| Message ID | 20200717132859.237120-12-jacopo+renesas@jmondi.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | dt-bindings: media: ov5640: Convert to json-schema | expand |
Hi Jacopo, Thank you for the patch. On Fri, Jul 17, 2020 at 03:28:57PM +0200, Jacopo Mondi wrote: > With the bindings now updated to initialize the DVP synchronism s/synchronism/synchronization/ > signals to the values reported by the datasheet, update the driver > to respect the same default values. > > The driver works-around a documentation bug and reports the VSYNC > polarity control bit to be inverted. Regardless of the actual > value written to the hardware register, initialize the DVP configuration > to the defaults reported by the chip manual and the bindings document: > > - VSYNC: active low > - HREF: active low > - PCLK: active high > > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > --- > drivers/media/i2c/ov5640.c | 16 ++++++++-------- > 1 file changed, 8 insertions(+), 8 deletions(-) > > diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c > index 2fe4a7ac0592..012ef1df59aa 100644 > --- a/drivers/media/i2c/ov5640.c > +++ b/drivers/media/i2c/ov5640.c > @@ -1212,9 +1212,9 @@ static int ov5640_set_stream_dvp(struct ov5640_dev *sensor, bool on) > { > int ret; > unsigned int flags = sensor->ep.bus.parallel.flags; > - u8 pclk_pol = 0; > + u8 pclk_pol = 1; > u8 hsync_pol = 0; > - u8 vsync_pol = 0; > + u8 vsync_pol = 1; > > /* > * Note about parallel port configuration. > @@ -1229,9 +1229,9 @@ static int ov5640_set_stream_dvp(struct ov5640_dev *sensor, bool on) > * devicetree endpoint control lines properties. > * If no endpoint control lines properties are set, > * polarity will be as below: > - * - VSYNC: active high > + * - VSYNC: active low > * - HREF: active low > - * - PCLK: active low > + * - PCLK: active high This changes the existing behaviour, doesn't it break DT backward compatibility ? > */ > > if (on) { > @@ -1245,12 +1245,12 @@ static int ov5640_set_stream_dvp(struct ov5640_dev *sensor, bool on) > * datasheet and hardware, 0 is active high > * and 1 is active low...) > */ > - if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING) > - pclk_pol = 1; > + if (flags & V4L2_MBUS_PCLK_SAMPLE_FALLING) > + pclk_pol = 0; > if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH) > hsync_pol = 1; > - if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW) > - vsync_pol = 1; > + if (flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH) > + vsync_pol = 0; > > ret = ov5640_write_reg(sensor, > OV5640_REG_POLARITY_CTRL00,
diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c index 2fe4a7ac0592..012ef1df59aa 100644 --- a/drivers/media/i2c/ov5640.c +++ b/drivers/media/i2c/ov5640.c @@ -1212,9 +1212,9 @@ static int ov5640_set_stream_dvp(struct ov5640_dev *sensor, bool on) { int ret; unsigned int flags = sensor->ep.bus.parallel.flags; - u8 pclk_pol = 0; + u8 pclk_pol = 1; u8 hsync_pol = 0; - u8 vsync_pol = 0; + u8 vsync_pol = 1; /* * Note about parallel port configuration. @@ -1229,9 +1229,9 @@ static int ov5640_set_stream_dvp(struct ov5640_dev *sensor, bool on) * devicetree endpoint control lines properties. * If no endpoint control lines properties are set, * polarity will be as below: - * - VSYNC: active high + * - VSYNC: active low * - HREF: active low - * - PCLK: active low + * - PCLK: active high */ if (on) { @@ -1245,12 +1245,12 @@ static int ov5640_set_stream_dvp(struct ov5640_dev *sensor, bool on) * datasheet and hardware, 0 is active high * and 1 is active low...) */ - if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING) - pclk_pol = 1; + if (flags & V4L2_MBUS_PCLK_SAMPLE_FALLING) + pclk_pol = 0; if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH) hsync_pol = 1; - if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW) - vsync_pol = 1; + if (flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH) + vsync_pol = 0; ret = ov5640_write_reg(sensor, OV5640_REG_POLARITY_CTRL00,
With the bindings now updated to initialize the DVP synchronism signals to the values reported by the datasheet, update the driver to respect the same default values. The driver works-around a documentation bug and reports the VSYNC polarity control bit to be inverted. Regardless of the actual value written to the hardware register, initialize the DVP configuration to the defaults reported by the chip manual and the bindings document: - VSYNC: active low - HREF: active low - PCLK: active high Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> --- drivers/media/i2c/ov5640.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-)