@@ -154,7 +154,8 @@ struct edid_state {
cta.has_vic_1 = cta.first_svd_might_be_preferred = cta.has_sldb =
cta.has_hdmi = cta.has_vcdb = cta.has_vfpdb = false;
cta.last_block_was_hdmi_vsdb = cta.have_hf_vsdb = cta.have_hf_scdb = false;
- cta.first_block = cta.first_svd = true;
+ cta.block_number = 0;
+ cta.first_svd = true;
cta.supported_hdmi_vic_codes = cta.supported_hdmi_vic_vsb_codes = 0;
memset(cta.vics, 0, sizeof(cta.vics));
memset(cta.preparsed_has_vic, 0, sizeof(cta.preparsed_has_vic));
@@ -259,7 +260,7 @@ struct edid_state {
unsigned short preparsed_phys_addr;
bool last_block_was_hdmi_vsdb;
bool have_hf_vsdb, have_hf_scdb;
- bool first_block;
+ unsigned block_number;
bool first_svd;
unsigned supported_hdmi_vic_codes;
unsigned supported_hdmi_vic_vsb_codes;
@@ -2131,7 +2131,7 @@ void edid_state::cta_block(const unsigned char *x, bool duplicate)
if (oui == 0x000c03) {
cta_hdmi_block(x, length);
cta.last_block_was_hdmi_vsdb = 1;
- cta.first_block = 0;
+ cta.block_number++;
// The HDMI OUI is present, so this EDID represents an HDMI
// interface. And HDMI interfaces must use EDID version 1.3
// according to the HDMI Specification, so check for this.
@@ -2194,7 +2194,7 @@ void edid_state::cta_block(const unsigned char *x, bool duplicate)
case 0x778:
cta_hf_eeodb(x, length);
// This must be the first CTA-861 block
- if (!cta.first_block)
+ if (cta.block_number > 0)
fail("Block starts at a wrong offset.\n");
break;
case 0x779:
@@ -2216,7 +2216,7 @@ void edid_state::cta_block(const unsigned char *x, bool duplicate)
hex_block(" ", x, length);
}
- cta.first_block = 0;
+ cta.block_number++;
cta.last_block_was_hdmi_vsdb = 0;
}
@@ -2333,11 +2333,11 @@ void edid_state::parse_cta_block(const unsigned char *x)
// msg(!cta.has_hdmi, "If YCbCr support is indicated, then both 4:2:2 and 4:4:4 %s be supported.\n",
// cta.has_hdmi ? "shall" : "should");
printf(" Native detailed modes: %u\n", x[3] & 0x0f);
- if (cta.first_block)
+ if (cta.block_number == 0)
cta.byte3 = x[3];
else if (x[3] != cta.byte3)
fail("Byte 3 must be the same for all CTA-861 Extension Blocks.\n");
- if (cta.first_block) {
+ if (cta.block_number == 0) {
unsigned native_dtds = x[3] & 0x0f;
cta.native_timings.clear();
track progress instead of milestones. With a flag like first_block, you can only know if you're at the first block or not. But with a progressing value like block_number, you can know when you're at the first block or second block etc. and you can know how many blocks have been done. We'll also replace last_block_was_hdmi_vsdb in a later commit. Both of these changes will cleanup the hdmi block. Signed-off-by: Joe van Tunen <joevt@shaw.ca> --- edid-decode.h | 5 +++-- parse-cta-block.cpp | 10 +++++----- 2 files changed, 8 insertions(+), 7 deletions(-)