| Message ID | 1394122819-9582-2-git-send-email-s.nawrocki@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Sylwester, On Thu, Mar 6, 2014 at 5:20 PM, Sylwester Nawrocki <s.nawrocki@samsung.com> wrote: > This patch adds binding documentation for the Samsung S5K6A3(YX) > raw image sensor. > > Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> > Acked-by: Kyungmin Park <kyungmin.park@samsung.com> > Acked-by: Mark Rutland <mark.rutland@arm.com> > --- > Changes since v5: > - none. > > Changes since v2: > - rephrased 'clocks' and 'clock-names' properties' description; > --- > .../devicetree/bindings/media/samsung-s5k6a3.txt | 33 ++++++++++++++++++++ > 1 file changed, 33 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/samsung-s5k6a3.txt > > diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt > new file mode 100644 > index 0000000..cce01e8 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt > @@ -0,0 +1,33 @@ > +Samsung S5K6A3(YX) raw image sensor > +--------------------------------- > + > +S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces > +and CCI (I2C compatible) control bus. > + > +Required properties: > + > +- compatible : "samsung,s5k6a3"; > +- reg : I2C slave address of the sensor; > +- svdda-supply : core voltage supply; > +- svddio-supply : I/O voltage supply; > +- afvdd-supply : AF (actuator) voltage supply; > +- gpios : specifier of a GPIO connected to the RESET pin; Please use 'reset-gpios' for GPIOs connected to reset pins. regards Philipp -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Phillip, On 03/06/2014 07:08 PM, Philipp Zabel wrote: >> +++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt >> > @@ -0,0 +1,33 @@ >> > +Samsung S5K6A3(YX) raw image sensor >> > +--------------------------------- >> > + >> > +S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces >> > +and CCI (I2C compatible) control bus. >> > + >> > +Required properties: >> > + >> > +- compatible : "samsung,s5k6a3"; >> > +- reg : I2C slave address of the sensor; >> > +- svdda-supply : core voltage supply; >> > +- svddio-supply : I/O voltage supply; >> > +- afvdd-supply : AF (actuator) voltage supply; >> > +- gpios : specifier of a GPIO connected to the RESET pin; > > Please use 'reset-gpios' for GPIOs connected to reset pins. I would prefer to keep it as is, I'm not adding a new driver in this series, just the binding documentation and doing some refactoring. So if I changed this now, the driver would need to be messed up with an additional code to support both 'gpios' and 'reset-gpios'. Are there any serious reasons to use this specific name ? It's not related to the reset signal DT bindings, is it ? -- Regards, Sylwester -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt new file mode 100644 index 0000000..cce01e8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt @@ -0,0 +1,33 @@ +Samsung S5K6A3(YX) raw image sensor +--------------------------------- + +S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces +and CCI (I2C compatible) control bus. + +Required properties: + +- compatible : "samsung,s5k6a3"; +- reg : I2C slave address of the sensor; +- svdda-supply : core voltage supply; +- svddio-supply : I/O voltage supply; +- afvdd-supply : AF (actuator) voltage supply; +- gpios : specifier of a GPIO connected to the RESET pin; +- clocks : should contain list of phandle and clock specifier pairs + according to common clock bindings for the clocks described + in the clock-names property; +- clock-names : should contain "extclk" entry for the sensor's EXTCLK clock; + +Optional properties: + +- clock-frequency : the frequency at which the "extclk" clock should be + configured to operate, in Hz; if this property is not + specified default 24 MHz value will be used. + +The common video interfaces bindings (see video-interfaces.txt) should be +used to specify link to the image data receiver. The S5K6A3(YX) device +node should contain one 'port' child node with an 'endpoint' subnode. + +Following properties are valid for the endpoint node: + +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in + video-interfaces.txt. The sensor supports only one data lane.