@@ -37,6 +37,8 @@
#define V4L2_CID_ASPEED_HQ_MODE (ASPEED_CID_CUSTOM_BASE + 3)
#define V4L2_CID_ASPEED_HQ_JPEG_QUALITY (ASPEED_CID_CUSTOM_BASE + 4)
+#define ASPEED_VIDEO_V4L2_MIN_BUF_REQ 3
+
#define LOG_REG BIT(4)
#define LOG_DEBUG BIT(3)
#define LOG_TRACE BIT(2)
@@ -213,6 +215,15 @@
#define VE_MEM_RESTRICT_START 0x310
#define VE_MEM_RESTRICT_END 0x314
+/*
+ * @VIDEO_MODE_DETECT_DONE: a flag raised if signal lock
+ * @VIDEO_RES_CHANGE: a flag raised if res_change work on-going
+ * @VIDEO_RES_DETECT: a flag raised if res. detection on-going
+ * @VIDEO_STREAMING: a flag raised if user requires stream-on
+ * @VIDEO_FRAME_INPRG: a flag raised if hw working on a frame
+ * @VIDEO_STOPPED: a flag raised if device release
+ * @VIDEO_CLOCKS_ON: a flag raised if clk is on
+ */
enum {
VIDEO_MODE_DETECT_DONE,
VIDEO_RES_CHANGE,
@@ -245,6 +256,28 @@ struct aspeed_video_perf {
#define to_aspeed_video_buffer(x) \
container_of((x), struct aspeed_video_buffer, vb)
+/**
+ * struct aspeed_video - driver data
+ *
+ * @flags: holds the state of video
+ * @sequence: holds the last number of frame completed
+ * @max_compressed_size:holds max compressed stream's size
+ * @srcs: holds the buffer information for srcs
+ * @jpeg: holds the buffer information for jpeg header
+ * @bcd: holds the buffer information for bcd work
+ * @yuv420: a flag raised if JPEG subsampling is 420
+ * @partial_jpeg: a flag raised if JPEG supports partial capture
+ * @hq_mode: a flag raised if HQ is enabled. Only for partial_jpeg
+ * @frame_rate: holds the frame_rate
+ * @jpeg_quality: holds jpeq's quality (0~11)
+ * @jpeg_hq_quality: holds hq's quality (0~11) only if hq_mode enabled
+ * @compression_mode: holds jpeg compression mode
+ * @frame_bottom: end position of video data in vertical direction
+ * @frame_left: start position of video data in horizontal direction
+ * @frame_right: end position of video data in horizontal direction
+ * @frame_top: start position of video data in vertical direction
+ * @perf: holds the statistics primary for debugfs
+ */
struct aspeed_video {
void __iomem *base;
struct clk *eclk;
@@ -1250,7 +1283,7 @@ static int aspeed_video_get_parm(struct file *file, void *fh,
struct aspeed_video *video = video_drvdata(file);
a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
- a->parm.capture.readbuffers = 3;
+ a->parm.capture.readbuffers = ASPEED_VIDEO_V4L2_MIN_BUF_REQ;
a->parm.capture.timeperframe.numerator = 1;
if (!video->frame_rate)
a->parm.capture.timeperframe.denominator = MAX_FRAME_RATE;
@@ -1267,7 +1300,7 @@ static int aspeed_video_set_parm(struct file *file, void *fh,
struct aspeed_video *video = video_drvdata(file);
a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
- a->parm.capture.readbuffers = 3;
+ a->parm.capture.readbuffers = ASPEED_VIDEO_V4L2_MIN_BUF_REQ;
if (a->parm.capture.timeperframe.numerator)
frame_rate = a->parm.capture.timeperframe.denominator /
@@ -1876,7 +1909,7 @@ static int aspeed_video_setup_video(struct aspeed_video *video)
vbq->drv_priv = video;
vbq->buf_struct_size = sizeof(struct aspeed_video_buffer);
vbq->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
- vbq->min_buffers_needed = 3;
+ vbq->min_buffers_needed = ASPEED_VIDEO_V4L2_MIN_BUF_REQ;
rc = vb2_queue_init(vbq);
if (rc) {
Add comments to describe video-stat and 'struct aspeed_video'. Add macro, ASPEED_VIDEO_V4L2_MIN_BUF_REQ, to describe the buffers needed. Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com> --- drivers/media/platform/aspeed-video.c | 39 ++++++++++++++++++++++++--- 1 file changed, 36 insertions(+), 3 deletions(-)