <0xf0>;
> > +			gpio-line-names = "GPIO_ADC_I2C1_1",
> > +					  "GPIO_ADC_I2C1_2",
> > +					  "GPIO_ADC_I2C1_3",
> > +					  "GPIO_ADC_I2C1_4";
> > +		};
> > +
> > +		touchscreen {
> > +			compatible = "st,stmpe-ts";
> > +			status = "disabled";
> > +		};
> > +	};
> > +
> > +	pca9530: leds@60 {
> > +		compatible = "nxp,pca9530";
> > +		reg = <0x60>;
> > +		gpio-controller;
> > +		#gpio-cells = <2>;
> > +		gpio-line-names = "PWM_0", "PWM_1";
> > +
> > +		led-0 {
> > +			type = <PCA9532_TYPE_GPIO>;
> > +		};
> > +
> > +		led-1 {
> > +			type = <PCA9532_TYPE_GPIO>;
> > +		};
> > +	};
> > +
> > +};
> > +
> > +&i2c1 {
> > +	status = "okay";
> > +};
> > +
> > +&lpuart0 {
> > +	status = "okay";
> > +	linux,rs485-enabled-at-boot-time;
> > +};
> > +
> > +&mdio0 {
> > +	sgmii_phy03: ethernet-phy@3 {
> > +		compatible = "ethernet-phy-ieee802.3-c22";
> > +		reg = <0x03>;
> > +		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> > +		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
> > +		ti,dp83867-rxctrl-strap-quirk;
> > +	};
> > +
> > +	rgmii_phy04: ethernet-phy@4 {
> > +		compatible = "ethernet-phy-ieee802.3-c22";
> > +		reg = <0x04>;
> > +		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
> > +		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> > +		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> > +		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
> > +	};
> > +
> > +	rgmii_phy0c: ethernet-phy@c {
> > +		compatible = "ethernet-phy-ieee802.3-c22";
> > +		reg = <0x0c>;
> > +		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
> > +		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> > +		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> > +		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
> > +	};
> > +};
> > +
> > +&pwm6 {
> > +	status = "okay";
> > +};
> > +
> > +&pwm7 {
> > +	status = "okay";
> > +};
> > +
> > +&sai1 {
> > +	status = "okay";
> > +};
> > +
> > +&sata {
> > +	/delete-property/ dma-coherent;
> > +	status = "okay";
> > +};
> > +
> > +&uart0 {
> > +	status = "okay";
> > +};
> > +
> > +&uart1 {
> > +	status = "okay";
> > +};
> > +
> > +&usb3 {
> > +	/*
> > +	 * Although DR connector, VBUS is always driven, so
> > +	 * restrict to host mode.
> > +	 */
> > +	dr_mode = "host";
> > +	status = "okay";
> > +};
> > diff --git a/arch/arm/boot/dts/ls1021a-tqmls1021a.dtsi
> > b/arch/arm/boot/dts/ls1021a-tqmls1021a.dtsi new file mode 100644
> > index 0000000000000..24ad4a76fe597
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/ls1021a-tqmls1021a.dtsi
> > @@ -0,0 +1,81 @@
> > +// SPDX-License-Identifier: (GPL-2.0-or-later OR X11)
> > +/*
> > + * Copyright 2013-2014 Freescale Semiconductor, Inc.
> > + * Copyright 2018-2023 TQ-Systems GmbH <linux@ew.tq-group.com>,
> > + * D-82229 Seefeld, Germany.
> > + * Author: Alexander Stein
> > + */
> > +
> > +#include "ls1021a.dtsi"
> > +
> > +/ {
> > +	model = "TQMLS102xA SOM";
> > +	compatible = "tq,ls1021a-tqmls1021a", "fsl,ls1021a";
> > +
> > +	reg_3p3v_som: regulator-3p3v-som {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "3P3V_SOM";
> > +		regulator-min-microvolt = <3300000>;
> > +		regulator-max-microvolt = <3300000>;
> > +		regulator-always-on;
> > +	};
> > +};
> > +
> > +&esdhc {
> > +	compatible = "fsl,esdhc", "fsl,ls1021a-esdhc";
> 
> We usually order compatibles from the specific to the generic.

Thanks, will change it.
I'll will respin this series once the defconfig patches taken by Arnd hit 
linux-next.

Best regards
Alexander

> Shawn
> 
> > +	/* e-MMC over 8 data lines */
> > +	bus-width = <8>;
> > +	status = "okay";
> > +};
> > +
> > +&i2c0 {
> > +	status = "okay";
> > +
> > +	/* MC34VR500 DC/DC regulator at 0x8 */
> > +	/* On-board PMC at 0x11 */
> > +
> > +	sa56004: temperature-sensor@4c {
> > +		compatible = "nxp,sa56004";
> > +		reg = <0x4c>;
> > +		vcc-supply = <&reg_3p3v_som>;
> > +	};
> > +
> > +	rtc0: rtc@51 {
> > +		compatible = "nxp,pcf85063a";
> > +		reg = <0x51>;
> > +		quartz-load-femtofarads = <12500>;
> > +	};
> > +
> > +	m24c64_54: eeprom@54 {
> > +		compatible = "atmel,24c64";
> > +		reg = <0x54>;
> > +		pagesize = <32>;
> > +		read-only;
> > +		vcc-supply = <&reg_3p3v_som>;
> > +	};
> > +};
> > +
> > +&mdio0 {
> > +	tbi1: tbi-phy@8 {
> > +		reg = <0x8>;
> > +		device_type = "tbi-phy";
> > +	};
> > +};
> > +
> > +&scfg {
> > +	reg = <0x0 0x1570000 0x0 0x0e00>;
> > +};
> > +
> > +&qspi {
> > +	status = "okay";
> > +
> > +	qflash0: flash@0 {
> > +		compatible = "jedec,spi-nor";
> > +		#address-cells = <1>;
> > +		#size-cells = <1>;
> > +		spi-max-frequency = <20000000>;
> > +		spi-rx-bus-width = <4>;
> > +		spi-tx-bus-width = <4>;
> > +		reg = <0>;
> > +	};
> > +};
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d0c07867aeabe..44b5ed44b13d6 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -802,6 +802,7 @@  dtb-$(CONFIG_SOC_LS1021A) += \
 	ls1021a-iot.dtb \
 	ls1021a-moxa-uc-8410a.dtb \
 	ls1021a-qds.dtb \
+	ls1021a-tqmls1021a-mbls1021a.dtb \
 	ls1021a-tsn.dtb \
 	ls1021a-twr.dtb
 dtb-$(CONFIG_SOC_VF610) += \
diff --git a/arch/arm/boot/dts/ls1021a-tqmls1021a-mbls1021a.dts b/arch/arm/boot/dts/ls1021a-tqmls1021a-mbls1021a.dts
new file mode 100644
index 0000000000000..aa8b605344655
--- /dev/null
+++ b/arch/arm/boot/dts/ls1021a-tqmls1021a-mbls1021a.dts
@@ -0,0 +1,406 @@ 
+// SPDX-License-Identifier: (GPL-2.0-or-later OR X11)
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ * Copyright 2018-2023 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Alexander Stein
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "ls1021a-tqmls1021a.dtsi"
+
+/ {
+	model = "TQMLS102xA SOM on MBLS102xA";
+	compatible = "tq,ls1021a-tqmls1021a-mbls102xa", "tq,ls1021a-tqmls1021a", "fsl,ls1021a";
+
+	audio_mclk: audio-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	backlight_dcu: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&pca9530 0 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		switch-1 {
+			label = "S6";
+			linux,code = <BTN_0>;
+			gpios = <&pca9554_0 0 GPIO_ACTIVE_LOW>;
+		};
+
+		btn2: switch-2 {
+			label = "S7";
+			linux,code = <BTN_1>;
+			gpios = <&pca9554_0 1 GPIO_ACTIVE_LOW>;
+		};
+
+		switch-3 {
+			label = "S8";
+			linux,code = <BTN_2>;
+			gpios = <&pca9554_0 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio_leds: gpio-leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <0>;
+			gpios = <&pca9554_2 4 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <1>;
+			gpios = <&pca9554_2 5 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <2>;
+			gpios = <&pca9554_2 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-3 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_HEARTBEAT;
+			function-enumerator = <0>;
+			gpios = <&pca9554_2 7 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	lvds_encoder: lvds-encoder {
+		compatible = "ti,sn75lvds83", "lvds-encoder";
+		power-supply = <&reg_3p3v>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_encoder_in: endpoint {};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lvds_encoder_out: endpoint {};
+			};
+		};
+	};
+
+	reg_1p2v: regulator-1p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P2V";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		vin-supply = <&reg_3p3v>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	hdmi_out: hdmi {
+		compatible = "hdmi-connector";
+		type = "a";
+		ddc-i2c-bus = <&i2c0>;
+		status = "disabled";
+
+		port {
+			hdmi_in: endpoint {
+				remote-endpoint = <&sii9022a_out>;
+			};
+		};
+	};
+
+	display: panel {
+		backlight = <&backlight_dcu>;
+		enable-gpios = <&pca9554_1 3 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+
+		port {
+			panel_in: endpoint {};
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-tlv320aic32x4";
+		model = "ls1021a-mbls1021a-tlv320aic32";
+		ssi-controller = <&sai1>;
+		audio-codec = <&tlv320aic32x4>;
+	};
+
+};
+
+&can0 {
+	status = "okay";
+	xceiver-supply = <&reg_3p3v>;
+};
+
+&can1 {
+	status = "okay";
+	xceiver-supply = <&reg_3p3v>;
+};
+
+&dspi0 {
+	bus-num = <0>;
+	status = "okay";
+};
+
+&enet0 {
+	phy-handle = <&rgmii_phy0c>;
+	phy-mode = "rgmii-id";
+	mac-address = [ 00 00 00 00 00 00 ];
+	status = "okay";
+};
+
+&enet1 {
+	tbi-handle = <&tbi1>;
+	phy-handle = <&sgmii_phy03>;
+	phy-mode = "sgmii";
+	mac-address = [ 00 00 00 00 00 00 ];
+	status = "okay";
+};
+
+&enet2 {
+	phy-handle = <&rgmii_phy04>;
+	phy-mode = "rgmii-id";
+	mac-address = [ 00 00 00 00 00 00 ];
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	tlv320aic32x4: audio-codec@18 {
+		compatible = "ti,tlv320aic32x4";
+		reg = <0x18>;
+		clocks = <&audio_mclk>;
+		clock-names = "mclk";
+		ldoin-supply = <&reg_3p3v>;
+		iov-supply = <&reg_3p3v>;
+	};
+
+	pca9554_0: gpio-expander@20 {
+		compatible = "nxp,pca9554";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		vcc-supply = <&reg_3p3v>;
+		gpio-line-names = "BUTTON0", "BUTTON1",
+				  "BUTTON2", "EMMC_SEL",
+				  "DIP2", "DIP3",
+				  "EXT_TOUCH_INT", "GPIO_1";
+	};
+
+	pca9554_1: gpio-expander@21 {
+		compatible = "nxp,pca9554";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		vcc-supply = <&reg_3p3v>;
+		gpio-line-names = "PCIE_PWR_EN", "MPCIE_DISABLE#",
+				  "MPCIE_WAKE#", "LCD_BLT_EN",
+				  "LCD_PWR_EN", "EC1_PHY_PWDN",
+				  "EC3_PHY_PWDN", "SGMII_PHY_PWDN";
+	};
+
+	pca9554_2: gpio-expander@22 {
+		compatible = "nxp,pca9554";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&extirq>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		vcc-supply = <&reg_3p3v>;
+		gpio-line-names = "MUX_SEL0", "MUX_SEL1",
+				  "MUX_SEL2", "MUX_SEL3",
+				  "V95", "V96", "V97", "V98";
+	};
+
+	sii9022a: hdmi-transmitter@3b {
+		compatible = "sil,sii9022";
+		reg = <0x3b>;
+		iovcc-supply = <&reg_3p3v>;
+		cvcc12-supply = <&reg_1p2v>;
+		interrupts = <GIC_SPI 167 IRQ_TYPE_EDGE_RISING>;
+		#sound-dai-cells = <0>;
+		sil,i2s-data-lanes = <0>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sii9022a_in: endpoint {};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				sii9022a_out: endpoint {
+					remote-endpoint = <&hdmi_in>;
+				};
+			};
+		};
+	};
+
+	stmpe811: touchscreen@41 {
+		compatible = "st,stmpe811";
+		reg = <0x41>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+		vcc-supply = <&reg_3p3v>;
+		vio-supply = <&reg_3p3v>;
+
+		gpio {
+			compatible = "st,stmpe-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			/* GPIO 5-7 used for touch */
+			st,norequest-mask = <0xf0>;
+			gpio-line-names = "GPIO_ADC_I2C1_1",
+					  "GPIO_ADC_I2C1_2",
+					  "GPIO_ADC_I2C1_3",
+					  "GPIO_ADC_I2C1_4";
+		};
+
+		touchscreen {
+			compatible = "st,stmpe-ts";
+			status = "disabled";
+		};
+	};
+
+	pca9530: leds@60 {
+		compatible = "nxp,pca9530";
+		reg = <0x60>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "PWM_0", "PWM_1";
+
+		led-0 {
+			type = <PCA9532_TYPE_GPIO>;
+		};
+
+		led-1 {
+			type = <PCA9532_TYPE_GPIO>;
+		};
+	};
+
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&lpuart0 {
+	status = "okay";
+	linux,rs485-enabled-at-boot-time;
+};
+
+&mdio0 {
+	sgmii_phy03: ethernet-phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x03>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+
+	rgmii_phy04: ethernet-phy@4 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x04>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+	};
+
+	rgmii_phy0c: ethernet-phy@c {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0c>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+	};
+};
+
+&pwm6 {
+	status = "okay";
+};
+
+&pwm7 {
+	status = "okay";
+};
+
+&sai1 {
+	status = "okay";
+};
+
+&sata {
+	/delete-property/ dma-coherent;
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb3 {
+	/*
+	 * Although DR connector, VBUS is always driven, so
+	 * restrict to host mode.
+	 */
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/ls1021a-tqmls1021a.dtsi b/arch/arm/boot/dts/ls1021a-tqmls1021a.dtsi
new file mode 100644
index 0000000000000..24ad4a76fe597
--- /dev/null
+++ b/arch/arm/boot/dts/ls1021a-tqmls1021a.dtsi
@@ -0,0 +1,81 @@ 
+// SPDX-License-Identifier: (GPL-2.0-or-later OR X11)
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ * Copyright 2018-2023 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Alexander Stein
+ */
+
+#include "ls1021a.dtsi"
+
+/ {
+	model = "TQMLS102xA SOM";
+	compatible = "tq,ls1021a-tqmls1021a", "fsl,ls1021a";
+
+	reg_3p3v_som: regulator-3p3v-som {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V_SOM";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&esdhc {
+	compatible = "fsl,esdhc", "fsl,ls1021a-esdhc";
+	/* e-MMC over 8 data lines */
+	bus-width = <8>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	/* MC34VR500 DC/DC regulator at 0x8 */
+	/* On-board PMC at 0x11 */
+
+	sa56004: temperature-sensor@4c {
+		compatible = "nxp,sa56004";
+		reg = <0x4c>;
+		vcc-supply = <&reg_3p3v_som>;
+	};
+
+	rtc0: rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+		quartz-load-femtofarads = <12500>;
+	};
+
+	m24c64_54: eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+		pagesize = <32>;
+		read-only;
+		vcc-supply = <&reg_3p3v_som>;
+	};
+};
+
+&mdio0 {
+	tbi1: tbi-phy@8 {
+		reg = <0x8>;
+		device_type = "tbi-phy";
+	};
+};
+
+&scfg {
+	reg = <0x0 0x1570000 0x0 0x0e00>;
+};
+
+&qspi {
+	status = "okay";
+
+	qflash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <20000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+		reg = <0>;
+	};
+};