| Message ID | 1397583272-28295-2-git-send-email-s.nawrocki@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Sylwester Nawrocki wrote: > > S5PV210 is going to get DT support, so we can remove the camera > bits from the only board using camera on S5PV210. This allows to > clean the exynos4-is driver by dropping code for non-dt platforms. > This patch can be dropped if a patch removing the whole board > file is applied first. > > Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> > Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Hi Sylwester, Cleanup is always welcome ;-) I think, when this series is ready for mainline, this will be handled in media tree. So, Acked-by: Kukjin Kim <kgene.kim@samsung.com> Thanks, Kukjin > --- > arch/arm/mach-s5pv210/mach-goni.c | 51 --------------------------------- > ---- > 1 file changed, 51 deletions(-) > > diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach- > s5pv210/mach-goni.c > index b41a38a..6c719ec 100644 > --- a/arch/arm/mach-s5pv210/mach-goni.c > +++ b/arch/arm/mach-s5pv210/mach-goni.c > @@ -49,11 +49,6 @@ > #include <plat/clock.h> > #include <plat/samsung-time.h> > #include <plat/mfc.h> > -#include <plat/camport.h> > - > -#include <media/v4l2-mediabus.h> > -#include <media/s5p_fimc.h> > -#include <media/noon010pc30.h> > > #include "common.h" > > @@ -285,14 +280,6 @@ static void __init goni_tsp_init(void) > /* USB OTG */ > static struct s3c_hsotg_plat goni_hsotg_pdata; > > -static void goni_camera_init(void) > -{ > - s5pv210_fimc_setup_gpio(S5P_CAMPORT_A); > - > - /* Set max driver strength on CAM_A_CLKOUT pin. */ > - s5p_gpio_set_drvstr(S5PV210_GPE1(3), S5P_GPIO_DRVSTR_LV4); > -} > - > /* MAX8998 regulators */ > #if defined(CONFIG_REGULATOR_MAX8998) || > defined(CONFIG_REGULATOR_MAX8998_MODULE) > > @@ -825,34 +812,6 @@ static void goni_setup_sdhci(void) > s3c_sdhci2_set_platdata(&goni_hsmmc2_data); > }; > > -static struct noon010pc30_platform_data noon010pc30_pldata = { > - .clk_rate = 16000000UL, > - .gpio_nreset = S5PV210_GPB(2), /* CAM_CIF_NRST */ > - .gpio_nstby = S5PV210_GPB(0), /* CAM_CIF_NSTBY */ > -}; > - > -static struct i2c_board_info noon010pc30_board_info = { > - I2C_BOARD_INFO("NOON010PC30", 0x60 >> 1), > - .platform_data = &noon010pc30_pldata, > -}; > - > -static struct fimc_source_info goni_camera_sensors[] = { > - { > - .mux_id = 0, > - .flags = V4L2_MBUS_PCLK_SAMPLE_FALLING | > - V4L2_MBUS_VSYNC_ACTIVE_LOW, > - .fimc_bus_type = FIMC_BUS_TYPE_ITU_601, > - .board_info = &noon010pc30_board_info, > - .i2c_bus_num = 0, > - .clk_frequency = 16000000UL, > - }, > -}; > - > -static struct s5p_platform_fimc goni_fimc_md_platdata __initdata = { > - .source_info = goni_camera_sensors, > - .num_clients = ARRAY_SIZE(goni_camera_sensors), > -}; > - > /* Audio device */ > static struct platform_device goni_device_audio = { > .name = "smdk-audio", > @@ -874,10 +833,6 @@ static struct platform_device *goni_devices[] > __initdata = { > &s5p_device_mixer, > &s5p_device_sdo, > &s3c_device_i2c0, > - &s5p_device_fimc0, > - &s5p_device_fimc1, > - &s5p_device_fimc2, > - &s5p_device_fimc_md, > &s3c_device_hsmmc0, > &s3c_device_hsmmc1, > &s3c_device_hsmmc2, > @@ -946,14 +901,8 @@ static void __init goni_machine_init(void) > /* FB */ > s3c_fb_set_platdata(&goni_lcd_pdata); > > - /* FIMC */ > - s3c_set_platdata(&goni_fimc_md_platdata, > sizeof(goni_fimc_md_platdata), > - &s5p_device_fimc_md); > - > s3c_hsotg_set_platdata(&goni_hsotg_pdata); > > - goni_camera_init(); > - > /* SPI */ > spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info)); > > -- > 1.7.9.5 -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 02/05/14 08:07, Kukjin Kim wrote: > Sylwester Nawrocki wrote: >> > >> > S5PV210 is going to get DT support, so we can remove the camera >> > bits from the only board using camera on S5PV210. This allows to >> > clean the exynos4-is driver by dropping code for non-dt platforms. >> > This patch can be dropped if a patch removing the whole board >> > file is applied first. >> > >> > Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> >> > Acked-by: Kyungmin Park <kyungmin.park@samsung.com> > > Hi Sylwester, > > Cleanup is always welcome ;-) > > I think, when this series is ready for mainline, this will be handled in > media tree. So, > > Acked-by: Kukjin Kim <kgene.kim@samsung.com> Hi Kukjin, Thank you, patch queued up for the media tree! -- Regards, Sylwester -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach-s5pv210/mach-goni.c index b41a38a..6c719ec 100644 --- a/arch/arm/mach-s5pv210/mach-goni.c +++ b/arch/arm/mach-s5pv210/mach-goni.c @@ -49,11 +49,6 @@ #include <plat/clock.h> #include <plat/samsung-time.h> #include <plat/mfc.h> -#include <plat/camport.h> - -#include <media/v4l2-mediabus.h> -#include <media/s5p_fimc.h> -#include <media/noon010pc30.h> #include "common.h" @@ -285,14 +280,6 @@ static void __init goni_tsp_init(void) /* USB OTG */ static struct s3c_hsotg_plat goni_hsotg_pdata; -static void goni_camera_init(void) -{ - s5pv210_fimc_setup_gpio(S5P_CAMPORT_A); - - /* Set max driver strength on CAM_A_CLKOUT pin. */ - s5p_gpio_set_drvstr(S5PV210_GPE1(3), S5P_GPIO_DRVSTR_LV4); -} - /* MAX8998 regulators */ #if defined(CONFIG_REGULATOR_MAX8998) || defined(CONFIG_REGULATOR_MAX8998_MODULE) @@ -825,34 +812,6 @@ static void goni_setup_sdhci(void) s3c_sdhci2_set_platdata(&goni_hsmmc2_data); }; -static struct noon010pc30_platform_data noon010pc30_pldata = { - .clk_rate = 16000000UL, - .gpio_nreset = S5PV210_GPB(2), /* CAM_CIF_NRST */ - .gpio_nstby = S5PV210_GPB(0), /* CAM_CIF_NSTBY */ -}; - -static struct i2c_board_info noon010pc30_board_info = { - I2C_BOARD_INFO("NOON010PC30", 0x60 >> 1), - .platform_data = &noon010pc30_pldata, -}; - -static struct fimc_source_info goni_camera_sensors[] = { - { - .mux_id = 0, - .flags = V4L2_MBUS_PCLK_SAMPLE_FALLING | - V4L2_MBUS_VSYNC_ACTIVE_LOW, - .fimc_bus_type = FIMC_BUS_TYPE_ITU_601, - .board_info = &noon010pc30_board_info, - .i2c_bus_num = 0, - .clk_frequency = 16000000UL, - }, -}; - -static struct s5p_platform_fimc goni_fimc_md_platdata __initdata = { - .source_info = goni_camera_sensors, - .num_clients = ARRAY_SIZE(goni_camera_sensors), -}; - /* Audio device */ static struct platform_device goni_device_audio = { .name = "smdk-audio", @@ -874,10 +833,6 @@ static struct platform_device *goni_devices[] __initdata = { &s5p_device_mixer, &s5p_device_sdo, &s3c_device_i2c0, - &s5p_device_fimc0, - &s5p_device_fimc1, - &s5p_device_fimc2, - &s5p_device_fimc_md, &s3c_device_hsmmc0, &s3c_device_hsmmc1, &s3c_device_hsmmc2, @@ -946,14 +901,8 @@ static void __init goni_machine_init(void) /* FB */ s3c_fb_set_platdata(&goni_lcd_pdata); - /* FIMC */ - s3c_set_platdata(&goni_fimc_md_platdata, sizeof(goni_fimc_md_platdata), - &s5p_device_fimc_md); - s3c_hsotg_set_platdata(&goni_hsotg_pdata); - goni_camera_init(); - /* SPI */ spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));