| Message ID | 20180507162152.2545-14-rui.silva@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi, I have a few editing suggestions below... On 05/07/2018 09:21 AM, Rui Miguel Silva wrote: > Add rst document to describe the i.MX7 media driver and also a working example > from the Warp7 board usage with a OV2680 sensor. > > Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> > --- > Documentation/media/v4l-drivers/imx7.rst | 157 ++++++++++++++++++++++ > Documentation/media/v4l-drivers/index.rst | 1 + > 2 files changed, 158 insertions(+) > create mode 100644 Documentation/media/v4l-drivers/imx7.rst > > diff --git a/Documentation/media/v4l-drivers/imx7.rst b/Documentation/media/v4l-drivers/imx7.rst > new file mode 100644 > index 000000000000..64b97b442277 > --- /dev/null > +++ b/Documentation/media/v4l-drivers/imx7.rst > @@ -0,0 +1,157 @@ > +i.MX7 Video Capture Driver > +========================== > + > +Introduction > +------------ > + > +The i.MX7 contrary to the i.MX5/6 family does not contain an Image Processing > +Unit (IPU), because of that the capabilities to perform operations or s/,/;/ > +manipulation of the capture frames is less feature rich. are less > + > +For image capture the i.MX7 have three units: has > +- CMOS Sensor Interface (CSI) > +- Video Multiplexer > +- MIPI CSI-2 Receiver > + > +:: > + |\ > + MIPI Camera Input ---> MIPI CSI-2 --- > | \ > + | \ > + | M | > + | U | ------> CSI ---> Capture > + | X | > + | / > + Parallel Camera Input ----------------> | / > + |/ > + > +For additional information, please refer to the latest versions of the i.MX7 > +reference manual [#f1]_. > + > +Entities > +-------- > + > +imx7-mipi-csi2 > +-------------- > + > +This is the MIPI CSI-2 recevier entity. It has one sink pad to receive the pixel receiver > +data from MIPI CSI-2 camera sensor. It has one source pad, corresponding to the > +virtual channel 0. This module is compliant to previous version of Samsung > +D-phy, and support two D-PHY Rx Data lanes. supports > + > +csi_mux > +------- > + > +This is the video multiplexer. It has two sink pads to select from either camera > +sensors with a parallel interface or from MIPI CSI-2 virtual channel 0. It has sensor > +a single source pad that routes to the CSI. > + > +csi > +--- > + > +The CSI enables the chip to connect directly to external CMOS image sensor. CSI > +can interfaces directly with Parallel and MIPI CSI-2 buses. It has 256 x 64 FIFO interface > +to store received image pixel data and embedded DMA controllers to transfer data > +from the FIFO through AHB bus. > + > +This entity has one sink pad that receive from the csi_mux entity and a single receives > +source pad that route video frames directly to memory buffers, this pad is routes buffers. This pad is > +routed to a capture device node. > + > +Usage Notes > +----------- > + > +To aid in configuration and for backward compatibility with V4L2 applications > +that access controls only from video device nodes, the capture device interfaces > +inherit controls from the active entities in the current pipeline, so controls > +can be accessed either directly from the subdev or from the active capture > +device interface. For example, the sensor controls are available either from the > +sensor subdevs or from the active capture device. > + > +Warp7 with OV2680 > +----------------- > + > +On this platform an OV2680 MIPI CSI-2 module is connected to the internal MIPI > +CSI-2 receiver. The following example configures a video capture pipeline with > +an output of 800x600, and BGGR 10 bit bayer format: > + > +.. code-block:: none > + # Setup links > + media-ctl -l "'ov2680 1-0036':0 -> 'imx7-mipi-csis.0':0[1]" > + media-ctl -l "'imx7-mipi-csis.0':1 -> 'csi_mux':1[1]" > + media-ctl -l "'csi_mux':2 -> 'csi':0[1]" > + media-ctl -l "'csi':1 -> 'csi capture':0[1]" > + > + # Configure pads for pipeline > + media-ctl -V "'ov2680 1-0036':0 [fmt:SBGGR10_1X10/800x600 field:none]" > + media-ctl -V "'csi_mux':1 [fmt:SBGGR10_1X10/800x600 field:none]" > + media-ctl -V "'csi_mux':2 [fmt:SBGGR10_1X10/800x600 field:none]" > + media-ctl -V "'imx7-mipi-csis.0':0 [fmt:SBGGR10_1X10/800x600 field:none]" > + media-ctl -V "'csi':0 [fmt:SBGGR10_1X10/800x600 field:none]" > + > +After this streaming can start, the v4l2-ctl tool can be used to select any of can start. The > +the resolutions supported by the sensor. > + > +.. code-block:: none > + root@imx7s-warp:~# media-ctl -p > + Media controller API version 4.17.0 > + > + Media device information > + ------------------------ > + driver imx-media > + model imx-media > + serial > + bus info > + hw revision 0x0 > + driver version 4.17.0 > + > + Device topology > + - entity 1: csi (2 pads, 2 links) > + type V4L2 subdev subtype Unknown flags 0 > + device node name /dev/v4l-subdev0 > + pad0: Sink > + [fmt:SBGGR10_1X10/800x600 field:none] > + <- "csi_mux":2 [ENABLED] > + pad1: Source > + [fmt:SBGGR10_1X10/800x600 field:none] > + -> "csi capture":0 [ENABLED] > + > + - entity 4: csi capture (1 pad, 1 link) > + type Node subtype V4L flags 0 > + device node name /dev/video0 > + pad0: Sink > + <- "csi":1 [ENABLED] > + > + - entity 10: csi_mux (3 pads, 2 links) > + type V4L2 subdev subtype Unknown flags 0 > + device node name /dev/v4l-subdev1 > + pad0: Sink > + [fmt:unknown/0x0] > + pad1: Sink > + [fmt:unknown/800x600 field:none] > + <- "imx7-mipi-csis.0":1 [ENABLED] > + pad2: Source > + [fmt:unknown/800x600 field:none] > + -> "csi":0 [ENABLED] > + > + - entity 14: imx7-mipi-csis.0 (2 pads, 2 links) > + type V4L2 subdev subtype Unknown flags 0 > + device node name /dev/v4l-subdev2 > + pad0: Sink > + [fmt:SBGGR10_1X10/800x600 field:none] > + <- "ov2680 1-0036":0 [ENABLED] > + pad1: Source > + [fmt:SBGGR10_1X10/800x600 field:none] > + -> "csi_mux":1 [ENABLED] > + > + - entity 17: ov2680 1-0036 (1 pad, 1 link) > + type V4L2 subdev subtype Sensor flags 0 > + device node name /dev/v4l-subdev3 > + pad0: Source > + [fmt:SBGGR10_1X10/800x600 field:none] > + -> "imx7-mipi-csis.0":0 [ENABLED] > + > + > +References > +---------- > + > +.. [#f1] https://www.nxp.com/docs/en/reference-manual/IMX7SRM.pdf thanks.
Hi Randy, On Tue 08 May 2018 at 17:24, Randy Dunlap wrote: > Hi, > > I have a few editing suggestions below... Thank you very much for this. I will incorporate this in the next version. --- Cheers, Rui > > On 05/07/2018 09:21 AM, Rui Miguel Silva wrote: >> Add rst document to describe the i.MX7 media driver and also a >> working example >> from the Warp7 board usage with a OV2680 sensor. >> >> Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> >> --- >> Documentation/media/v4l-drivers/imx7.rst | 157 >> ++++++++++++++++++++++ >> Documentation/media/v4l-drivers/index.rst | 1 + >> 2 files changed, 158 insertions(+) >> create mode 100644 Documentation/media/v4l-drivers/imx7.rst >> >> diff --git a/Documentation/media/v4l-drivers/imx7.rst >> b/Documentation/media/v4l-drivers/imx7.rst >> new file mode 100644 >> index 000000000000..64b97b442277 >> --- /dev/null >> +++ b/Documentation/media/v4l-drivers/imx7.rst >> @@ -0,0 +1,157 @@ >> +i.MX7 Video Capture Driver >> +========================== >> + >> +Introduction >> +------------ >> + >> +The i.MX7 contrary to the i.MX5/6 family does not contain an >> Image Processing >> +Unit (IPU), because of that the capabilities to perform >> operations or > > s/,/;/ > >> +manipulation of the capture frames is less feature rich. > > are less > >> + >> +For image capture the i.MX7 have three units: > > has > >> +- CMOS Sensor Interface (CSI) >> +- Video Multiplexer >> +- MIPI CSI-2 Receiver >> + >> +:: >> + |\ >> + MIPI Camera Input ---> MIPI CSI-2 --- > | \ >> + | \ >> + | M | >> + | U | ------> CSI >> ---> Capture >> + | X | >> + | / >> + Parallel Camera Input ----------------> | / >> + |/ >> + >> +For additional information, please refer to the latest >> versions of the i.MX7 >> +reference manual [#f1]_. >> + >> +Entities >> +-------- >> + >> +imx7-mipi-csi2 >> +-------------- >> + >> +This is the MIPI CSI-2 recevier entity. It has one sink pad to >> receive the pixel > > receiver > >> +data from MIPI CSI-2 camera sensor. It has one source pad, >> corresponding to the >> +virtual channel 0. This module is compliant to previous >> version of Samsung >> +D-phy, and support two D-PHY Rx Data lanes. > > supports > >> + >> +csi_mux >> +------- >> + >> +This is the video multiplexer. It has two sink pads to select >> from either camera >> +sensors with a parallel interface or from MIPI CSI-2 virtual >> channel 0. It has > > sensor > >> +a single source pad that routes to the CSI. >> + >> +csi >> +--- >> + >> +The CSI enables the chip to connect directly to external CMOS >> image sensor. CSI >> +can interfaces directly with Parallel and MIPI CSI-2 buses. It >> has 256 x 64 FIFO > > interface > >> +to store received image pixel data and embedded DMA >> controllers to transfer data >> +from the FIFO through AHB bus. >> + >> +This entity has one sink pad that receive from the csi_mux >> entity and a single > > receives > >> +source pad that route video frames directly to memory buffers, >> this pad is > > routes > buffers. This pad is > >> +routed to a capture device node. >> + >> +Usage Notes >> +----------- >> + >> +To aid in configuration and for backward compatibility with >> V4L2 applications >> +that access controls only from video device nodes, the capture >> device interfaces >> +inherit controls from the active entities in the current >> pipeline, so controls >> +can be accessed either directly from the subdev or from the >> active capture >> +device interface. For example, the sensor controls are >> available either from the >> +sensor subdevs or from the active capture device. >> + >> +Warp7 with OV2680 >> +----------------- >> + >> +On this platform an OV2680 MIPI CSI-2 module is connected to >> the internal MIPI >> +CSI-2 receiver. The following example configures a video >> capture pipeline with >> +an output of 800x600, and BGGR 10 bit bayer format: >> + >> +.. code-block:: none >> + # Setup links >> + media-ctl -l "'ov2680 1-0036':0 -> 'imx7-mipi-csis.0':0[1]" >> + media-ctl -l "'imx7-mipi-csis.0':1 -> 'csi_mux':1[1]" >> + media-ctl -l "'csi_mux':2 -> 'csi':0[1]" >> + media-ctl -l "'csi':1 -> 'csi capture':0[1]" >> + >> + # Configure pads for pipeline >> + media-ctl -V "'ov2680 1-0036':0 [fmt:SBGGR10_1X10/800x600 >> field:none]" >> + media-ctl -V "'csi_mux':1 [fmt:SBGGR10_1X10/800x600 >> field:none]" >> + media-ctl -V "'csi_mux':2 [fmt:SBGGR10_1X10/800x600 >> field:none]" >> + media-ctl -V "'imx7-mipi-csis.0':0 >> [fmt:SBGGR10_1X10/800x600 field:none]" >> + media-ctl -V "'csi':0 [fmt:SBGGR10_1X10/800x600 >> field:none]" >> + >> +After this streaming can start, the v4l2-ctl tool can be used >> to select any of > > can start. The > >> +the resolutions supported by the sensor. >> + >> +.. code-block:: none >> + root@imx7s-warp:~# media-ctl -p >> + Media controller API version 4.17.0 >> + >> + Media device information >> + ------------------------ >> + driver imx-media >> + model imx-media >> + serial >> + bus info >> + hw revision 0x0 >> + driver version 4.17.0 >> + >> + Device topology >> + - entity 1: csi (2 pads, 2 links) >> + type V4L2 subdev subtype Unknown flags 0 >> + device node name /dev/v4l-subdev0 >> + pad0: Sink >> + [fmt:SBGGR10_1X10/800x600 field:none] >> + <- "csi_mux":2 [ENABLED] >> + pad1: Source >> + [fmt:SBGGR10_1X10/800x600 field:none] >> + -> "csi capture":0 [ENABLED] >> + >> + - entity 4: csi capture (1 pad, 1 link) >> + type Node subtype V4L flags 0 >> + device node name /dev/video0 >> + pad0: Sink >> + <- "csi":1 [ENABLED] >> + >> + - entity 10: csi_mux (3 pads, 2 links) >> + type V4L2 subdev subtype Unknown flags 0 >> + device node name /dev/v4l-subdev1 >> + pad0: Sink >> + [fmt:unknown/0x0] >> + pad1: Sink >> + [fmt:unknown/800x600 field:none] >> + <- "imx7-mipi-csis.0":1 [ENABLED] >> + pad2: Source >> + [fmt:unknown/800x600 field:none] >> + -> "csi":0 [ENABLED] >> + >> + - entity 14: imx7-mipi-csis.0 (2 pads, 2 links) >> + type V4L2 subdev subtype Unknown flags 0 >> + device node name /dev/v4l-subdev2 >> + pad0: Sink >> + [fmt:SBGGR10_1X10/800x600 field:none] >> + <- "ov2680 1-0036":0 [ENABLED] >> + pad1: Source >> + [fmt:SBGGR10_1X10/800x600 field:none] >> + -> "csi_mux":1 [ENABLED] >> + >> + - entity 17: ov2680 1-0036 (1 pad, 1 link) >> + type V4L2 subdev subtype Sensor flags 0 >> + device node name /dev/v4l-subdev3 >> + pad0: Source >> + [fmt:SBGGR10_1X10/800x600 field:none] >> + -> "imx7-mipi-csis.0":0 [ENABLED] >> + >> + >> +References >> +---------- >> + >> +.. [#f1] >> https://www.nxp.com/docs/en/reference-manual/IMX7SRM.pdf > > thanks.
diff --git a/Documentation/media/v4l-drivers/imx7.rst b/Documentation/media/v4l-drivers/imx7.rst new file mode 100644 index 000000000000..64b97b442277 --- /dev/null +++ b/Documentation/media/v4l-drivers/imx7.rst @@ -0,0 +1,157 @@ +i.MX7 Video Capture Driver +========================== + +Introduction +------------ + +The i.MX7 contrary to the i.MX5/6 family does not contain an Image Processing +Unit (IPU), because of that the capabilities to perform operations or +manipulation of the capture frames is less feature rich. + +For image capture the i.MX7 have three units: +- CMOS Sensor Interface (CSI) +- Video Multiplexer +- MIPI CSI-2 Receiver + +:: + |\ + MIPI Camera Input ---> MIPI CSI-2 --- > | \ + | \ + | M | + | U | ------> CSI ---> Capture + | X | + | / + Parallel Camera Input ----------------> | / + |/ + +For additional information, please refer to the latest versions of the i.MX7 +reference manual [#f1]_. + +Entities +-------- + +imx7-mipi-csi2 +-------------- + +This is the MIPI CSI-2 recevier entity. It has one sink pad to receive the pixel +data from MIPI CSI-2 camera sensor. It has one source pad, corresponding to the +virtual channel 0. This module is compliant to previous version of Samsung +D-phy, and support two D-PHY Rx Data lanes. + +csi_mux +------- + +This is the video multiplexer. It has two sink pads to select from either camera +sensors with a parallel interface or from MIPI CSI-2 virtual channel 0. It has +a single source pad that routes to the CSI. + +csi +--- + +The CSI enables the chip to connect directly to external CMOS image sensor. CSI +can interfaces directly with Parallel and MIPI CSI-2 buses. It has 256 x 64 FIFO +to store received image pixel data and embedded DMA controllers to transfer data +from the FIFO through AHB bus. + +This entity has one sink pad that receive from the csi_mux entity and a single +source pad that route video frames directly to memory buffers, this pad is +routed to a capture device node. + +Usage Notes +----------- + +To aid in configuration and for backward compatibility with V4L2 applications +that access controls only from video device nodes, the capture device interfaces +inherit controls from the active entities in the current pipeline, so controls +can be accessed either directly from the subdev or from the active capture +device interface. For example, the sensor controls are available either from the +sensor subdevs or from the active capture device. + +Warp7 with OV2680 +----------------- + +On this platform an OV2680 MIPI CSI-2 module is connected to the internal MIPI +CSI-2 receiver. The following example configures a video capture pipeline with +an output of 800x600, and BGGR 10 bit bayer format: + +.. code-block:: none + # Setup links + media-ctl -l "'ov2680 1-0036':0 -> 'imx7-mipi-csis.0':0[1]" + media-ctl -l "'imx7-mipi-csis.0':1 -> 'csi_mux':1[1]" + media-ctl -l "'csi_mux':2 -> 'csi':0[1]" + media-ctl -l "'csi':1 -> 'csi capture':0[1]" + + # Configure pads for pipeline + media-ctl -V "'ov2680 1-0036':0 [fmt:SBGGR10_1X10/800x600 field:none]" + media-ctl -V "'csi_mux':1 [fmt:SBGGR10_1X10/800x600 field:none]" + media-ctl -V "'csi_mux':2 [fmt:SBGGR10_1X10/800x600 field:none]" + media-ctl -V "'imx7-mipi-csis.0':0 [fmt:SBGGR10_1X10/800x600 field:none]" + media-ctl -V "'csi':0 [fmt:SBGGR10_1X10/800x600 field:none]" + +After this streaming can start, the v4l2-ctl tool can be used to select any of +the resolutions supported by the sensor. + +.. code-block:: none + root@imx7s-warp:~# media-ctl -p + Media controller API version 4.17.0 + + Media device information + ------------------------ + driver imx-media + model imx-media + serial + bus info + hw revision 0x0 + driver version 4.17.0 + + Device topology + - entity 1: csi (2 pads, 2 links) + type V4L2 subdev subtype Unknown flags 0 + device node name /dev/v4l-subdev0 + pad0: Sink + [fmt:SBGGR10_1X10/800x600 field:none] + <- "csi_mux":2 [ENABLED] + pad1: Source + [fmt:SBGGR10_1X10/800x600 field:none] + -> "csi capture":0 [ENABLED] + + - entity 4: csi capture (1 pad, 1 link) + type Node subtype V4L flags 0 + device node name /dev/video0 + pad0: Sink + <- "csi":1 [ENABLED] + + - entity 10: csi_mux (3 pads, 2 links) + type V4L2 subdev subtype Unknown flags 0 + device node name /dev/v4l-subdev1 + pad0: Sink + [fmt:unknown/0x0] + pad1: Sink + [fmt:unknown/800x600 field:none] + <- "imx7-mipi-csis.0":1 [ENABLED] + pad2: Source + [fmt:unknown/800x600 field:none] + -> "csi":0 [ENABLED] + + - entity 14: imx7-mipi-csis.0 (2 pads, 2 links) + type V4L2 subdev subtype Unknown flags 0 + device node name /dev/v4l-subdev2 + pad0: Sink + [fmt:SBGGR10_1X10/800x600 field:none] + <- "ov2680 1-0036":0 [ENABLED] + pad1: Source + [fmt:SBGGR10_1X10/800x600 field:none] + -> "csi_mux":1 [ENABLED] + + - entity 17: ov2680 1-0036 (1 pad, 1 link) + type V4L2 subdev subtype Sensor flags 0 + device node name /dev/v4l-subdev3 + pad0: Source + [fmt:SBGGR10_1X10/800x600 field:none] + -> "imx7-mipi-csis.0":0 [ENABLED] + + +References +---------- + +.. [#f1] https://www.nxp.com/docs/en/reference-manual/IMX7SRM.pdf diff --git a/Documentation/media/v4l-drivers/index.rst b/Documentation/media/v4l-drivers/index.rst index 679238e786a7..693295bbc53f 100644 --- a/Documentation/media/v4l-drivers/index.rst +++ b/Documentation/media/v4l-drivers/index.rst @@ -44,6 +44,7 @@ For more details see the file COPYING in the source distribution of Linux. davinci-vpbe fimc imx + imx7 ivtv max2175 meye
Add rst document to describe the i.MX7 media driver and also a working example from the Warp7 board usage with a OV2680 sensor. Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> --- Documentation/media/v4l-drivers/imx7.rst | 157 ++++++++++++++++++++++ Documentation/media/v4l-drivers/index.rst | 1 + 2 files changed, 158 insertions(+) create mode 100644 Documentation/media/v4l-drivers/imx7.rst