| Message ID | 20210319164148.199192-20-jacopo+renesas@jmondi.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | media: gmsl: Reliability improvement | expand |
Hi Jacopo, Thank you for the patch. On Fri, Mar 19, 2021 at 05:41:48PM +0100, Jacopo Mondi wrote: > The OV10635 image sensor embedded in the camera module is currently > reset after the MAX9271 initialization with two long delays that were > most probably not correctly characterized. > > Re-work the image sensor reset procedure by holding the chip in reset > during the MAX9271 configuration, removing the long sleep delays and > only wait after the chip exits from reset for 350-500 microseconds > interval, which is larger than the minimum (2048 * (1 / XVCLK)) timeout > characterized in the chip manual. > > Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> > Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > --- > drivers/media/i2c/rdacm20.c | 29 +++++++++++++++++------------ > 1 file changed, 17 insertions(+), 12 deletions(-) > > diff --git a/drivers/media/i2c/rdacm20.c b/drivers/media/i2c/rdacm20.c > index 7ed3866b5335..7ba2d0249da8 100644 > --- a/drivers/media/i2c/rdacm20.c > +++ b/drivers/media/i2c/rdacm20.c > @@ -454,6 +454,19 @@ static int rdacm20_init(struct v4l2_subdev *sd, unsigned int val) > if (ret) > return ret; > > + /* > + * Hold OV10635 in reset during max9271 configuration. The reset signal > + * has to be asserted for at least 200 microseconds. > + */ > + ret = max9271_enable_gpios(&dev->serializer, MAX9271_GPIO1OUT); > + if (ret) > + return ret; > + > + ret = max9271_clear_gpios(&dev->serializer, MAX9271_GPIO1OUT); enable and clear is very cnonfusing. How about mimicking the GPIO API, with direction_input(), direction_output() and set_value() functions ? It would also be nice if the polarity could be handled in a nicer way. There's no GPIO request API here, but maybe a max9271_gpio_set_flags() ? > + if (ret) > + return ret; > + usleep_range(200, 500); > + > ret = max9271_configure_gmsl_link(&dev->serializer); > if (ret) > return ret; > @@ -468,22 +481,14 @@ static int rdacm20_init(struct v4l2_subdev *sd, unsigned int val) > dev->serializer.client->addr = dev->addrs[0]; > > /* > - * Reset the sensor by cycling the OV10635 reset signal connected to the > - * MAX9271 GPIO1 and verify communication with the OV10635. > + * Release ov10635 from reset and initialize it. The image sensor > + * requires at least 2048 XVCLK cycles (85 micro-seconds at 24MHz) > + * before being available. Stay safe and wait up to 500 micro-seconds. > */ > - ret = max9271_enable_gpios(&dev->serializer, MAX9271_GPIO1OUT); > - if (ret) > - return ret; > - > - ret = max9271_clear_gpios(&dev->serializer, MAX9271_GPIO1OUT); > - if (ret) > - return ret; > - usleep_range(10000, 15000); > - > ret = max9271_set_gpios(&dev->serializer, MAX9271_GPIO1OUT); > if (ret) > return ret; > - usleep_range(10000, 15000); > + usleep_range(100, 500); > > for (i = 0; i < OV10635_PID_TIMEOUT; ++i) { > ret = ov10635_read16(dev, OV10635_PID);
Hi Laurent, On Sat, Mar 20, 2021 at 06:24:09PM +0200, Laurent Pinchart wrote: > Hi Jacopo, > > Thank you for the patch. > > On Fri, Mar 19, 2021 at 05:41:48PM +0100, Jacopo Mondi wrote: > > The OV10635 image sensor embedded in the camera module is currently > > reset after the MAX9271 initialization with two long delays that were > > most probably not correctly characterized. > > > > Re-work the image sensor reset procedure by holding the chip in reset > > during the MAX9271 configuration, removing the long sleep delays and > > only wait after the chip exits from reset for 350-500 microseconds > > interval, which is larger than the minimum (2048 * (1 / XVCLK)) timeout > > characterized in the chip manual. > > > > Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> > > Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > > --- > > drivers/media/i2c/rdacm20.c | 29 +++++++++++++++++------------ > > 1 file changed, 17 insertions(+), 12 deletions(-) > > > > diff --git a/drivers/media/i2c/rdacm20.c b/drivers/media/i2c/rdacm20.c > > index 7ed3866b5335..7ba2d0249da8 100644 > > --- a/drivers/media/i2c/rdacm20.c > > +++ b/drivers/media/i2c/rdacm20.c > > @@ -454,6 +454,19 @@ static int rdacm20_init(struct v4l2_subdev *sd, unsigned int val) > > if (ret) > > return ret; > > > > + /* > > + * Hold OV10635 in reset during max9271 configuration. The reset signal > > + * has to be asserted for at least 200 microseconds. > > + */ > > + ret = max9271_enable_gpios(&dev->serializer, MAX9271_GPIO1OUT); > > + if (ret) > > + return ret; > > + > > + ret = max9271_clear_gpios(&dev->serializer, MAX9271_GPIO1OUT); > > enable and clear is very cnonfusing. How about mimicking the GPIO API, > with direction_input(), direction_output() and set_value() functions ? > It would also be nice if the polarity could be handled in a nicer way. > There's no GPIO request API here, but maybe a max9271_gpio_set_flags() ? > Probably, that's an unrelated rework that could go on top unrelated to this patch > > + if (ret) > > + return ret; > > + usleep_range(200, 500); > > + > > ret = max9271_configure_gmsl_link(&dev->serializer); > > if (ret) > > return ret; > > @@ -468,22 +481,14 @@ static int rdacm20_init(struct v4l2_subdev *sd, unsigned int val) > > dev->serializer.client->addr = dev->addrs[0]; > > > > /* > > - * Reset the sensor by cycling the OV10635 reset signal connected to the > > - * MAX9271 GPIO1 and verify communication with the OV10635. > > + * Release ov10635 from reset and initialize it. The image sensor > > + * requires at least 2048 XVCLK cycles (85 micro-seconds at 24MHz) > > + * before being available. Stay safe and wait up to 500 micro-seconds. > > */ > > - ret = max9271_enable_gpios(&dev->serializer, MAX9271_GPIO1OUT); > > - if (ret) > > - return ret; > > - > > - ret = max9271_clear_gpios(&dev->serializer, MAX9271_GPIO1OUT); > > - if (ret) > > - return ret; > > - usleep_range(10000, 15000); > > - > > ret = max9271_set_gpios(&dev->serializer, MAX9271_GPIO1OUT); > > if (ret) > > return ret; > > - usleep_range(10000, 15000); > > + usleep_range(100, 500); > > > > for (i = 0; i < OV10635_PID_TIMEOUT; ++i) { > > ret = ov10635_read16(dev, OV10635_PID); > > -- > Regards, > > Laurent Pinchart
diff --git a/drivers/media/i2c/rdacm20.c b/drivers/media/i2c/rdacm20.c index 7ed3866b5335..7ba2d0249da8 100644 --- a/drivers/media/i2c/rdacm20.c +++ b/drivers/media/i2c/rdacm20.c @@ -454,6 +454,19 @@ static int rdacm20_init(struct v4l2_subdev *sd, unsigned int val) if (ret) return ret; + /* + * Hold OV10635 in reset during max9271 configuration. The reset signal + * has to be asserted for at least 200 microseconds. + */ + ret = max9271_enable_gpios(&dev->serializer, MAX9271_GPIO1OUT); + if (ret) + return ret; + + ret = max9271_clear_gpios(&dev->serializer, MAX9271_GPIO1OUT); + if (ret) + return ret; + usleep_range(200, 500); + ret = max9271_configure_gmsl_link(&dev->serializer); if (ret) return ret; @@ -468,22 +481,14 @@ static int rdacm20_init(struct v4l2_subdev *sd, unsigned int val) dev->serializer.client->addr = dev->addrs[0]; /* - * Reset the sensor by cycling the OV10635 reset signal connected to the - * MAX9271 GPIO1 and verify communication with the OV10635. + * Release ov10635 from reset and initialize it. The image sensor + * requires at least 2048 XVCLK cycles (85 micro-seconds at 24MHz) + * before being available. Stay safe and wait up to 500 micro-seconds. */ - ret = max9271_enable_gpios(&dev->serializer, MAX9271_GPIO1OUT); - if (ret) - return ret; - - ret = max9271_clear_gpios(&dev->serializer, MAX9271_GPIO1OUT); - if (ret) - return ret; - usleep_range(10000, 15000); - ret = max9271_set_gpios(&dev->serializer, MAX9271_GPIO1OUT); if (ret) return ret; - usleep_range(10000, 15000); + usleep_range(100, 500); for (i = 0; i < OV10635_PID_TIMEOUT; ++i) { ret = ov10635_read16(dev, OV10635_PID);