@@ -11,6 +11,7 @@ TEST_PROGS = \
hw_stats_l3_gre.sh \
loopback.sh \
nic_link_layer.py \
+ nic_performance.py \
pp_alloc_fail.py \
rss_ctx.py \
#
new file mode 100644
@@ -0,0 +1,121 @@
+#!/usr/bin/env python3
+# SPDX-License-Identifier: GPL-2.0
+
+#Introduction:
+#This file has basic performance test for generic NIC drivers.
+#The test comprises of throughput check for TCP and UDP streams.
+#
+#Setup:
+#Connect the DUT PC with NIC card to partner pc back via ethernet medium of your choice(RJ45, T1)
+#
+# DUT PC Partner PC
+#┌───────────────────────┐ ┌──────────────────────────┐
+#│ │ │ │
+#│ │ │ │
+#│ ┌───────────┐ │ │
+#│ │DUT NIC │ Eth │ │
+#│ │Interface ─┼─────────────────────────┼─ any eth Interface │
+#│ └───────────┘ │ │
+#│ │ │ │
+#│ │ │ │
+#└───────────────────────┘ └──────────────────────────┘
+#
+#Configurations:
+#To prevent interruptions, Add ethtool, ip to the sudoers list in remote PC and get the ssh key from remote.
+#Required minimum ethtool version is 6.10
+#Change the below configuration based on your hw needs.
+# """Default values"""
+time_delay = 8 #time taken to wait for transitions to happen, in seconds.
+test_duration = 10 #performance test duration for the throughput check, in seconds.
+send_throughput_threshold = 80 #percentage of send throughput required to pass the check
+receive_throughput_threshold = 50 #percentage of receive throughput required to pass the check
+
+import time
+import json
+from lib.py import ksft_run, ksft_exit, ksft_pr, ksft_true
+from lib.py import KsftFailEx, KsftSkipEx
+from lib.py import NetDrvEpEnv
+from lib.py import cmd
+from lib.py import LinkConfig
+
+def verify_throughput(cfg, link_config) -> None:
+ protocols = ["TCP", "UDP"]
+ common_link_modes = link_config.common_link_modes
+ speeds, duplex_modes = link_config.get_speed_duplex_values(common_link_modes)
+ """Test duration in seconds"""
+ duration = test_duration
+ target_ip = cfg.remote_addr
+
+ for protocol in protocols:
+ ksft_pr(f"{protocol} test")
+ test_type = "-u" if protocol == "UDP" else ""
+ send_throughput = []
+ receive_throughput = []
+ for idx in range(0, len(speeds)):
+ bit_rate = f"-b {speeds[idx]}M" if protocol == "UDP" else ""
+ if link_config.set_speed_and_duplex(speeds[idx], duplex_modes[idx]) == False:
+ raise KsftFailEx(f"Not able to set speed and duplex parameters for {cfg.ifname}")
+ time.sleep(time_delay)
+ if link_config.verify_link_up() == False:
+ raise KsftSkipEx(f"Link state of interface {cfg.ifname} is DOWN")
+ send_command=f"iperf3 {test_type} -c {target_ip} {bit_rate} -t {duration} --json"
+ receive_command=f"iperf3 {test_type} -c {target_ip} {bit_rate} -t {duration} --reverse --json"
+ send_result = cmd(send_command)
+ receive_result = cmd(receive_command)
+ if send_result.ret != 0 or receive_result.ret != 0:
+ raise KsftSkipEx("Unexpected error occurred during transmit/receive")
+
+ send_output = send_result.stdout
+ receive_output = receive_result.stdout
+
+ send_data = json.loads(send_output)
+ receive_data = json.loads(receive_output)
+ """Convert throughput to Mbps"""
+ send_throughput.append(round(send_data['end']['sum_sent']['bits_per_second'] / 1e6, 2))
+ receive_throughput.append(round(receive_data['end']['sum_received']['bits_per_second'] / 1e6, 2))
+
+ ksft_pr(f"{protocol}: Send throughput: {send_throughput[idx]} Mbps, Receive throughput: {receive_throughput[idx]} Mbps")
+
+ """Check whether throughput is not below the threshold (default values set at start)"""
+ for idx in range(0, len(speeds)):
+ send_threshold = float(speeds[idx]) * float(send_throughput_threshold / 100)
+ receive_threshold = float(speeds[idx]) * float(receive_throughput_threshold / 100)
+ ksft_true(send_throughput[idx] >= send_threshold, f"{protocol}: Send throughput is below threshold for {speeds[idx]} Mbps in {duplex_modes[idx]} duplex")
+ ksft_true(receive_throughput[idx] >= receive_threshold, f"{protocol}: Receive throughput is below threshold for {speeds[idx]} Mbps in {duplex_modes[idx]} duplex")
+
+def test_throughput(cfg, link_config) -> None:
+ common_link_modes = link_config.common_link_modes
+ if not common_link_modes:
+ KsftSkipEx("No common link modes found")
+ if link_config.partner_netif == None:
+ KsftSkipEx("Partner interface name not available")
+ if link_config.check_autoneg_supported() and link_config.check_autoneg_supported(remote=True):
+ KsftSkipEx("Auto-negotiation not supported by local or remote")
+ cfg.require_cmd("iperf3", remote=True)
+ try:
+ """iperf3 server to be run in the remote pc"""
+ command = "iperf3 -s -D"
+ process = cmd(command, host=cfg.remote)
+ if "Address already in use" in process.stdout:
+ ksft_pr("Iperf server already running in remote")
+ elif process.ret != 0:
+ raise KsftSkipEx("Unable to start server in remote PC")
+ verify_throughput(cfg, link_config)
+ except Exception as e:
+ raise KsftSkipEx(f"Unexpected error occurred: {e}")
+ finally:
+ """Kill existing iperf server in remote pc"""
+ try:
+ cmd("pkill iperf3", host=cfg.remote)
+ except Exception as e:
+ ksft_pr("Unable to stop iperf3 server in remote")
+
+def main() -> None:
+ with NetDrvEpEnv(__file__, nsim_test=False) as cfg:
+ link_config = LinkConfig(cfg)
+ ksft_run(globs=globals(), case_pfx={"test_"}, args=(cfg, link_config,))
+ link_config.reset_interface()
+ ksft_exit()
+
+if __name__ == "__main__":
+ main()
Add selftest case to check the send and receive throughput. Supported link modes between local NIC driver and partner are varied. Then send and receive throughput is captured and verified. Test uses iperf3 tool. Signed-off-by: Mohan Prasad J <mohan.prasad@microchip.com> --- .../testing/selftests/drivers/net/hw/Makefile | 1 + .../drivers/net/hw/nic_performance.py | 121 ++++++++++++++++++ 2 files changed, 122 insertions(+) create mode 100644 tools/testing/selftests/drivers/net/hw/nic_performance.py