@@ -134,10 +134,19 @@ static inline struct ov7251 *to_ov7251(struct v4l2_subdev *sd)
}
enum xclk_rate {
+ OV7251_19_2_MHZ,
OV7251_24_MHZ,
OV7251_NUM_SUPPORTED_RATES
};
+static const struct ov7251_pll1_config ov7251_pll1_config_19_2_mhz = {
+ .pre_div = 0x03,
+ .mult = 0x4b,
+ .div = 0x01,
+ .pix_div = 0x0a,
+ .mipi_div = 0x05
+};
+
static const struct ov7251_pll1_config ov7251_pll1_config_24_mhz = {
.pre_div = 0x03,
.mult = 0x64,
@@ -146,6 +155,14 @@ static const struct ov7251_pll1_config ov7251_pll1_config_24_mhz = {
.mipi_div = 0x05
};
+static const struct ov7251_pll2_config ov7251_pll2_config_19_2_mhz = {
+ .pre_div = 0x04,
+ .mult = 0x32,
+ .div = 0x00,
+ .sys_div = 0x05,
+ .adc_div = 0x04
+};
+
static const struct ov7251_pll2_config ov7251_pll2_config_24_mhz = {
.pre_div = 0x04,
.mult = 0x28,
@@ -154,12 +171,18 @@ static const struct ov7251_pll2_config ov7251_pll2_config_24_mhz = {
.adc_div = 0x04
};
+static const struct ov7251_pll_configs ov7251_pll_configs_19_2_mhz = {
+ .pll1 = &ov7251_pll1_config_19_2_mhz,
+ .pll2 = &ov7251_pll2_config_19_2_mhz
+};
+
static const struct ov7251_pll_configs ov7251_pll_configs_24_mhz = {
.pll1 = &ov7251_pll1_config_24_mhz,
.pll2 = &ov7251_pll2_config_24_mhz
};
static const struct ov7251_pll_configs *ov7251_pll_configs[] = {
+ [OV7251_19_2_MHZ] = &ov7251_pll_configs_19_2_mhz,
[OV7251_24_MHZ] = &ov7251_pll_configs_24_mhz
};
@@ -553,6 +576,7 @@ static const struct reg_value ov7251_setting_vga_90fps[] = {
};
static const unsigned long supported_xclk_rates[] = {
+ [OV7251_19_2_MHZ] = 19200000,
[OV7251_24_MHZ] = 24000000,
};
@@ -1423,6 +1447,7 @@ static int ov7251_probe(struct i2c_client *client)
struct device *dev = &client->dev;
struct ov7251 *ov7251;
u8 chip_id_high, chip_id_low, chip_rev;
+ unsigned int rate = 0;
int ret;
int i;
@@ -1438,35 +1463,39 @@ static int ov7251_probe(struct i2c_client *client)
return ret;
/* get system clock (xclk) */
- ov7251->xclk = devm_clk_get(dev, "xclk");
+ ov7251->xclk = devm_clk_get(dev, NULL);
if (IS_ERR(ov7251->xclk)) {
dev_err(dev, "could not get xclk");
return PTR_ERR(ov7251->xclk);
}
+ /*
+ * We could have either a 24MHz or 19.2MHz clock rate from either dt or
+ * ACPI. We also need to support the IPU3 case which will have both an
+ * external clock AND a clock-frequency property.
+ */
ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
- &ov7251->xclk_freq);
- if (ret) {
- dev_err(dev, "could not get xclk frequency\n");
- return ret;
+ &rate);
+ if (!ret && ov7251->xclk) {
+ ret = clk_set_rate(ov7251->xclk, rate);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "failed to set clock rate\n");
+ } else if (ret && !ov7251->xclk) {
+ return dev_err_probe(dev, ret, "invalid clock config\n");
}
- /* external clock must be 24MHz, allow 1% tolerance */
- if (ov7251->xclk_freq < 23760000 || ov7251->xclk_freq > 24240000) {
- dev_err(dev, "external clock frequency %u is not supported\n",
- ov7251->xclk_freq);
- return -EINVAL;
- }
+ ov7251->xclk_freq = rate ? rate : clk_get_rate(ov7251->xclk);
- ret = clk_set_rate(ov7251->xclk, ov7251->xclk_freq);
- if (ret) {
- dev_err(dev, "could not set xclk frequency\n");
- return ret;
- }
for (i = 0; i < ARRAY_SIZE(supported_xclk_rates); i++)
if (ov7251->xclk_freq == supported_xclk_rates[i])
break;
+ if (i == ARRAY_SIZE(supported_xclk_rates))
+ return dev_err_probe(dev, -EINVAL,
+ "clock rate %u Hz is unsupported\n",
+ ov7251->xclk_freq);
+
ov7251->pll_configs = ov7251_pll_configs[i];
ov7251->io_regulator = devm_regulator_get(dev, "vdddo");
The OV7251 sensor is used as the IR camera sensor on the Microsoft Surface line of tablets; this provides a 19.2MHz external clock. Add the ability to support that rate to the driver by defining a new set of PLL configs. Extend the clock handling in .probe() to check for either supported frequency. Signed-off-by: Daniel Scally <djrscally@gmail.com> --- drivers/media/i2c/ov7251.c | 61 ++++++++++++++++++++++++++++---------- 1 file changed, 45 insertions(+), 16 deletions(-)