diff mbox

[v4,1/9] dt-bindings: media: Add Renesas CEU bindings

Message ID 1515515131-13760-2-git-send-email-jacopo+renesas@jmondi.org (mailing list archive)
State New, archived
Headers show

Commit Message

Jacopo Mondi Jan. 9, 2018, 4:25 p.m. UTC
Add bindings documentation for Renesas Capture Engine Unit (CEU).

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
 .../devicetree/bindings/media/renesas,ceu.txt      | 81 ++++++++++++++++++++++
 1 file changed, 81 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/renesas,ceu.txt

Comments

Rob Herring Jan. 11, 2018, 10:28 p.m. UTC | #1
On Tue, Jan 09, 2018 at 05:25:23PM +0100, Jacopo Mondi wrote:
> Add bindings documentation for Renesas Capture Engine Unit (CEU).
> 
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> ---
>  .../devicetree/bindings/media/renesas,ceu.txt      | 81 ++++++++++++++++++++++
>  1 file changed, 81 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/renesas,ceu.txt

Reviewed-by: Rob Herring <robh@kernel.org>
Laurent Pinchart Jan. 11, 2018, 10:50 p.m. UTC | #2
Hi Jacopo,

Thank you for the patch.

On Tuesday, 9 January 2018 18:25:23 EET Jacopo Mondi wrote:
> Add bindings documentation for Renesas Capture Engine Unit (CEU).
> 
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
>  .../devicetree/bindings/media/renesas,ceu.txt      | 81
> ++++++++++++++++++++++ 1 file changed, 81 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/renesas,ceu.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.txt
> b/Documentation/devicetree/bindings/media/renesas,ceu.txt new file mode
> 100644
> index 0000000..590ee27
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/renesas,ceu.txt
> @@ -0,0 +1,81 @@
> +Renesas Capture Engine Unit (CEU)
> +----------------------------------------------
> +
> +The Capture Engine Unit is the image capture interface found in the Renesas
> +SH Mobile and RZ SoCs.
> +
> +The interface supports a single parallel input with data bus width of 8 or
> 16 +bits.
> +
> +Required properties:
> +- compatible: Shall be "renesas,r7s72100-ceu" for CEU units found in
> RZ/A1-H +  and RZ/A1-M SoCs.
> +- reg: Registers address base and size.
> +- interrupts: The interrupt specifier.
> +
> +The CEU supports a single parallel input and should contain a single 'port'
> +subnode with a single 'endpoint'. Connection to input devices are modeled
> +according to the video interfaces OF bindings specified in:
> +Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> +Optional endpoint properties applicable to parallel input bus described in
> +the above mentioned "video-interfaces.txt" file are supported.
> +
> +- hsync-active: Active state of the HSYNC signal, 0/1 for LOW/HIGH
> respectively. +  If property is not present, default is active high.
> +- vsync-active: Active state of the VSYNC signal, 0/1 for LOW/HIGH
> respectively. +  If property is not present, default is active high.
> +
> +Example:
> +
> +The example describes the connection between the Capture Engine Unit and an
> +OV7670 image sensor connected to i2c1 interface.
> +
> +ceu: ceu@e8210000 {
> +	reg = <0xe8210000 0x209c>;
> +	compatible = "renesas,r7s72100-ceu";
> +	interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&vio_pins>;
> +
> +	status = "okay";
> +
> +	port {
> +		ceu_in: endpoint {
> +			remote-endpoint = <&ov7670_out>;
> +
> +			hsync-active = <1>;
> +			vsync-active = <0>;
> +		};
> +	};
> +};
> +
> +i2c1: i2c@fcfee400 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c1_pins>;
> +
> +	status = "okay";
> +
> +	clock-frequency = <100000>;
> +
> +	ov7670: camera@21 {
> +		compatible = "ovti,ov7670";
> +		reg = <0x21>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vio_pins>;
> +
> +		reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>;
> +		powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>;
> +
> +		port {
> +			ov7670_out: endpoint {
> +				remote-endpoint = <&ceu_in>;
> +
> +				hsync-active = <1>;
> +				vsync-active = <0>;
> +			};
> +		};
> +	};
> +};
Simon Horman Jan. 12, 2018, 6:48 a.m. UTC | #3
On Fri, Jan 12, 2018 at 12:50:41AM +0200, Laurent Pinchart wrote:
> Hi Jacopo,
> 
> Thank you for the patch.
> 
> On Tuesday, 9 January 2018 18:25:23 EET Jacopo Mondi wrote:
> > Add bindings documentation for Renesas Capture Engine Unit (CEU).
> > 
> > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> 
> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Hi,

I see that these bindings have now been reviewed. What is their (likely)
path to upstream from here? I'd like to accept the related DTS changes
once there is a clear path for the bindings to land in upstream.
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.txt b/Documentation/devicetree/bindings/media/renesas,ceu.txt
new file mode 100644
index 0000000..590ee27
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/renesas,ceu.txt
@@ -0,0 +1,81 @@ 
+Renesas Capture Engine Unit (CEU)
+----------------------------------------------
+
+The Capture Engine Unit is the image capture interface found in the Renesas
+SH Mobile and RZ SoCs.
+
+The interface supports a single parallel input with data bus width of 8 or 16
+bits.
+
+Required properties:
+- compatible: Shall be "renesas,r7s72100-ceu" for CEU units found in RZ/A1-H
+  and RZ/A1-M SoCs.
+- reg: Registers address base and size.
+- interrupts: The interrupt specifier.
+
+The CEU supports a single parallel input and should contain a single 'port'
+subnode with a single 'endpoint'. Connection to input devices are modeled
+according to the video interfaces OF bindings specified in:
+Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Optional endpoint properties applicable to parallel input bus described in
+the above mentioned "video-interfaces.txt" file are supported.
+
+- hsync-active: Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
+  If property is not present, default is active high.
+- vsync-active: Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
+  If property is not present, default is active high.
+
+Example:
+
+The example describes the connection between the Capture Engine Unit and an
+OV7670 image sensor connected to i2c1 interface.
+
+ceu: ceu@e8210000 {
+	reg = <0xe8210000 0x209c>;
+	compatible = "renesas,r7s72100-ceu";
+	interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&vio_pins>;
+
+	status = "okay";
+
+	port {
+		ceu_in: endpoint {
+			remote-endpoint = <&ov7670_out>;
+
+			hsync-active = <1>;
+			vsync-active = <0>;
+		};
+	};
+};
+
+i2c1: i2c@fcfee400 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	status = "okay";
+
+	clock-frequency = <100000>;
+
+	ov7670: camera@21 {
+		compatible = "ovti,ov7670";
+		reg = <0x21>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vio_pins>;
+
+		reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>;
+		powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>;
+
+		port {
+			ov7670_out: endpoint {
+				remote-endpoint = <&ceu_in>;
+
+				hsync-active = <1>;
+				vsync-active = <0>;
+			};
+		};
+	};
+};