@@ -111,13 +111,21 @@ static struct regdata mb86a20s_init[] = {
{ 0x50, 0xdf }, { 0x51, 0xf4 },
{ 0x50, 0xe0 }, { 0x51, 0x01 },
{ 0x50, 0xe1 }, { 0x51, 0xf4 },
- { 0x50, 0xb0 }, { 0x51, 0x07 },
- { 0x50, 0xb2 }, { 0x51, 0xff },
- { 0x50, 0xb3 }, { 0x51, 0xff },
- { 0x50, 0xb4 }, { 0x51, 0xff },
- { 0x50, 0xb5 }, { 0x51, 0xff },
- { 0x50, 0xb6 }, { 0x51, 0xff },
- { 0x50, 0xb7 }, { 0x51, 0xff },
+
+ /*
+ * On this demod, when the block count reaches the count below,
+ * it collects the block error count. The block counters are initialized
+ * to 127 here. This warrants that all of them will be quickly
+ * calculated when device gets locked. As TMCC is parsed, the values
+ * will be adjusted later in the driver's code.
+ */
+ { 0x50, 0xb0 }, { 0x51, 0x07 }, /* Enable PER */
+ { 0x50, 0xb2 }, { 0x51, 0x7f },
+ { 0x50, 0xb3 }, { 0x51, 0x00 },
+ { 0x50, 0xb4 }, { 0x51, 0x7f },
+ { 0x50, 0xb5 }, { 0x51, 0x00 },
+ { 0x50, 0xb6 }, { 0x51, 0x7f },
+ { 0x50, 0xb7 }, { 0x51, 0x00 },
{ 0x50, 0x50 }, { 0x51, 0x02 }, /* MER manual mode */
{ 0x50, 0x51 }, { 0x51, 0x04 }, /* MER symbol 4 */
@@ -893,6 +901,123 @@ static int mb86a20s_get_ber_before_vterbi(struct dvb_frontend *fe,
return 0;
}
+static int mb86a20s_get_blk_error(struct dvb_frontend *fe,
+ unsigned layer,
+ u32 *error, u32 *count)
+{
+ struct mb86a20s_state *state = fe->demodulator_priv;
+ int rc;
+ u32 collect_rate;
+ dev_dbg(&state->i2c->dev, "%s called.\n", __func__);
+
+ if (layer >= 3)
+ return -EINVAL;
+
+ /* Check if the PER measures are already available */
+ rc = mb86a20s_writereg(state, 0x50, 0xb8);
+ if (rc < 0)
+ return rc;
+ rc = mb86a20s_readreg(state, 0x51);
+ if (rc < 0)
+ return rc;
+
+ /* Check if data is available for that layer */
+
+ if (!(rc & (1 << layer))) {
+ dev_dbg(&state->i2c->dev,
+ "%s: block counts for layer %c aren't available yet.\n",
+ __func__, 'A' + layer);
+ return -EBUSY;
+ }
+
+ /* Read Packet error Count */
+ rc = mb86a20s_writereg(state, 0x50, 0xb9 + layer * 2);
+ if (rc < 0)
+ return rc;
+ rc = mb86a20s_readreg(state, 0x51);
+ if (rc < 0)
+ return rc;
+ *error = rc << 8;
+ rc = mb86a20s_writereg(state, 0x50, 0xba + layer * 2);
+ if (rc < 0)
+ return rc;
+ rc = mb86a20s_readreg(state, 0x51);
+ if (rc < 0)
+ return rc;
+ *error |= rc;
+ dev_err(&state->i2c->dev, "%s: block error for layer %c: %d.\n",
+ __func__, 'A' + layer, *error);
+
+ /* Read Bit Count */
+ rc = mb86a20s_writereg(state, 0x50, 0xb2 + layer * 2);
+ if (rc < 0)
+ return rc;
+ rc = mb86a20s_readreg(state, 0x51);
+ if (rc < 0)
+ return rc;
+ *count = rc << 8;
+ rc = mb86a20s_writereg(state, 0x50, 0xb3 + layer * 2);
+ if (rc < 0)
+ return rc;
+ rc = mb86a20s_readreg(state, 0x51);
+ if (rc < 0)
+ return rc;
+ *count |= rc;
+
+ dev_dbg(&state->i2c->dev,
+ "%s: block count for layer %c: %d.\n",
+ __func__, 'A' + layer, *count);
+
+ /*
+ * As we get TMCC data from the frontend, we can better estimate the
+ * BER bit counters, in order to do the BER measure during a longer
+ * time. Use those data, if available, to update the bit count
+ * measure.
+ */
+
+ if (!state->estimated_rate[layer])
+ goto reset_measurement;
+
+ collect_rate = state->estimated_rate[layer] / 204 / 8;
+
+ if (collect_rate < 32)
+ collect_rate = 32;
+ if (collect_rate > 65535)
+ collect_rate = 65535;
+
+ if (collect_rate != *count) {
+ dev_dbg(&state->i2c->dev,
+ "%s: updating PER counter on layer %c to %d.\n",
+ __func__, 'A' + layer, collect_rate);
+ rc = mb86a20s_writereg(state, 0x50, 0xb2 + layer * 2);
+ if (rc < 0)
+ return rc;
+ rc = mb86a20s_writereg(state, 0x51, collect_rate >> 8);
+ if (rc < 0)
+ return rc;
+ rc = mb86a20s_writereg(state, 0x50, 0xb3 + layer * 2);
+ if (rc < 0)
+ return rc;
+ rc = mb86a20s_writereg(state, 0x51, collect_rate & 0xff);
+ if (rc < 0)
+ return rc;
+ }
+
+reset_measurement:
+ /* Reset counter to collect new data */
+ rc = mb86a20s_writereg(state, 0x50, 0xb1);
+ if (rc < 0)
+ return rc;
+ rc = mb86a20s_writereg(state, 0x51, (1 << layer));
+ if (rc < 0)
+ return rc;
+ rc = mb86a20s_writereg(state, 0x51, 0x00);
+ if (rc < 0)
+ return rc;
+
+ return 0;
+}
+
struct linear_segments {
unsigned x, y;
};
@@ -1115,7 +1240,7 @@ static int mb86a20s_get_main_CNR(struct dvb_frontend *fe)
return rc;
}
-static int mb86a20s_get_per_layer_CNR(struct dvb_frontend *fe)
+static int mb86a20s_get_blk_error_layer_CNR(struct dvb_frontend *fe)
{
struct mb86a20s_state *state = fe->demodulator_priv;
struct dtv_frontend_properties *c = &fe->dtv_property_cache;
@@ -1258,14 +1383,16 @@ static int mb86a20s_get_stats(struct dvb_frontend *fe)
int rc = 0, i;
u32 bit_error = 0, bit_count = 0;
u32 t_pre_bit_error = 0, t_pre_bit_count = 0;
- int active_layers = 0, ber_layers = 0;
+ u32 block_error = 0, block_count = 0;
+ u32 t_block_error = 0, t_block_count = 0;
+ int active_layers = 0, ber_layers = 0, per_layers = 0;
dev_dbg(&state->i2c->dev, "%s called.\n", __func__);
mb86a20s_get_main_CNR(fe);
/* Get per-layer stats */
- mb86a20s_get_per_layer_CNR(fe);
+ mb86a20s_get_blk_error_layer_CNR(fe);
for (i = 0; i < 3; i++) {
if (c->isdbt_layer_enabled & (1 << i)) {
@@ -1297,9 +1424,38 @@ static int mb86a20s_get_stats(struct dvb_frontend *fe)
if (c->block_error.stat[1 + i].scale != FE_SCALE_NOT_AVAILABLE)
ber_layers++;
+ /* Handle Block errors for PER/UCB reports */
+ rc = mb86a20s_get_blk_error(fe, i,
+ &block_error,
+ &block_count);
+ if (rc >= 0) {
+ c->block_error.stat[1 + i].scale = FE_SCALE_COUNTER;
+ c->block_error.stat[1 + i].uvalue += block_error;
+ c->block_count.stat[1 + i].scale = FE_SCALE_COUNTER;
+ c->block_count.stat[1 + i].uvalue += block_count;
+ } else if (rc != -EBUSY) {
+ /*
+ * If an I/O error happened,
+ * measures are now unavailable
+ */
+ c->block_error.stat[1 + i].scale = FE_SCALE_NOT_AVAILABLE;
+ c->block_count.stat[1 + i].scale = FE_SCALE_NOT_AVAILABLE;
+ dev_err(&state->i2c->dev,
+ "%s: Can't get PER for layer %c (error %d).\n",
+ __func__, 'A' + i, rc);
+
+ }
+
+ if (c->block_error.stat[1 + i].scale != FE_SCALE_NOT_AVAILABLE)
+ per_layers++;
+
/* Update total BER */
t_pre_bit_error += c->pre_bit_error.stat[1 + i].uvalue;
t_pre_bit_count += c->pre_bit_count.stat[1 + i].uvalue;
+
+ /* Update total PER */
+ t_block_error += c->block_error.stat[1 + i].uvalue;
+ t_block_count += c->block_count.stat[1 + i].uvalue;
}
}
@@ -1321,6 +1477,20 @@ static int mb86a20s_get_stats(struct dvb_frontend *fe)
c->pre_bit_count.stat[0].uvalue = t_pre_bit_count;
}
+ if (per_layers) {
+ /*
+ * At least one per-layer UCB measure was read. We can now
+ * calculate the total UCB
+ *
+ * Total block Error/Count is calculated as the sum of the
+ * block errors on all active layers.
+ */
+ c->block_error.stat[0].scale = FE_SCALE_COUNTER;
+ c->block_error.stat[0].uvalue = t_block_error;
+ c->block_count.stat[0].scale = FE_SCALE_COUNTER;
+ c->block_count.stat[0].uvalue = t_block_count;
+ }
+
return rc;
}
Add both per-layer and global block error count and block count, for PER and UCB measurements. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> --- drivers/media/dvb-frontends/mb86a20s.c | 190 +++++++++++++++++++++++++++++++-- 1 file changed, 180 insertions(+), 10 deletions(-)