[v6,1/2] media:imx274 device tree binding file

Commit Message

Leon Luo Sept. 24, 2017, 7:53 a.m. UTC

The binding file for imx274 CMOS sensor V4l2 driver

Signed-off-by: Leon Luo <[e-mail]>
---
v6:
 - no changes
v5:
 - add 'port' and 'endpoint' information
v4:
 - no changes
v3:
 - remove redundant properties and references
 - document 'reg' property
v2:
 - no changes
---
 .../devicetree/bindings/media/i2c/imx274.txt       | 33 ++++++++++++++++++++++
 1 file changed, 33 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/imx274.txt

Comments

Rob Herring (Arm) Sept. 24, 2017, 7:39 p.m. UTC | #1

On Sun, Sep 24, 2017 at 12:53:28AM -0700, Leon Luo wrote:
> The binding file for imx274 CMOS sensor V4l2 driver
> 
> Signed-off-by: Leon Luo <[e-mail]>
> ---
> v6:
>  - no changes
> v5:
>  - add 'port' and 'endpoint' information
> v4:
>  - no changes
> v3:
>  - remove redundant properties and references
>  - document 'reg' property
> v2:
>  - no changes
> ---
>  .../devicetree/bindings/media/i2c/imx274.txt       | 33 ++++++++++++++++++++++
>  1 file changed, 33 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/imx274.txt

Please add acks when posting new versions.

Rob

Patch

diff --git a/Documentation/devicetree/bindings/media/i2c/imx274.txt b/Documentation/devicetree/bindings/media/i2c/imx274.txt
new file mode 100644
index 000000000000..80f2e89568e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/imx274.txt
@@ -0,0 +1,33 @@ 
+* Sony 1/2.5-Inch 8.51Mp CMOS Digital Image Sensor
+
+The Sony imx274 is a 1/2.5-inch CMOS active pixel digital image sensor with
+an active array size of 3864H x 2202V. It is programmable through I2C
+interface. The I2C address is fixed to 0x1a as per sensor data sheet.
+Image data is sent through MIPI CSI-2, which is configured as 4 lanes
+at 1440 Mbps.
+
+
+Required Properties:
+- compatible: value should be "sony,imx274" for imx274 sensor
+- reg: I2C bus address of the device
+
+Optional Properties:
+- reset-gpios: Sensor reset GPIO
+
+The imx274 device node should contain one 'port' child node with
+an 'endpoint' subnode. For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+	sensor@1a {
+		compatible = "sony,imx274";
+		reg = <0x1a>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reset-gpios = <&gpio_sensor 0 0>;
+		port {
+			sensor_out: endpoint {
+				remote-endpoint = <&csiss_in>;
+			};
+		};
+	};