@@ -86,16 +86,36 @@ static struct regdata mb86a20s_init[] = {
{ 0x04, 0x13 }, { 0x05, 0xff },
{ 0x04, 0x15 }, { 0x05, 0x4e },
{ 0x04, 0x16 }, { 0x05, 0x20 },
+
+ /*
+ * On this demod, when the bit count reaches the count below,
+ * it collects the bit error count.
+ *
+ * As FE thread runs on every 3 seconds, adjust the counters to
+ * provide one collect before 3 seconds, at the worse case (DQPSK,
+ * 1/4 guard interval, 1/2 FEC, 1-seg rate is 280 Mbps, and
+ * 3 seconds takes 0xcdb9f bits. Rounds it down to 0xccfff
+ *
+ * It should be noticed, however, that, with QAM-64 1/32 guard interval,
+ * 1 segment bit rate is 1.78 Mbps, and 12-seg is about 21.5 Mbps.
+ * At such rate, the time to measure BER is about 40 ms.
+ *
+ * It makes sense to change the logic there to use TMCC parameters and
+ * adjust the counters in order to have all of them to take a little
+ * less than 3 seconds, in order to have a more realistic BER rate,
+ * instead of having short samples for 12-segs.
+ */
{ 0x52, 0x01 }, /* Turn on BER before Viterbi */
- { 0x50, 0xa7 }, { 0x51, 0xff },
- { 0x50, 0xa8 }, { 0x51, 0xff },
+ { 0x50, 0xa7 }, { 0x51, 0x0c },
+ { 0x50, 0xa8 }, { 0x51, 0xcf },
{ 0x50, 0xa9 }, { 0x51, 0xff },
- { 0x50, 0xaa }, { 0x51, 0xff },
- { 0x50, 0xab }, { 0x51, 0xff },
+ { 0x50, 0xaa }, { 0x51, 0x0c },
+ { 0x50, 0xab }, { 0x51, 0xcf },
{ 0x50, 0xac }, { 0x51, 0xff },
- { 0x50, 0xad }, { 0x51, 0xff },
- { 0x50, 0xae }, { 0x51, 0xff },
+ { 0x50, 0xad }, { 0x51, 0x0c },
+ { 0x50, 0xae }, { 0x51, 0xcf },
{ 0x50, 0xaf }, { 0x51, 0xff },
+
{ 0x5e, 0x07 },
{ 0x50, 0xdc }, { 0x51, 0x01 },
{ 0x50, 0xdd }, { 0x51, 0xf4 },
@@ -734,6 +754,14 @@ static int mb86a20s_get_ber_before_vterbi(struct dvb_frontend *fe,
"%s: bit count before Viterbi for layer %c: %d.\n",
__func__, 'A' + layer, *count);
+ /* Reset counter to collect new data */
+ rc = mb86a20s_writereg(state, 0x53, 0x07 & ~(1 << layer));
+ if (rc < 0)
+ return rc;
+ rc = mb86a20s_writereg(state, 0x53, 0x07);
+ if (rc < 0)
+ return rc;
+
return 0;
}
@@ -823,7 +851,11 @@ static int mb86a20s_get_stats(struct dvb_frontend *fe)
}
}
- if (active_layers == ber_layers) {
+ /*
+ * Start showing global count if at least one error count is
+ * available.
+ */
+ if (ber_layers) {
/*
* All BER values are read. We can now calculate the total BER
* And ask for another BER measure
@@ -836,12 +868,6 @@ static int mb86a20s_get_stats(struct dvb_frontend *fe)
c->bit_count.stat[0].scale = FE_SCALE_COUNTER;
c->bit_count.stat[0].uvalue += t_bit_count;
- /* Reset counters to collect new data */
- rc = mb86a20s_writeregdata(state, mb86a20s_vber_reset);
- if (rc < 0)
- dev_err(&state->i2c->dev,
- "%s: Can't reset VBER registers.\n", __func__);
-
/* All BER measures need to be collected when ready */
for (i = 0; i < 3; i++)
state->read_ber[i] = true;
Reduce the bit count from 2^24-1 to 2^16-1 to speedup BER measurement; Do a per-layer reset, instead of waiting for data on all layers; Global stats now start to appear as soon as the first layer (e. g. the one with the biggest number of segments) start to have collected data. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> --- drivers/media/dvb-frontends/mb86a20s.c | 52 +++++++++++++++++++++++++--------- 1 file changed, 39 insertions(+), 13 deletions(-)