deleted file mode 100644
@@ -1,46 +0,0 @@
-* Omnivision OV2680 MIPI CSI-2 sensor
-
-Required Properties:
-- compatible: should be "ovti,ov2680".
-- clocks: reference to the xvclk input clock.
-- clock-names: should be "xvclk".
-- DOVDD-supply: Digital I/O voltage supply.
-- DVDD-supply: Digital core voltage supply.
-- AVDD-supply: Analog voltage supply.
-
-Optional Properties:
-- reset-gpios: reference to the GPIO connected to the powerdown/reset pin,
- if any. This is an active low signal to the OV2680.
-
-The device node must contain one 'port' child node for its digital output
-video port, and this port must have a single endpoint in accordance with
- the video interface bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-Endpoint node required properties for CSI-2 connection are:
-- remote-endpoint: a phandle to the bus receiver's endpoint node.
-- clock-lanes: should be set to <0> (clock lane on hardware lane 0).
-- data-lanes: should be set to <1> (one CSI-2 lane supported).
-
-Example:
-
-&i2c2 {
- ov2680: camera-sensor@36 {
- compatible = "ovti,ov2680";
- reg = <0x36>;
- clocks = <&osc>;
- clock-names = "xvclk";
- reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
- DOVDD-supply = <&sw2_reg>;
- DVDD-supply = <&sw2_reg>;
- AVDD-supply = <®_peri_3p15v>;
-
- port {
- ov2680_to_mipi: endpoint {
- remote-endpoint = <&mipi_from_sensor>;
- clock-lanes = <0>;
- data-lanes = <1>;
- };
- };
- };
-};
new file mode 100644
@@ -0,0 +1,101 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov2680.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV2680 CMOS Sensor
+
+maintainers:
+ - Rui Miguel Silva <rmfrfs@gmail.com>
+
+description: |-
+ The OV2680 color sensor is a low voltage, high performance 1/5 inch UXGA (2
+ megapixel) CMOS image sensor that provides a single-chip UXGA (1600 x 1200)
+ camera. It provides full-frame, sub-sampled, or windowed 10-bit images in
+ various formats via the control of the Serial Camera Control Bus (SCCB)
+ interface. The OV2680 has an image array capable of operating at up to 30
+ frames per second (fps) in UXGA resolution.
+
+properties:
+ compatible:
+ const: ovti,ov2680
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ description:
+ Input clock for the sensor.
+ items:
+ - const: xvclk
+
+ reset-gpios:
+ description:
+ The phandle and specifier for the GPIO that controls sensor reset.
+ This corresponds to the hardware pin XSHUTDOWN which is physically
+ active low.
+
+ dovdd-supply:
+ description:
+ Definition of the regulator used as interface power supply.
+
+ avdd-supply:
+ description:
+ Definition of the regulator used as analog power supply.
+
+ dvdd-supply:
+ description:
+ Definition of the regulator used as digital power supply.
+
+ port:
+ type: object
+ description:
+ A node containing an output port node with an endpoint definition
+ as documented in
+ Documentation/devicetree/bindings/media/video-interfaces.txt
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - dovdd-supply
+ - avdd-supply
+ - dvdd-supply
+ - reset-gpios
+ - port
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ov2680: camera-sensor@36 {
+ compatible = "ovti,ov2680";
+ reg = <0x36>;
+ clocks = <&osc>;
+ clock-names = "xvclk";
+ reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+
+ dovdd-supply = <&sw2_reg>;
+ dvdd-supply = <&sw2_reg>;
+ avdd-supply = <®_peri_3p15v>;
+
+ port {
+ ov2680_to_mipi: endpoint {
+ remote-endpoint = <&mipi_from_sensor>;
+ };
+ };
+ };
+ };
+
+...
@@ -12781,7 +12781,7 @@ M: Rui Miguel Silva <rmfrfs@gmail.com>
L: linux-media@vger.kernel.org
S: Maintained
T: git git://linuxtv.org/media_tree.git
-F: Documentation/devicetree/bindings/media/i2c/ov2680.txt
+F: Documentation/devicetree/bindings/media/i2c/ov2680.yaml
F: drivers/media/i2c/ov2680.c
OMNIVISION OV2685 SENSOR DRIVER