@@ -10,18 +10,21 @@
* adr: I2C Address of the DRX-K
* single_master: Device is on the single master mode
* no_i2c_bridge: Don't switch the I2C bridge to talk with tuner
- * antenna_uses_gpio: Use GPIO to control the antenna
- * antenna_dvbc: GPIO for changing antenna to DVB-C
- * antenna_dvbt: GPIO for changing antenna to DVB-T
+ * antenna_gpio: GPIO bit used to control the antenna
+ * antenna_dvbt: GPIO bit for changing antenna to DVB-C. A value of 1
+ * means that 1=DVBC, 0 = DVBT. Zero means the opposite.
* microcode_name: Name of the firmware file with the microcode
+ *
+ * On the *_gpio vars, bit 0 is UIO-1, bit 1 is UIO-2 and bit 2 is
+ * UIO-3.
*/
struct drxk_config {
u8 adr;
bool single_master;
bool no_i2c_bridge;
- bool antenna_uses_gpio;
- u16 antenna_dvbc, antenna_dvbt;
+ bool antenna_dvbt;
+ u16 antenna_gpio;
const char *microcode_name;
};
@@ -856,7 +856,6 @@ static int init_state(struct drxk_state *state)
state->m_agcFastClipCtrlDelay = 0;
state->m_GPIOCfg = (ulGPIOCfg);
- state->m_GPIO = (ulGPIO == 0 ? 0 : 1);
state->m_bPowerDown = false;
state->m_currentPowerMode = DRX_POWER_DOWN;
@@ -5795,24 +5794,63 @@ static int WriteGPIO(struct drxk_state *state)
goto error;
if (state->m_hasSAWSW) {
- /* write to io pad configuration register - output mode */
- status = write16(state, SIO_PDR_SMA_TX_CFG__A, state->m_GPIOCfg);
- if (status < 0)
- goto error;
+ if (state->UIO_mask & 0x0001) { /* UIO-1 */
+ /* write to io pad configuration register - output mode */
+ status = write16(state, SIO_PDR_SMA_TX_CFG__A, state->m_GPIOCfg);
+ if (status < 0)
+ goto error;
- /* use corresponding bit in io data output registar */
- status = read16(state, SIO_PDR_UIO_OUT_LO__A, &value);
- if (status < 0)
- goto error;
- if (state->m_GPIO == 0)
- value &= 0x7FFF; /* write zero to 15th bit - 1st UIO */
- else
- value |= 0x8000; /* write one to 15th bit - 1st UIO */
- /* write back to io data output register */
- status = write16(state, SIO_PDR_UIO_OUT_LO__A, value);
- if (status < 0)
- goto error;
+ /* use corresponding bit in io data output registar */
+ status = read16(state, SIO_PDR_UIO_OUT_LO__A, &value);
+ if (status < 0)
+ goto error;
+ if ((state->m_GPIO & 0x0001) == 0)
+ value &= 0x7FFF; /* write zero to 15th bit - 1st UIO */
+ else
+ value |= 0x8000; /* write one to 15th bit - 1st UIO */
+ /* write back to io data output register */
+ status = write16(state, SIO_PDR_UIO_OUT_LO__A, value);
+ if (status < 0)
+ goto error;
+ }
+ if (state->UIO_mask & 0x0002) { /* UIO-2 */
+ /* write to io pad configuration register - output mode */
+ status = write16(state, SIO_PDR_SMA_TX_CFG__A, state->m_GPIOCfg);
+ if (status < 0)
+ goto error;
+ /* use corresponding bit in io data output registar */
+ status = read16(state, SIO_PDR_UIO_OUT_LO__A, &value);
+ if (status < 0)
+ goto error;
+ if ((state->m_GPIO & 0x0002) == 0)
+ value &= 0xBFFF; /* write zero to 14th bit - 2st UIO */
+ else
+ value |= 0x4000; /* write one to 14th bit - 2st UIO */
+ /* write back to io data output register */
+ status = write16(state, SIO_PDR_UIO_OUT_LO__A, value);
+ if (status < 0)
+ goto error;
+ }
+ if (state->UIO_mask & 0x0004) { /* UIO-3 */
+ /* write to io pad configuration register - output mode */
+ status = write16(state, SIO_PDR_SMA_TX_CFG__A, state->m_GPIOCfg);
+ if (status < 0)
+ goto error;
+
+ /* use corresponding bit in io data output registar */
+ status = read16(state, SIO_PDR_UIO_OUT_LO__A, &value);
+ if (status < 0)
+ goto error;
+ if ((state->m_GPIO & 0x0004) == 0)
+ value &= 0xFFFB; /* write zero to 2nd bit - 3rd UIO */
+ else
+ value |= 0x0004; /* write one to 2nd bit - 3rd UIO */
+ /* write back to io data output register */
+ status = write16(state, SIO_PDR_UIO_OUT_LO__A, value);
+ if (status < 0)
+ goto error;
+ }
}
/* Write magic word to disable pdr reg write */
status = write16(state, SIO_TOP_COMM_KEY__A, 0x0000);
@@ -5825,14 +5863,22 @@ error:
static int SwitchAntennaToQAM(struct drxk_state *state)
{
int status = 0;
+ bool gpio_state;
dprintk(1, "\n");
- if (state->m_AntennaSwitchDVBTDVBC != 0) {
- if (state->m_GPIO != state->m_AntennaDVBC) {
- state->m_GPIO = state->m_AntennaDVBC;
- status = WriteGPIO(state);
- }
+ if (!state->antenna_gpio)
+ return 0;
+
+ gpio_state = state->m_GPIO & state->antenna_gpio;
+
+ if (state->antenna_dvbt ^ gpio_state) {
+ /* Antenna is on DVB-T mode. Switch */
+ if (state->antenna_dvbt)
+ state->m_GPIO &= ~state->antenna_gpio;
+ else
+ state->m_GPIO |= state->antenna_gpio;
+ status = WriteGPIO(state);
}
if (status < 0)
printk(KERN_ERR "drxk: Error %d on %s\n", status, __func__);
@@ -5842,13 +5888,22 @@ static int SwitchAntennaToQAM(struct drxk_state *state)
static int SwitchAntennaToDVBT(struct drxk_state *state)
{
int status = 0;
+ bool gpio_state;
dprintk(1, "\n");
- if (state->m_AntennaSwitchDVBTDVBC != 0) {
- if (state->m_GPIO != state->m_AntennaDVBT) {
- state->m_GPIO = state->m_AntennaDVBT;
- status = WriteGPIO(state);
- }
+
+ if (!state->antenna_gpio)
+ return 0;
+
+ gpio_state = state->m_GPIO & state->antenna_gpio;
+
+ if (!(state->antenna_dvbt ^ gpio_state)) {
+ /* Antenna is on DVB-C mode. Switch */
+ if (state->antenna_dvbt)
+ state->m_GPIO |= state->antenna_gpio;
+ else
+ state->m_GPIO &= ~state->antenna_gpio;
+ status = WriteGPIO(state);
}
if (status < 0)
printk(KERN_ERR "drxk: Error %d on %s\n", status, __func__);
@@ -6350,9 +6405,17 @@ struct dvb_frontend *drxk_attach(const struct drxk_config *config,
state->single_master = config->single_master;
state->microcode_name = config->microcode_name;
state->no_i2c_bridge = config->no_i2c_bridge;
- state->m_AntennaSwitchDVBTDVBC = config->antenna_uses_gpio;
- state->m_AntennaDVBC = config->antenna_dvbc;
- state->m_AntennaDVBT = config->antenna_dvbt;
+ state->antenna_gpio = config->antenna_gpio;
+ state->antenna_dvbt = config->antenna_dvbt;
+
+ /* NOTE: as more UIO bits will be used, add them to the mask */
+ state->UIO_mask = config->antenna_gpio;
+
+ /* Default gpio to DVB-C */
+ if (!state->antenna_dvbt && state->antenna_gpio)
+ state->m_GPIO |= state->antenna_gpio;
+ else
+ state->m_GPIO &= ~state->antenna_gpio;
mutex_init(&state->mutex);
mutex_init(&state->ctlock);
@@ -323,17 +323,19 @@ struct drxk_state {
enum DRXPowerMode m_currentPowerMode;
- /* Configurable parameters at the driver */
+ /*
+ * Configurable parameters at the driver. They stores the values found
+ * at struct drxk_config.
+ */
- bool m_AntennaSwitchDVBTDVBC;
- u16 m_AntennaDVBC;
- u16 m_AntennaDVBT;
+ u16 UIO_mask; /* Bits used by UIO */
- u32 single_master : 1; /* Use single master i2c mode */
- u32 no_i2c_bridge : 1; /* Tuner is not on port 1, don't use I2C bridge */
+ bool single_master;
+ bool no_i2c_bridge;
+ bool antenna_dvbt;
+ u16 antenna_gpio;
const char *microcode_name;
-
};
#define NEVER_LOCK 0
The driver is too limited: it assumes that UIO is used only for controlling the antenna, and that only UIO-1 is in usage. However, from Terratec H7 driver [1], 3 UIO's can be used. In fact, it seems that H7 needs to use all 3. So, make the code generic enough to handle the most complex scenario. For now, only antena GPIO can be specified, but is is easier now to add the other GPIO/UIO needs. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>