diff mbox

[v2,2/2] v4l: cadence: Add Cadence MIPI-CSI2 TX driver

Message ID 20180119081547.22312-3-maxime.ripard@free-electrons.com (mailing list archive)
State New, archived
Headers show

Commit Message

Maxime Ripard Jan. 19, 2018, 8:15 a.m. UTC 
The Cadence MIPI-CSI2 TX controller is an hardware block meant to be used
as a bridge between pixel interfaces and a CSI-2 bus.

It supports operating with an internal or external D-PHY, with up to 4
lanes, or without any D-PHY. The current code only supports the former
case.

While the virtual channel input on the pixel interface can be directly
mapped to CSI2, the datatype input is actually a selection signal (3-bits)
mapping to a table of up to 8 preconfigured datatypes/formats (programmed
at start-up)

The block supports up to 8 input datatypes.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 drivers/media/platform/cadence/Kconfig       |   6 +
 drivers/media/platform/cadence/Makefile      |   1 +
 drivers/media/platform/cadence/cdns-csi2tx.c | 586 +++++++++++++++++++++++++++
 3 files changed, 593 insertions(+)
 create mode 100644 drivers/media/platform/cadence/cdns-csi2tx.c

Comments

Benoit Parrot Jan. 29, 2018, 7:30 p.m. UTC | #1 
Maxime,

Thank you for the patch.

Maxime Ripard <maxime.ripard@free-electrons.com> wrote on Fri [2018-Jan-19 09:15:47 +0100]:
> The Cadence MIPI-CSI2 TX controller is an hardware block meant to be used
> as a bridge between pixel interfaces and a CSI-2 bus.
> 
> It supports operating with an internal or external D-PHY, with up to 4
> lanes, or without any D-PHY. The current code only supports the former
> case.
> 
> While the virtual channel input on the pixel interface can be directly
> mapped to CSI2, the datatype input is actually a selection signal (3-bits)
> mapping to a table of up to 8 preconfigured datatypes/formats (programmed
> at start-up)
> 
> The block supports up to 8 input datatypes.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> ---
>  drivers/media/platform/cadence/Kconfig       |   6 +
>  drivers/media/platform/cadence/Makefile      |   1 +
>  drivers/media/platform/cadence/cdns-csi2tx.c | 586 +++++++++++++++++++++++++++
>  3 files changed, 593 insertions(+)
>  create mode 100644 drivers/media/platform/cadence/cdns-csi2tx.c
> 
> diff --git a/drivers/media/platform/cadence/Kconfig b/drivers/media/platform/cadence/Kconfig
> index d1b6bbb6a0eb..db49328ee8b2 100644
> --- a/drivers/media/platform/cadence/Kconfig
> +++ b/drivers/media/platform/cadence/Kconfig
> @@ -9,4 +9,10 @@ config VIDEO_CADENCE_CSI2RX
>  	depends on VIDEO_V4L2_SUBDEV_API
>  	select V4L2_FWNODE
>  
> +config VIDEO_CADENCE_CSI2TX
> +	tristate "Cadence MIPI-CSI2 TX Controller"
> +	depends on MEDIA_CONTROLLER
> +	depends on VIDEO_V4L2_SUBDEV_API
> +	select V4L2_FWNODE
> +
>  endif
> diff --git a/drivers/media/platform/cadence/Makefile b/drivers/media/platform/cadence/Makefile
> index 99a4086b7448..7fe992273162 100644
> --- a/drivers/media/platform/cadence/Makefile
> +++ b/drivers/media/platform/cadence/Makefile
> @@ -1 +1,2 @@
>  obj-$(CONFIG_VIDEO_CADENCE_CSI2RX)	+= cdns-csi2rx.o
> +obj-$(CONFIG_VIDEO_CADENCE_CSI2TX)	+= cdns-csi2tx.o
> diff --git a/drivers/media/platform/cadence/cdns-csi2tx.c b/drivers/media/platform/cadence/cdns-csi2tx.c
> new file mode 100644
> index 000000000000..850701020836
> --- /dev/null
> +++ b/drivers/media/platform/cadence/cdns-csi2tx.c
> @@ -0,0 +1,586 @@
> +/*
> + * Driver for Cadence MIPI-CSI2 TX Controller
> + *
> + * Copyright (C) 2017 Cadence Design Systems Inc.
> + *
> + * This program is free software; you can redistribute  it and/or modify it
> + * under  the terms of  the GNU General  Public License as published by the
> + * Free Software Foundation;  either version 2 of the  License, or (at your
> + * option) any later version.

Should use SPDX license tag line instead.

> + */
> +
> +#include <linux/atomic.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_graph.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-device.h>
> +#include <media/v4l2-fwnode.h>
> +#include <media/v4l2-subdev.h>
> +
> +#define CSI2TX_DEVICE_CONFIG_REG	0x00
> +
> +#define CSI2TX_CONFIG_REG		0x20
> +#define CSI2TX_CONFIG_CFG_REQ			BIT(2)
> +#define CSI2TX_CONFIG_SRST_REQ			BIT(1)
> +
> +#define CSI2TX_DPHY_CFG_REG		0x28
> +#define CSI2TX_DPHY_CFG_CLK_RESET		BIT(16)
> +#define CSI2TX_DPHY_CFG_LANE_RESET(n)		BIT((n) + 12)
> +#define CSI2TX_DPHY_CFG_MODE_MASK		GENMASK(9, 8)
> +#define CSI2TX_DPHY_CFG_MODE_LPDT		(2 << 8)
> +#define CSI2TX_DPHY_CFG_MODE_HS			(1 << 8)
> +#define CSI2TX_DPHY_CFG_MODE_ULPS		(0 << 8)
> +#define CSI2TX_DPHY_CFG_CLK_ENABLE		BIT(4)
> +#define CSI2TX_DPHY_CFG_LANE_ENABLE(n)		BIT(n)
> +
> +#define CSI2TX_DPHY_CLK_WAKEUP_REG	0x2c
> +#define CSI2TX_DPHY_CLK_WAKEUP_ULPS_CYCLES(n)	((n) & 0xffff)
> +
> +#define CSI2TX_DT_CFG_REG(n)		(0x80 + (n) * 8)
> +#define CSI2TX_DT_CFG_DT(n)			(((n) & 0x3f) << 2)
> +
> +#define CSI2TX_DT_FORMAT_REG(n)		(0x84 + (n) * 8)
> +#define CSI2TX_DT_FORMAT_BYTES_PER_LINE(n)	(((n) & 0xffff) << 16)
> +#define CSI2TX_DT_FORMAT_MAX_LINE_NUM(n)	((n) & 0xffff)
> +
> +#define CSI2TX_STREAM_IF_CFG_REG(n)	(0x100 + (n) * 4)
> +#define CSI2TX_STREAM_IF_CFG_FILL_LEVEL(n)	((n) & 0x1f)
> +
> +#define CSI2TX_STREAMS_MAX	4
> +
> +enum csi2tx_pads {
> +	CSI2TX_PAD_SOURCE,
> +	CSI2TX_PAD_SINK_STREAM0,
> +	CSI2TX_PAD_SINK_STREAM1,
> +	CSI2TX_PAD_SINK_STREAM2,
> +	CSI2TX_PAD_SINK_STREAM3,
> +	CSI2TX_PAD_MAX,
> +};
> +
> +struct csi2tx_fmt {
> +	u32	mbus;
> +	u32	dt;
> +	u32	bpp;
> +};
> +
> +struct csi2tx_priv {
> +	struct device			*dev;
> +	atomic_t			count;
> +
> +	void __iomem			*base;
> +
> +	struct clk			*esc_clk;
> +	struct clk			*p_clk;
> +	struct clk			*pixel_clk[CSI2TX_STREAMS_MAX];
> +
> +	struct v4l2_subdev		subdev;
> +	struct v4l2_async_notifier	notifier;
> +	struct media_pad		pads[CSI2TX_PAD_MAX];
> +	struct v4l2_mbus_framefmt	pad_fmts[CSI2TX_PAD_MAX];
> +
> +	bool				has_internal_dphy;
> +	unsigned int			lanes;
> +	unsigned int			max_lanes;

So if I understand this correctly the actual lane number list
specified in DT is not actually used? And so the lane numbers are only
derived from the current numbers of lanes specified.

Meaning the following would produce identical setup:
	csi2tx_out: endpoint {
		remote-endpoint = <&remote_in>;
		clock-lanes = <0>;
		data-lanes = <1 2>;
	};

or
	csi2tx_out: endpoint {
		remote-endpoint = <&remote_in>;
		clock-lanes = <0>;
		data-lanes = <2 3>;
	};

But they would be interpreted differently by say the CSI2-RX side, no?

> +	unsigned int			max_streams;
> +
> +	/* Remote source */
> +	struct v4l2_async_subdev	asd;
> +	struct v4l2_subdev		*sink_subdev;
> +	int				sink_pad;
> +};
> +
> +static const struct csi2tx_fmt csi2tx_formats[] = {
> +	{
> +		.mbus	= MEDIA_BUS_FMT_UYVY8_1X16,
> +		.bpp	= 2,
> +		.dt	= 0x1e,
> +	},
> +	{
> +		.mbus	= MEDIA_BUS_FMT_RGB888_1X24,
> +		.bpp	= 3,
> +		.dt	= 0x24,
> +	},
> +};
> +
> +static const struct v4l2_mbus_framefmt fmt_default = {
> +	.width		= 320,
> +	.height		= 180,
> +	.code		= MEDIA_BUS_FMT_RGB888_1X24,
> +	.field		= V4L2_FIELD_NONE,
> +	.colorspace	= V4L2_COLORSPACE_DEFAULT,
> +};
> +
> +static inline
> +struct csi2tx_priv *v4l2_subdev_to_csi2tx(struct v4l2_subdev *subdev)
> +{
> +	return container_of(subdev, struct csi2tx_priv, subdev);
> +}
> +
> +static int csi2tx_init_cfg(struct v4l2_subdev *subdev,
> +			   struct v4l2_subdev_pad_config *cfg)
> +{
> +	struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
> +	unsigned int i;
> +
> +	for (i = 0; i < subdev->entity.num_pads; i++)
> +		csi2tx->pad_fmts[i] = fmt_default;
> +
> +	return 0;
> +}
> +
> +static const struct csi2tx_fmt *csitx_get_fmt_from_mbus(struct v4l2_mbus_framefmt *mfmt)
> +{
> +	int i;
> +
> +	if (!mfmt)
> +		return NULL;
> +
> +	for (i = 0; i < ARRAY_SIZE(csi2tx_formats); i++)
> +		if (csi2tx_formats[i].mbus == mfmt->code)
> +			return &csi2tx_formats[i];
> +
> +	return NULL;
> +}
> +
> +static int csi2tx_enum_mbus_code(struct v4l2_subdev *subdev,
> +				 struct v4l2_subdev_pad_config *cfg,
> +				 struct v4l2_subdev_mbus_code_enum *code)
> +{
> +	if (code->pad || code->index >= ARRAY_SIZE(csi2tx_formats))
> +		return -EINVAL;
> +
> +	code->code = csi2tx_formats[code->index].mbus;
> +
> +	return 0;
> +}
> +
> +static int csi2tx_get_pad_format(struct v4l2_subdev *subdev,
> +				 struct v4l2_subdev_pad_config *cfg,
> +				 struct v4l2_subdev_format *fmt)
> +{
> +	struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
> +
> +	fmt->format = csi2tx->pad_fmts[fmt->pad];
> +
> +	return 0;
> +}
> +
> +static int csi2tx_set_pad_format(struct v4l2_subdev *subdev,
> +				 struct v4l2_subdev_pad_config *cfg,
> +				 struct v4l2_subdev_format *fmt)
> +{
> +	struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
> +
> +	csi2tx->pad_fmts[fmt->pad] = fmt->format;
> +
> +	return 0;
> +}
> +
> +static const struct v4l2_subdev_pad_ops csi2tx_pad_ops = {
> +	.enum_mbus_code	= csi2tx_enum_mbus_code,
> +	.get_fmt	= csi2tx_get_pad_format,
> +	.init_cfg	= csi2tx_init_cfg,
> +	.set_fmt	= csi2tx_set_pad_format,
> +};
> +
> +static void csi2tx_reset(struct csi2tx_priv *csi2tx)
> +{
> +	writel(CSI2TX_CONFIG_SRST_REQ, csi2tx->base + CSI2TX_CONFIG_REG);
> +
> +	usleep_range(10, 20);
> +}
> +
> +static int csi2tx_start(struct csi2tx_priv *csi2tx)
> +{
> +	struct media_entity *entity = &csi2tx->subdev.entity;
> +	struct media_link *link;
> +	u32 reg;
> +	int i;
> +
> +	/*
> +	 * We're not the first users, there's no need to enable the
> +	 * whole controller.
> +	 */
> +	if (atomic_inc_return(&csi2tx->count) > 1)
> +		return 0;
> +
> +	csi2tx_reset(csi2tx);
> +
> +	writel(CSI2TX_CONFIG_CFG_REQ, csi2tx->base + CSI2TX_CONFIG_REG);
> +
> +	usleep_range(10, 20);
> +
> +	writel(CSI2TX_DPHY_CLK_WAKEUP_ULPS_CYCLES(32),
> +	       csi2tx->base + CSI2TX_DPHY_CLK_WAKEUP_REG);
> +
> +	/* Put our lanes (clock and data) out of reset */
> +	reg = CSI2TX_DPHY_CFG_CLK_RESET | CSI2TX_DPHY_CFG_MODE_LPDT;
> +	for (i = 0; i < csi2tx->lanes; i++)
> +		reg |= CSI2TX_DPHY_CFG_LANE_RESET(i);
> +	writel(reg, csi2tx->base + CSI2TX_DPHY_CFG_REG);
> +
> +	usleep_range(10, 20);
> +
> +	/* Enable our (clock and data) lanes */
> +	reg |= CSI2TX_DPHY_CFG_CLK_ENABLE;
> +	for (i = 0; i < csi2tx->lanes; i++)
> +		reg |= CSI2TX_DPHY_CFG_LANE_ENABLE(i);
> +	writel(reg, csi2tx->base + CSI2TX_DPHY_CFG_REG);
> +
> +	usleep_range(10, 20);
> +
> +	/* Switch to HS mode */
> +	reg &= ~CSI2TX_DPHY_CFG_MODE_MASK;
> +	writel(reg | CSI2TX_DPHY_CFG_MODE_HS,
> +	       csi2tx->base + CSI2TX_DPHY_CFG_REG);
> +
> +	usleep_range(10, 20);
> +
> +	/*
> +	 * Create a static mapping between the CSI virtual channels
> +	 * and the input streams.
> +	 *
> +	 * This should be enhanced, but v4l2 lacks the support for
> +	 * changing that mapping dynamically at the moment.
> +	 */
> +	list_for_each_entry(link, &entity->links, list) {
> +		struct v4l2_mbus_framefmt *mfmt;
> +		const struct csi2tx_fmt *fmt;
> +		unsigned int stream;
> +		int pad_idx = -1;
> +
> +		/* Only consider our enabled input pads */
> +		for (i = CSI2TX_PAD_SINK_STREAM0; i < CSI2TX_PAD_MAX; i++) {
> +			struct media_pad *pad = &csi2tx->pads[i];
> +
> +			if ((pad == link->sink) &&
> +			    (link->flags & MEDIA_LNK_FL_ENABLED)) {
> +				pad_idx = i;
> +				break;
> +			}
> +		}
> +
> +		if (pad_idx < 0)
> +			continue;
> +
> +		mfmt = &csi2tx->pad_fmts[i];
> +		fmt = csitx_get_fmt_from_mbus(mfmt);
> +		stream = pad_idx - CSI2TX_PAD_SINK_STREAM0;
> +
> +		/*
> +		 * We use the stream ID there, but it's wrong.
> +		 *
> +		 * A stream could very well send a data type that is
> +		 * not equal to its stream ID. We need to find a
> +		 * proper way to address it.
> +		 */
> +		writel(CSI2TX_DT_CFG_DT(fmt->dt),
> +		       csi2tx->base + CSI2TX_DT_CFG_REG(stream));
> +
> +		writel(CSI2TX_DT_FORMAT_BYTES_PER_LINE(mfmt->width * fmt->bpp) |
> +		       CSI2TX_DT_FORMAT_MAX_LINE_NUM(mfmt->height + 1),
> +		       csi2tx->base + CSI2TX_DT_FORMAT_REG(stream));
> +
> +		/*
> +		 * TODO: This needs to be calculated based on the
> +		 * output CSI2 clock rate.
> +		 */
> +		writel(CSI2TX_STREAM_IF_CFG_FILL_LEVEL(4),
> +		       csi2tx->base + CSI2TX_STREAM_IF_CFG_REG(stream));
> +	}
> +
> +	/* Disable the configuration mode */
> +	writel(0, csi2tx->base + CSI2TX_CONFIG_REG);
> +
> +	return v4l2_subdev_call(csi2tx->sink_subdev, video, s_stream, true);
> +}
> +
> +static int csi2tx_stop(struct csi2tx_priv *csi2tx)
> +{
> +	/*
> +	 * Let the last user turn off the lights
> +	 */
> +	if (!atomic_dec_and_test(&csi2tx->count))
> +		return 0;
> +
> +	writel(CSI2TX_CONFIG_CFG_REQ | CSI2TX_CONFIG_SRST_REQ,
> +	       csi2tx->base + CSI2TX_CONFIG_REG);
> +
> +	return 0;
> +}
> +
> +static int csi2tx_s_stream(struct v4l2_subdev *subdev, int enable)
> +{
> +	struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
> +	int ret;
> +
> +	if (enable)
> +		ret = csi2tx_start(csi2tx);
> +	else
> +		ret = csi2tx_stop(csi2tx);
> +
> +	return ret;
> +}
> +
> +static const struct v4l2_subdev_video_ops csi2tx_video_ops = {
> +	.s_stream	= csi2tx_s_stream,
> +};
> +
> +static const struct v4l2_subdev_ops csi2tx_subdev_ops = {
> +	.pad		= &csi2tx_pad_ops,
> +	.video		= &csi2tx_video_ops,
> +};
> +
> +static int csi2tx_async_bound(struct v4l2_async_notifier *notifier,
> +			      struct v4l2_subdev *s_subdev,
> +			      struct v4l2_async_subdev *asd)
> +{
> +	struct v4l2_subdev *subdev = notifier->sd;
> +	struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
> +
> +	csi2tx->sink_pad = media_entity_get_fwnode_pad(&s_subdev->entity,
> +						       s_subdev->fwnode,
> +						       MEDIA_PAD_FL_SINK);
> +	if (csi2tx->sink_pad < 0) {
> +		dev_err(csi2tx->dev, "Couldn't find input pad for subdev %s\n",
> +			s_subdev->name);
> +		return csi2tx->sink_pad;
> +	}
> +
> +	csi2tx->sink_subdev = s_subdev;
> +
> +	dev_dbg(csi2tx->dev, "Bound %s pad: %d\n", s_subdev->name,
> +		csi2tx->sink_pad);
> +
> +	return media_create_pad_link(&csi2tx->sink_subdev->entity,
> +				     csi2tx->sink_pad,
> +				     &csi2tx->subdev.entity, 0,
> +				     MEDIA_LNK_FL_ENABLED |
> +				     MEDIA_LNK_FL_IMMUTABLE);
> +}
> +
> +static const struct v4l2_async_notifier_operations csi2tx_notifier_ops = {
> +	.bound		= csi2tx_async_bound,
> +};
> +
> +static int csi2tx_get_resources(struct csi2tx_priv *csi2tx,
> +				struct platform_device *pdev)
> +{
> +	struct resource *res;
> +	u32 reg;
> +	int i;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	csi2tx->base = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(csi2tx->base)) {
> +		dev_err(&pdev->dev, "Couldn't map our registers\n");
> +		return PTR_ERR(csi2tx->base);
> +	}
> +
> +	csi2tx->p_clk = devm_clk_get(&pdev->dev, "p_clk");
> +	if (IS_ERR(csi2tx->p_clk)) {
> +		dev_err(&pdev->dev, "Couldn't get p_clk\n");
> +		return PTR_ERR(csi2tx->p_clk);
> +	}
> +
> +	csi2tx->esc_clk = devm_clk_get(&pdev->dev, "esc_clk");
> +	if (IS_ERR(csi2tx->esc_clk)) {
> +		dev_err(&pdev->dev, "Couldn't get the esc_clk\n");
> +		return PTR_ERR(csi2tx->esc_clk);
> +	}
> +
> +	clk_prepare_enable(csi2tx->p_clk);
> +	reg = readl(csi2tx->base + CSI2TX_DEVICE_CONFIG_REG);
> +	clk_disable_unprepare(csi2tx->p_clk);
> +
> +	csi2tx->max_lanes = (reg & 7);
> +	if (csi2tx->max_lanes > 4) {
> +		dev_err(&pdev->dev, "Invalid number of lanes: %u\n",
> +			csi2tx->max_lanes);
> +		return -EINVAL;
> +	}
> +
> +	csi2tx->max_streams = ((reg >> 4) & 7);
> +	if (csi2tx->max_streams > CSI2TX_STREAMS_MAX) {
> +		dev_err(&pdev->dev, "Invalid number of streams: %u\n",
> +			csi2tx->max_streams);
> +		return -EINVAL;
> +	}
> +
> +	csi2tx->has_internal_dphy = (reg & BIT(3)) ? true : false;
> +
> +	for (i = 0; i < csi2tx->max_streams; i++) {
> +		char clk_name[16];
> +
> +		snprintf(clk_name, sizeof(clk_name), "pixel_if%u_clk", i);
> +		csi2tx->pixel_clk[i] = devm_clk_get(&pdev->dev, clk_name);
> +		if (IS_ERR(csi2tx->pixel_clk[i])) {
> +			dev_err(&pdev->dev, "Couldn't get clock %s\n",
> +				clk_name);
> +			return PTR_ERR(csi2tx->pixel_clk[i]);
> +		}
> +	}
> +
> +	return 0;
> +}
> +
> +static int csi2tx_get_num_lanes(struct device *dev)
> +{
> +	struct v4l2_fwnode_endpoint v4l2_ep;
> +	struct device_node *ep;
> +	int ret;
> +
> +	ep = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0);
> +	if (!ep)
> +		return -EINVAL;
> +
> +	ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &v4l2_ep);
> +	if (ret) {
> +		dev_err(dev, "Could not parse v4l2 endpoint\n");
> +		goto out;
> +	}
> +
> +	if (v4l2_ep.bus_type != V4L2_MBUS_CSI2) {
> +		dev_err(dev, "Unsupported media bus type: 0x%x\n",
> +			v4l2_ep.bus_type);
> +		ret = -EINVAL;
> +		goto out;
> +	}
> +
> +	ret = v4l2_ep.bus.mipi_csi2.num_data_lanes;
> +
> +out:
> +	of_node_put(ep);
> +	return ret;
> +}
> +
> +static int csi2tx_parse_dt(struct csi2tx_priv *csi2tx)
> +{
> +	struct fwnode_handle *fwh;
> +	struct device_node *ep;
> +
> +	ep = of_graph_get_endpoint_by_regs(csi2tx->dev->of_node, 0, 0);
> +	if (!ep)
> +		return -EINVAL;
> +
> +	fwh = of_fwnode_handle(ep);
> +	csi2tx->asd.match.fwnode.fwnode = fwnode_graph_get_remote_port_parent(fwh);
> +	csi2tx->asd.match_type = V4L2_ASYNC_MATCH_FWNODE;
> +	of_node_put(ep);
> +
> +	csi2tx->notifier.subdevs = devm_kzalloc(csi2tx->dev,
> +						sizeof(*csi2tx->notifier.subdevs),
> +						GFP_KERNEL);
> +	if (!csi2tx->notifier.subdevs)
> +		return -ENOMEM;
> +
> +	csi2tx->notifier.subdevs[0] = &csi2tx->asd;
> +	csi2tx->notifier.num_subdevs = 1;
> +	csi2tx->notifier.ops = &csi2tx_notifier_ops;
> +
> +	return v4l2_async_subdev_notifier_register(&csi2tx->subdev,
> +						   &csi2tx->notifier);
> +}
> +
> +static int csi2tx_probe(struct platform_device *pdev)
> +{
> +	struct csi2tx_priv *csi2tx;
> +	int i, ret;
> +
> +	csi2tx = kzalloc(sizeof(*csi2tx), GFP_KERNEL);
> +	if (!csi2tx)
> +		return -ENOMEM;
> +	platform_set_drvdata(pdev, csi2tx);
> +	csi2tx->dev = &pdev->dev;
> +
> +	ret = csi2tx_get_resources(csi2tx, pdev);
> +	if (ret)
> +		goto err_free_priv;
> +
> +	ret = csi2tx_parse_dt(csi2tx);
> +	if (ret)
> +		goto err_free_priv;
> +
> +	v4l2_subdev_init(&csi2tx->subdev, &csi2tx_subdev_ops);
> +	csi2tx->subdev.owner = THIS_MODULE;
> +	csi2tx->subdev.dev = &pdev->dev;
> +	csi2tx->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> +	v4l2_set_subdevdata(&csi2tx->subdev, &pdev->dev);
> +	snprintf(csi2tx->subdev.name, V4L2_SUBDEV_NAME_SIZE, "%s.%s",
> +		 KBUILD_MODNAME, dev_name(&pdev->dev));
> +
> +	ret = csi2tx_get_num_lanes(&pdev->dev);
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "Invalid number of lanes, bailing out.\n");
> +		ret = csi2tx->lanes;
> +		goto err_free_priv;
> +	}
> +	csi2tx->lanes = ret;
> +
> +	if (csi2tx->lanes > csi2tx->max_lanes) {
> +		dev_err(&pdev->dev,
> +			"Current configuration uses more lanes than supported\n");
> +		ret = -EINVAL;
> +		goto err_free_priv;
> +	}
> +
> +	/* Create our media pads */
> +	csi2tx->subdev.entity.function = MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER;
> +	csi2tx->pads[CSI2TX_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
> +	for (i = CSI2TX_PAD_SINK_STREAM0; i < CSI2TX_PAD_MAX; i++)
> +		csi2tx->pads[i].flags = MEDIA_PAD_FL_SINK;
> +
> +	ret = media_entity_pads_init(&csi2tx->subdev.entity, CSI2TX_PAD_MAX,
> +				     csi2tx->pads);
> +	if (ret)
> +		goto err_free_priv;
> +
> +	ret = v4l2_async_register_subdev(&csi2tx->subdev);
> +	if (ret < 0)
> +		goto err_free_priv;
> +
> +	dev_info(&pdev->dev,
> +		 "Probed CSI2TX with %u/%u lanes, %u streams, %s D-PHY\n",
> +		 csi2tx->lanes, csi2tx->max_lanes, csi2tx->max_streams,
> +		 csi2tx->has_internal_dphy ? "internal" : "no");
> +
> +	return 0;
> +
> +err_free_priv:
> +	kfree(csi2tx);
> +	return ret;
> +}
> +
> +static int csi2tx_remove(struct platform_device *pdev)
> +{
> +	struct csi2tx_priv *csi2tx = platform_get_drvdata(pdev);
> +
> +	v4l2_async_unregister_subdev(&csi2tx->subdev);
> +	kfree(csi2tx);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id csi2tx_of_table[] = {
> +	{ .compatible = "cdns,csi2tx" },
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, csi2tx_of_table);
> +
> +static struct platform_driver csi2tx_driver = {
> +	.probe	= csi2tx_probe,
> +	.remove	= csi2tx_remove,
> +
> +	.driver	= {
> +		.name		= "cdns-csi2tx",
> +		.of_match_table	= csi2tx_of_table,
> +	},
> +};
> +module_platform_driver(csi2tx_driver);
> -- 
> 2.14.3
> 

Regards,
Benoit
Maxime Ripard Jan. 30, 2018, 3:36 p.m. UTC | #2 
Hi Benoit,

On Mon, Jan 29, 2018 at 01:30:46PM -0600, Benoit Parrot wrote:
> > +++ b/drivers/media/platform/cadence/cdns-csi2tx.c
> > @@ -0,0 +1,586 @@
> > +/*
> > + * Driver for Cadence MIPI-CSI2 TX Controller
> > + *
> > + * Copyright (C) 2017 Cadence Design Systems Inc.
> > + *
> > + * This program is free software; you can redistribute  it and/or modify it
> > + * under  the terms of  the GNU General  Public License as published by the
> > + * Free Software Foundation;  either version 2 of the  License, or (at your
> > + * option) any later version.
> 
> Should use SPDX license tag line instead.

Indeed.

> > +struct csi2tx_priv {
> > +	struct device			*dev;
> > +	atomic_t			count;
> > +
> > +	void __iomem			*base;
> > +
> > +	struct clk			*esc_clk;
> > +	struct clk			*p_clk;
> > +	struct clk			*pixel_clk[CSI2TX_STREAMS_MAX];
> > +
> > +	struct v4l2_subdev		subdev;
> > +	struct v4l2_async_notifier	notifier;
> > +	struct media_pad		pads[CSI2TX_PAD_MAX];
> > +	struct v4l2_mbus_framefmt	pad_fmts[CSI2TX_PAD_MAX];
> > +
> > +	bool				has_internal_dphy;
> > +	unsigned int			lanes;
> > +	unsigned int			max_lanes;
> 
> So if I understand this correctly the actual lane number list
> specified in DT is not actually used? And so the lane numbers are only
> derived from the current numbers of lanes specified.
> 
> Meaning the following would produce identical setup:
> 	csi2tx_out: endpoint {
> 		remote-endpoint = <&remote_in>;
> 		clock-lanes = <0>;
> 		data-lanes = <1 2>;
> 	};
> 
> or
> 	csi2tx_out: endpoint {
> 		remote-endpoint = <&remote_in>;
> 		clock-lanes = <0>;
> 		data-lanes = <2 3>;
> 	};
> 
> But they would be interpreted differently by say the CSI2-RX side, no?

Ah, right, I should totally fix that.

I'll send a new version shortly.

Thanks!
Maxime
diff mbox

Patch

diff --git a/drivers/media/platform/cadence/Kconfig b/drivers/media/platform/cadence/Kconfig
index d1b6bbb6a0eb..db49328ee8b2 100644
--- a/drivers/media/platform/cadence/Kconfig
+++ b/drivers/media/platform/cadence/Kconfig
@@ -9,4 +9,10 @@  config VIDEO_CADENCE_CSI2RX
 	depends on VIDEO_V4L2_SUBDEV_API
 	select V4L2_FWNODE
 
+config VIDEO_CADENCE_CSI2TX
+	tristate "Cadence MIPI-CSI2 TX Controller"
+	depends on MEDIA_CONTROLLER
+	depends on VIDEO_V4L2_SUBDEV_API
+	select V4L2_FWNODE
+
 endif
diff --git a/drivers/media/platform/cadence/Makefile b/drivers/media/platform/cadence/Makefile
index 99a4086b7448..7fe992273162 100644
--- a/drivers/media/platform/cadence/Makefile
+++ b/drivers/media/platform/cadence/Makefile
@@ -1 +1,2 @@ 
 obj-$(CONFIG_VIDEO_CADENCE_CSI2RX)	+= cdns-csi2rx.o
+obj-$(CONFIG_VIDEO_CADENCE_CSI2TX)	+= cdns-csi2tx.o
diff --git a/drivers/media/platform/cadence/cdns-csi2tx.c b/drivers/media/platform/cadence/cdns-csi2tx.c
new file mode 100644
index 000000000000..850701020836
--- /dev/null
+++ b/drivers/media/platform/cadence/cdns-csi2tx.c
@@ -0,0 +1,586 @@ 
+/*
+ * Driver for Cadence MIPI-CSI2 TX Controller
+ *
+ * Copyright (C) 2017 Cadence Design Systems Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/atomic.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_graph.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-subdev.h>
+
+#define CSI2TX_DEVICE_CONFIG_REG	0x00
+
+#define CSI2TX_CONFIG_REG		0x20
+#define CSI2TX_CONFIG_CFG_REQ			BIT(2)
+#define CSI2TX_CONFIG_SRST_REQ			BIT(1)
+
+#define CSI2TX_DPHY_CFG_REG		0x28
+#define CSI2TX_DPHY_CFG_CLK_RESET		BIT(16)
+#define CSI2TX_DPHY_CFG_LANE_RESET(n)		BIT((n) + 12)
+#define CSI2TX_DPHY_CFG_MODE_MASK		GENMASK(9, 8)
+#define CSI2TX_DPHY_CFG_MODE_LPDT		(2 << 8)
+#define CSI2TX_DPHY_CFG_MODE_HS			(1 << 8)
+#define CSI2TX_DPHY_CFG_MODE_ULPS		(0 << 8)
+#define CSI2TX_DPHY_CFG_CLK_ENABLE		BIT(4)
+#define CSI2TX_DPHY_CFG_LANE_ENABLE(n)		BIT(n)
+
+#define CSI2TX_DPHY_CLK_WAKEUP_REG	0x2c
+#define CSI2TX_DPHY_CLK_WAKEUP_ULPS_CYCLES(n)	((n) & 0xffff)
+
+#define CSI2TX_DT_CFG_REG(n)		(0x80 + (n) * 8)
+#define CSI2TX_DT_CFG_DT(n)			(((n) & 0x3f) << 2)
+
+#define CSI2TX_DT_FORMAT_REG(n)		(0x84 + (n) * 8)
+#define CSI2TX_DT_FORMAT_BYTES_PER_LINE(n)	(((n) & 0xffff) << 16)
+#define CSI2TX_DT_FORMAT_MAX_LINE_NUM(n)	((n) & 0xffff)
+
+#define CSI2TX_STREAM_IF_CFG_REG(n)	(0x100 + (n) * 4)
+#define CSI2TX_STREAM_IF_CFG_FILL_LEVEL(n)	((n) & 0x1f)
+
+#define CSI2TX_STREAMS_MAX	4
+
+enum csi2tx_pads {
+	CSI2TX_PAD_SOURCE,
+	CSI2TX_PAD_SINK_STREAM0,
+	CSI2TX_PAD_SINK_STREAM1,
+	CSI2TX_PAD_SINK_STREAM2,
+	CSI2TX_PAD_SINK_STREAM3,
+	CSI2TX_PAD_MAX,
+};
+
+struct csi2tx_fmt {
+	u32	mbus;
+	u32	dt;
+	u32	bpp;
+};
+
+struct csi2tx_priv {
+	struct device			*dev;
+	atomic_t			count;
+
+	void __iomem			*base;
+
+	struct clk			*esc_clk;
+	struct clk			*p_clk;
+	struct clk			*pixel_clk[CSI2TX_STREAMS_MAX];
+
+	struct v4l2_subdev		subdev;
+	struct v4l2_async_notifier	notifier;
+	struct media_pad		pads[CSI2TX_PAD_MAX];
+	struct v4l2_mbus_framefmt	pad_fmts[CSI2TX_PAD_MAX];
+
+	bool				has_internal_dphy;
+	unsigned int			lanes;
+	unsigned int			max_lanes;
+	unsigned int			max_streams;
+
+	/* Remote source */
+	struct v4l2_async_subdev	asd;
+	struct v4l2_subdev		*sink_subdev;
+	int				sink_pad;
+};
+
+static const struct csi2tx_fmt csi2tx_formats[] = {
+	{
+		.mbus	= MEDIA_BUS_FMT_UYVY8_1X16,
+		.bpp	= 2,
+		.dt	= 0x1e,
+	},
+	{
+		.mbus	= MEDIA_BUS_FMT_RGB888_1X24,
+		.bpp	= 3,
+		.dt	= 0x24,
+	},
+};
+
+static const struct v4l2_mbus_framefmt fmt_default = {
+	.width		= 320,
+	.height		= 180,
+	.code		= MEDIA_BUS_FMT_RGB888_1X24,
+	.field		= V4L2_FIELD_NONE,
+	.colorspace	= V4L2_COLORSPACE_DEFAULT,
+};
+
+static inline
+struct csi2tx_priv *v4l2_subdev_to_csi2tx(struct v4l2_subdev *subdev)
+{
+	return container_of(subdev, struct csi2tx_priv, subdev);
+}
+
+static int csi2tx_init_cfg(struct v4l2_subdev *subdev,
+			   struct v4l2_subdev_pad_config *cfg)
+{
+	struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
+	unsigned int i;
+
+	for (i = 0; i < subdev->entity.num_pads; i++)
+		csi2tx->pad_fmts[i] = fmt_default;
+
+	return 0;
+}
+
+static const struct csi2tx_fmt *csitx_get_fmt_from_mbus(struct v4l2_mbus_framefmt *mfmt)
+{
+	int i;
+
+	if (!mfmt)
+		return NULL;
+
+	for (i = 0; i < ARRAY_SIZE(csi2tx_formats); i++)
+		if (csi2tx_formats[i].mbus == mfmt->code)
+			return &csi2tx_formats[i];
+
+	return NULL;
+}
+
+static int csi2tx_enum_mbus_code(struct v4l2_subdev *subdev,
+				 struct v4l2_subdev_pad_config *cfg,
+				 struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad || code->index >= ARRAY_SIZE(csi2tx_formats))
+		return -EINVAL;
+
+	code->code = csi2tx_formats[code->index].mbus;
+
+	return 0;
+}
+
+static int csi2tx_get_pad_format(struct v4l2_subdev *subdev,
+				 struct v4l2_subdev_pad_config *cfg,
+				 struct v4l2_subdev_format *fmt)
+{
+	struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
+
+	fmt->format = csi2tx->pad_fmts[fmt->pad];
+
+	return 0;
+}
+
+static int csi2tx_set_pad_format(struct v4l2_subdev *subdev,
+				 struct v4l2_subdev_pad_config *cfg,
+				 struct v4l2_subdev_format *fmt)
+{
+	struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
+
+	csi2tx->pad_fmts[fmt->pad] = fmt->format;
+
+	return 0;
+}
+
+static const struct v4l2_subdev_pad_ops csi2tx_pad_ops = {
+	.enum_mbus_code	= csi2tx_enum_mbus_code,
+	.get_fmt	= csi2tx_get_pad_format,
+	.init_cfg	= csi2tx_init_cfg,
+	.set_fmt	= csi2tx_set_pad_format,
+};
+
+static void csi2tx_reset(struct csi2tx_priv *csi2tx)
+{
+	writel(CSI2TX_CONFIG_SRST_REQ, csi2tx->base + CSI2TX_CONFIG_REG);
+
+	usleep_range(10, 20);
+}
+
+static int csi2tx_start(struct csi2tx_priv *csi2tx)
+{
+	struct media_entity *entity = &csi2tx->subdev.entity;
+	struct media_link *link;
+	u32 reg;
+	int i;
+
+	/*
+	 * We're not the first users, there's no need to enable the
+	 * whole controller.
+	 */
+	if (atomic_inc_return(&csi2tx->count) > 1)
+		return 0;
+
+	csi2tx_reset(csi2tx);
+
+	writel(CSI2TX_CONFIG_CFG_REQ, csi2tx->base + CSI2TX_CONFIG_REG);
+
+	usleep_range(10, 20);
+
+	writel(CSI2TX_DPHY_CLK_WAKEUP_ULPS_CYCLES(32),
+	       csi2tx->base + CSI2TX_DPHY_CLK_WAKEUP_REG);
+
+	/* Put our lanes (clock and data) out of reset */
+	reg = CSI2TX_DPHY_CFG_CLK_RESET | CSI2TX_DPHY_CFG_MODE_LPDT;
+	for (i = 0; i < csi2tx->lanes; i++)
+		reg |= CSI2TX_DPHY_CFG_LANE_RESET(i);
+	writel(reg, csi2tx->base + CSI2TX_DPHY_CFG_REG);
+
+	usleep_range(10, 20);
+
+	/* Enable our (clock and data) lanes */
+	reg |= CSI2TX_DPHY_CFG_CLK_ENABLE;
+	for (i = 0; i < csi2tx->lanes; i++)
+		reg |= CSI2TX_DPHY_CFG_LANE_ENABLE(i);
+	writel(reg, csi2tx->base + CSI2TX_DPHY_CFG_REG);
+
+	usleep_range(10, 20);
+
+	/* Switch to HS mode */
+	reg &= ~CSI2TX_DPHY_CFG_MODE_MASK;
+	writel(reg | CSI2TX_DPHY_CFG_MODE_HS,
+	       csi2tx->base + CSI2TX_DPHY_CFG_REG);
+
+	usleep_range(10, 20);
+
+	/*
+	 * Create a static mapping between the CSI virtual channels
+	 * and the input streams.
+	 *
+	 * This should be enhanced, but v4l2 lacks the support for
+	 * changing that mapping dynamically at the moment.
+	 */
+	list_for_each_entry(link, &entity->links, list) {
+		struct v4l2_mbus_framefmt *mfmt;
+		const struct csi2tx_fmt *fmt;
+		unsigned int stream;
+		int pad_idx = -1;
+
+		/* Only consider our enabled input pads */
+		for (i = CSI2TX_PAD_SINK_STREAM0; i < CSI2TX_PAD_MAX; i++) {
+			struct media_pad *pad = &csi2tx->pads[i];
+
+			if ((pad == link->sink) &&
+			    (link->flags & MEDIA_LNK_FL_ENABLED)) {
+				pad_idx = i;
+				break;
+			}
+		}
+
+		if (pad_idx < 0)
+			continue;
+
+		mfmt = &csi2tx->pad_fmts[i];
+		fmt = csitx_get_fmt_from_mbus(mfmt);
+		stream = pad_idx - CSI2TX_PAD_SINK_STREAM0;
+
+		/*
+		 * We use the stream ID there, but it's wrong.
+		 *
+		 * A stream could very well send a data type that is
+		 * not equal to its stream ID. We need to find a
+		 * proper way to address it.
+		 */
+		writel(CSI2TX_DT_CFG_DT(fmt->dt),
+		       csi2tx->base + CSI2TX_DT_CFG_REG(stream));
+
+		writel(CSI2TX_DT_FORMAT_BYTES_PER_LINE(mfmt->width * fmt->bpp) |
+		       CSI2TX_DT_FORMAT_MAX_LINE_NUM(mfmt->height + 1),
+		       csi2tx->base + CSI2TX_DT_FORMAT_REG(stream));
+
+		/*
+		 * TODO: This needs to be calculated based on the
+		 * output CSI2 clock rate.
+		 */
+		writel(CSI2TX_STREAM_IF_CFG_FILL_LEVEL(4),
+		       csi2tx->base + CSI2TX_STREAM_IF_CFG_REG(stream));
+	}
+
+	/* Disable the configuration mode */
+	writel(0, csi2tx->base + CSI2TX_CONFIG_REG);
+
+	return v4l2_subdev_call(csi2tx->sink_subdev, video, s_stream, true);
+}
+
+static int csi2tx_stop(struct csi2tx_priv *csi2tx)
+{
+	/*
+	 * Let the last user turn off the lights
+	 */
+	if (!atomic_dec_and_test(&csi2tx->count))
+		return 0;
+
+	writel(CSI2TX_CONFIG_CFG_REQ | CSI2TX_CONFIG_SRST_REQ,
+	       csi2tx->base + CSI2TX_CONFIG_REG);
+
+	return 0;
+}
+
+static int csi2tx_s_stream(struct v4l2_subdev *subdev, int enable)
+{
+	struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
+	int ret;
+
+	if (enable)
+		ret = csi2tx_start(csi2tx);
+	else
+		ret = csi2tx_stop(csi2tx);
+
+	return ret;
+}
+
+static const struct v4l2_subdev_video_ops csi2tx_video_ops = {
+	.s_stream	= csi2tx_s_stream,
+};
+
+static const struct v4l2_subdev_ops csi2tx_subdev_ops = {
+	.pad		= &csi2tx_pad_ops,
+	.video		= &csi2tx_video_ops,
+};
+
+static int csi2tx_async_bound(struct v4l2_async_notifier *notifier,
+			      struct v4l2_subdev *s_subdev,
+			      struct v4l2_async_subdev *asd)
+{
+	struct v4l2_subdev *subdev = notifier->sd;
+	struct csi2tx_priv *csi2tx = v4l2_subdev_to_csi2tx(subdev);
+
+	csi2tx->sink_pad = media_entity_get_fwnode_pad(&s_subdev->entity,
+						       s_subdev->fwnode,
+						       MEDIA_PAD_FL_SINK);
+	if (csi2tx->sink_pad < 0) {
+		dev_err(csi2tx->dev, "Couldn't find input pad for subdev %s\n",
+			s_subdev->name);
+		return csi2tx->sink_pad;
+	}
+
+	csi2tx->sink_subdev = s_subdev;
+
+	dev_dbg(csi2tx->dev, "Bound %s pad: %d\n", s_subdev->name,
+		csi2tx->sink_pad);
+
+	return media_create_pad_link(&csi2tx->sink_subdev->entity,
+				     csi2tx->sink_pad,
+				     &csi2tx->subdev.entity, 0,
+				     MEDIA_LNK_FL_ENABLED |
+				     MEDIA_LNK_FL_IMMUTABLE);
+}
+
+static const struct v4l2_async_notifier_operations csi2tx_notifier_ops = {
+	.bound		= csi2tx_async_bound,
+};
+
+static int csi2tx_get_resources(struct csi2tx_priv *csi2tx,
+				struct platform_device *pdev)
+{
+	struct resource *res;
+	u32 reg;
+	int i;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	csi2tx->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(csi2tx->base)) {
+		dev_err(&pdev->dev, "Couldn't map our registers\n");
+		return PTR_ERR(csi2tx->base);
+	}
+
+	csi2tx->p_clk = devm_clk_get(&pdev->dev, "p_clk");
+	if (IS_ERR(csi2tx->p_clk)) {
+		dev_err(&pdev->dev, "Couldn't get p_clk\n");
+		return PTR_ERR(csi2tx->p_clk);
+	}
+
+	csi2tx->esc_clk = devm_clk_get(&pdev->dev, "esc_clk");
+	if (IS_ERR(csi2tx->esc_clk)) {
+		dev_err(&pdev->dev, "Couldn't get the esc_clk\n");
+		return PTR_ERR(csi2tx->esc_clk);
+	}
+
+	clk_prepare_enable(csi2tx->p_clk);
+	reg = readl(csi2tx->base + CSI2TX_DEVICE_CONFIG_REG);
+	clk_disable_unprepare(csi2tx->p_clk);
+
+	csi2tx->max_lanes = (reg & 7);
+	if (csi2tx->max_lanes > 4) {
+		dev_err(&pdev->dev, "Invalid number of lanes: %u\n",
+			csi2tx->max_lanes);
+		return -EINVAL;
+	}
+
+	csi2tx->max_streams = ((reg >> 4) & 7);
+	if (csi2tx->max_streams > CSI2TX_STREAMS_MAX) {
+		dev_err(&pdev->dev, "Invalid number of streams: %u\n",
+			csi2tx->max_streams);
+		return -EINVAL;
+	}
+
+	csi2tx->has_internal_dphy = (reg & BIT(3)) ? true : false;
+
+	for (i = 0; i < csi2tx->max_streams; i++) {
+		char clk_name[16];
+
+		snprintf(clk_name, sizeof(clk_name), "pixel_if%u_clk", i);
+		csi2tx->pixel_clk[i] = devm_clk_get(&pdev->dev, clk_name);
+		if (IS_ERR(csi2tx->pixel_clk[i])) {
+			dev_err(&pdev->dev, "Couldn't get clock %s\n",
+				clk_name);
+			return PTR_ERR(csi2tx->pixel_clk[i]);
+		}
+	}
+
+	return 0;
+}
+
+static int csi2tx_get_num_lanes(struct device *dev)
+{
+	struct v4l2_fwnode_endpoint v4l2_ep;
+	struct device_node *ep;
+	int ret;
+
+	ep = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0);
+	if (!ep)
+		return -EINVAL;
+
+	ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &v4l2_ep);
+	if (ret) {
+		dev_err(dev, "Could not parse v4l2 endpoint\n");
+		goto out;
+	}
+
+	if (v4l2_ep.bus_type != V4L2_MBUS_CSI2) {
+		dev_err(dev, "Unsupported media bus type: 0x%x\n",
+			v4l2_ep.bus_type);
+		ret = -EINVAL;
+		goto out;
+	}
+
+	ret = v4l2_ep.bus.mipi_csi2.num_data_lanes;
+
+out:
+	of_node_put(ep);
+	return ret;
+}
+
+static int csi2tx_parse_dt(struct csi2tx_priv *csi2tx)
+{
+	struct fwnode_handle *fwh;
+	struct device_node *ep;
+
+	ep = of_graph_get_endpoint_by_regs(csi2tx->dev->of_node, 0, 0);
+	if (!ep)
+		return -EINVAL;
+
+	fwh = of_fwnode_handle(ep);
+	csi2tx->asd.match.fwnode.fwnode = fwnode_graph_get_remote_port_parent(fwh);
+	csi2tx->asd.match_type = V4L2_ASYNC_MATCH_FWNODE;
+	of_node_put(ep);
+
+	csi2tx->notifier.subdevs = devm_kzalloc(csi2tx->dev,
+						sizeof(*csi2tx->notifier.subdevs),
+						GFP_KERNEL);
+	if (!csi2tx->notifier.subdevs)
+		return -ENOMEM;
+
+	csi2tx->notifier.subdevs[0] = &csi2tx->asd;
+	csi2tx->notifier.num_subdevs = 1;
+	csi2tx->notifier.ops = &csi2tx_notifier_ops;
+
+	return v4l2_async_subdev_notifier_register(&csi2tx->subdev,
+						   &csi2tx->notifier);
+}
+
+static int csi2tx_probe(struct platform_device *pdev)
+{
+	struct csi2tx_priv *csi2tx;
+	int i, ret;
+
+	csi2tx = kzalloc(sizeof(*csi2tx), GFP_KERNEL);
+	if (!csi2tx)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, csi2tx);
+	csi2tx->dev = &pdev->dev;
+
+	ret = csi2tx_get_resources(csi2tx, pdev);
+	if (ret)
+		goto err_free_priv;
+
+	ret = csi2tx_parse_dt(csi2tx);
+	if (ret)
+		goto err_free_priv;
+
+	v4l2_subdev_init(&csi2tx->subdev, &csi2tx_subdev_ops);
+	csi2tx->subdev.owner = THIS_MODULE;
+	csi2tx->subdev.dev = &pdev->dev;
+	csi2tx->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	v4l2_set_subdevdata(&csi2tx->subdev, &pdev->dev);
+	snprintf(csi2tx->subdev.name, V4L2_SUBDEV_NAME_SIZE, "%s.%s",
+		 KBUILD_MODNAME, dev_name(&pdev->dev));
+
+	ret = csi2tx_get_num_lanes(&pdev->dev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Invalid number of lanes, bailing out.\n");
+		ret = csi2tx->lanes;
+		goto err_free_priv;
+	}
+	csi2tx->lanes = ret;
+
+	if (csi2tx->lanes > csi2tx->max_lanes) {
+		dev_err(&pdev->dev,
+			"Current configuration uses more lanes than supported\n");
+		ret = -EINVAL;
+		goto err_free_priv;
+	}
+
+	/* Create our media pads */
+	csi2tx->subdev.entity.function = MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER;
+	csi2tx->pads[CSI2TX_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+	for (i = CSI2TX_PAD_SINK_STREAM0; i < CSI2TX_PAD_MAX; i++)
+		csi2tx->pads[i].flags = MEDIA_PAD_FL_SINK;
+
+	ret = media_entity_pads_init(&csi2tx->subdev.entity, CSI2TX_PAD_MAX,
+				     csi2tx->pads);
+	if (ret)
+		goto err_free_priv;
+
+	ret = v4l2_async_register_subdev(&csi2tx->subdev);
+	if (ret < 0)
+		goto err_free_priv;
+
+	dev_info(&pdev->dev,
+		 "Probed CSI2TX with %u/%u lanes, %u streams, %s D-PHY\n",
+		 csi2tx->lanes, csi2tx->max_lanes, csi2tx->max_streams,
+		 csi2tx->has_internal_dphy ? "internal" : "no");
+
+	return 0;
+
+err_free_priv:
+	kfree(csi2tx);
+	return ret;
+}
+
+static int csi2tx_remove(struct platform_device *pdev)
+{
+	struct csi2tx_priv *csi2tx = platform_get_drvdata(pdev);
+
+	v4l2_async_unregister_subdev(&csi2tx->subdev);
+	kfree(csi2tx);
+
+	return 0;
+}
+
+static const struct of_device_id csi2tx_of_table[] = {
+	{ .compatible = "cdns,csi2tx" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, csi2tx_of_table);
+
+static struct platform_driver csi2tx_driver = {
+	.probe	= csi2tx_probe,
+	.remove	= csi2tx_remove,
+
+	.driver	= {
+		.name		= "cdns-csi2tx",
+		.of_match_table	= csi2tx_of_table,
+	},
+};
+module_platform_driver(csi2tx_driver);