@@ -231,7 +231,9 @@ struct tm6000_board tm6000_boards[] = {
.has_remote = 1,
},
.gpio = {
- .tuner_reset = TM6000_GPIO_2,
+ .tuner_reset = TM6010_GPIO_0,
+ .demod_reset = TM6010_GPIO_1,
+ .power_led = TM6010_GPIO_6,
},
},
[TM6010_BOARD_BEHOLD_VOYAGER] = {
@@ -247,7 +249,8 @@ struct tm6000_board tm6000_boards[] = {
.has_remote = 1,
},
.gpio = {
- .tuner_reset = TM6000_GPIO_2,
+ .tuner_reset = TM6010_GPIO_0,
+ .power_led = TM6010_GPIO_6,
},
},
[TM6010_BOARD_TERRATEC_CINERGY_HYBRID_XE] = {
@@ -320,6 +323,31 @@ struct usb_device_id tm6000_id_table [] = {
{ },
};
+/* Tuner callback to provide the proper gpio changes needed for xc5000 */
+int tm6000_xc5000_callback(void *ptr, int component, int command, int arg)
+{
+ int rc = 0;
+ struct tm6000_core *dev = ptr;
+
+ if (dev->tuner_type != TUNER_XC5000)
+ return 0;
+
+ switch (command) {
+ case XC5000_TUNER_RESET:
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ dev->gpio.tuner_reset, 0x01);
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ dev->gpio.tuner_reset, 0x00);
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ dev->gpio.tuner_reset, 0x01);
+ break;
+ }
+ return (rc);
+}
+
+
/* Tuner callback to provide the proper gpio changes needed for xc2028 */
int tm6000_tuner_callback(void *ptr, int component, int command, int arg)
@@ -438,6 +466,21 @@ int tm6000_cards_setup(struct tm6000_core *dev)
tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN, dev->gpio.demod_on, 0x00);
msleep(15);
break;
+ case TM6010_BOARD_BEHOLD_WANDER:
+ /* Power led on (blue) */
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN, dev->gpio.power_led, 0x01);
+ msleep(15);
+ /* Reset zarlink zl10353 */
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN, dev->gpio.demod_reset, 0x00);
+ msleep(50);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN, dev->gpio.demod_reset, 0x01);
+ msleep(15);
+ break;
+ case TM6010_BOARD_BEHOLD_VOYAGER:
+ /* Power led on (blue) */
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN, dev->gpio.power_led, 0x01);
+ msleep(15);
+ break;
default:
break;
}
@@ -449,42 +492,38 @@ int tm6000_cards_setup(struct tm6000_core *dev)
* If a device uses a different sequence or different GPIO pins for
* reset, just add the code at the board-specific part
*/
- for (i = 0; i < 2; i++) {
- rc = tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
- dev->gpio.tuner_reset, 0x00);
- if (rc < 0) {
- printk(KERN_ERR "Error %i doing GPIO1 reset\n", rc);
- return rc;
- }
-
- msleep(10); /* Just to be conservative */
- rc = tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
- dev->gpio.tuner_reset, 0x01);
- if (rc < 0) {
- printk(KERN_ERR "Error %i doing GPIO1 reset\n", rc);
- return rc;
- }
- msleep(10);
- rc = tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN, TM6000_GPIO_4, 0);
- if (rc < 0) {
- printk(KERN_ERR "Error %i doing GPIO4 reset\n", rc);
- return rc;
- }
+ if (dev->gpio.tuner_reset)
+ {
+ for (i = 0; i < 2; i++) {
+ rc = tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ dev->gpio.tuner_reset, 0x00);
+ if (rc < 0) {
+ printk(KERN_ERR "Error %i doing tuner reset\n", rc);
+ return rc;
+ }
- msleep(10);
- rc = tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN, TM6000_GPIO_4, 1);
- if (rc < 0) {
- printk(KERN_ERR "Error %i doing GPIO4 reset\n", rc);
- return rc;
- }
+ msleep(10); /* Just to be conservative */
+ rc = tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ dev->gpio.tuner_reset, 0x01);
+ if (rc < 0) {
+ printk(KERN_ERR "Error %i doing tuner reset\n", rc);
+ return rc;
+ }
+ msleep(10);
- if (!i) {
- rc = tm6000_get_reg32(dev, REQ_40_GET_VERSION, 0, 0);
- if (rc >= 0)
- printk(KERN_DEBUG "board=0x%08x\n", rc);
+ if (!i) {
+ rc = tm6000_get_reg32(dev, REQ_40_GET_VERSION, 0, 0);
+ if (rc >= 0)
+ printk(KERN_DEBUG "board=0x%08x\n", rc);
+ }
}
}
+ else
+ {
+ printk(KERN_ERR "Tuner reset is not configured\n");
+ return -1;
+ }
msleep(50);
@@ -502,12 +541,30 @@ static void tm6000_config_tuner (struct tm6000_core *dev)
memset(&tun_setup, 0, sizeof(tun_setup));
tun_setup.type = dev->tuner_type;
tun_setup.addr = dev->tuner_addr;
- tun_setup.mode_mask = T_ANALOG_TV | T_RADIO | T_DIGITAL_TV;
- tun_setup.tuner_callback = tm6000_tuner_callback;
+
+ tun_setup.mode_mask = 0;
+ if (dev->caps.has_tuner)
+ tun_setup.mode_mask |= (T_ANALOG_TV | T_RADIO);
+ if (dev->caps.has_dvb)
+ tun_setup.mode_mask |= T_DIGITAL_TV;
+
+ switch (dev->tuner_type)
+ {
+ case TUNER_XC2028:
+ tun_setup.tuner_callback = tm6000_tuner_callback;;
+ break;
+ case TUNER_XC5000:
+ tun_setup.tuner_callback = tm6000_xc5000_callback;
+ break;
+ }
+
v4l2_device_call_all(&dev->v4l2_dev, 0, tuner, s_type_addr, &tun_setup);
- if (dev->tuner_type == TUNER_XC2028) {
+ switch (dev->tuner_type)
+ {
+ case TUNER_XC2028:
+ {
struct v4l2_priv_tun_config xc2028_cfg;
struct xc2028_ctrl ctl;
@@ -537,9 +594,31 @@ static void tm6000_config_tuner (struct tm6000_core *dev)
}
printk(KERN_INFO "Setting firmware parameters for xc2028\n");
-
v4l2_device_call_all(&dev->v4l2_dev, 0, tuner, s_config,
&xc2028_cfg);
+
+ }
+ break;
+ case TUNER_XC5000:
+ {
+ struct v4l2_priv_tun_config xc5000_cfg;
+ struct xc5000_config ctl = {
+ .i2c_address = dev->tuner_addr,
+ .if_khz = 4570,
+ .radio_input = XC5000_RADIO_FM1,
+ };
+
+ xc5000_cfg.tuner = TUNER_XC5000;
+ xc5000_cfg.priv = &ctl;
+
+
+ v4l2_device_call_all(&dev->v4l2_dev, 0, tuner, s_config,
+ &xc5000_cfg);
+ }
+ break;
+ default:
+ printk(KERN_INFO "Unknown tuner type. Tuner is not configured.\n");
+ break;
}
}
@@ -216,6 +216,7 @@ struct tm6000_fh {
/* In tm6000-cards.c */
int tm6000_tuner_callback (void *ptr, int component, int command, int arg);
+int tm6000_xc5000_callback (void *ptr, int component, int command, int arg);
int tm6000_cards_setup(struct tm6000_core *dev);
/* In tm6000-core.c */
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>