@@ -13,6 +13,7 @@
#include <linux/mailbox_controller.h>
#include <linux/kfifo.h>
+#define VPU_TIMEOUT_WAKEUP msecs_to_jiffies(200)
#define VPU_TIMEOUT msecs_to_jiffies(1000)
#define VPU_INST_NULL_ID (-1L)
#define VPU_MSG_BUFFER_SIZE (8192)
@@ -269,7 +269,7 @@ static bool check_is_responsed(struct vpu_inst *inst, unsigned long key)
return flag;
}
-static int sync_session_response(struct vpu_inst *inst, unsigned long key)
+static int sync_session_response(struct vpu_inst *inst, unsigned long key, long timeout, int try)
{
struct vpu_core *core;
@@ -279,10 +279,12 @@ static int sync_session_response(struct vpu_inst *inst, unsigned long key)
core = inst->core;
call_void_vop(inst, wait_prepare);
- wait_event_timeout(core->ack_wq, check_is_responsed(inst, key), VPU_TIMEOUT);
+ wait_event_timeout(core->ack_wq, check_is_responsed(inst, key), timeout);
call_void_vop(inst, wait_finish);
if (!check_is_responsed(inst, key)) {
+ if (try)
+ return -EINVAL;
dev_err(inst->dev, "[%d] sync session timeout\n", inst->id);
set_bit(inst->id, &core->hang_mask);
mutex_lock(&inst->core->cmd_lock);
@@ -294,6 +296,19 @@ static int sync_session_response(struct vpu_inst *inst, unsigned long key)
return 0;
}
+static void vpu_core_keep_active(struct vpu_core *core)
+{
+ struct vpu_rpc_event pkt;
+
+ memset(&pkt, 0, sizeof(pkt));
+ vpu_iface_pack_cmd(core, &pkt, 0, VPU_CMD_ID_NOOP, NULL);
+
+ dev_dbg(core->dev, "try to wake up\n");
+ mutex_lock(&core->cmd_lock);
+ vpu_cmd_send(core, &pkt);
+ mutex_unlock(&core->cmd_lock);
+}
+
static int vpu_session_send_cmd(struct vpu_inst *inst, u32 id, void *data)
{
unsigned long key;
@@ -304,9 +319,25 @@ static int vpu_session_send_cmd(struct vpu_inst *inst, u32 id, void *data)
return -EINVAL;
ret = vpu_request_cmd(inst, id, data, &key, &sync);
- if (!ret && sync)
- ret = sync_session_response(inst, key);
+ if (ret)
+ goto exit;
+
+ /* workaround for a firmware issue,
+ * firmware should be waked up by start or configure command,
+ * but there is a very small change that firmware failed to wakeup.
+ * in such case, try to wakeup firmware again by sending a noop command
+ */
+ if (sync && (id == VPU_CMD_ID_CONFIGURE_CODEC || id == VPU_CMD_ID_START)) {
+ if (sync_session_response(inst, key, VPU_TIMEOUT_WAKEUP, 1))
+ vpu_core_keep_active(inst->core);
+ else
+ goto exit;
+ }
+
+ if (sync)
+ ret = sync_session_response(inst, key, VPU_TIMEOUT, 0);
+exit:
if (ret)
dev_err(inst->dev, "[%d] send cmd(0x%x) fail\n", inst->id, id);
@@ -693,6 +693,7 @@ int vpu_malone_set_decode_params(struct vpu_shared_addr *shared,
}
static struct vpu_pair malone_cmds[] = {
+ {VPU_CMD_ID_NOOP, VID_API_CMD_NULL},
{VPU_CMD_ID_START, VID_API_CMD_START},
{VPU_CMD_ID_STOP, VID_API_CMD_STOP},
{VPU_CMD_ID_ABORT, VID_API_CMD_ABORT},
@@ -658,6 +658,7 @@ int vpu_windsor_get_stream_buffer_size(struct vpu_shared_addr *shared)
}
static struct vpu_pair windsor_cmds[] = {
+ {VPU_CMD_ID_NOOP, GTB_ENC_CMD_NOOP},
{VPU_CMD_ID_CONFIGURE_CODEC, GTB_ENC_CMD_CONFIGURE_CODEC},
{VPU_CMD_ID_START, GTB_ENC_CMD_STREAM_START},
{VPU_CMD_ID_STOP, GTB_ENC_CMD_STREAM_STOP},
firmware should be waked up by start or configure command, but there is a very small chance that firmware failed to wakeup. in such case, try to wakeup firmware again by sending a noop command Fixes: 6de8d628df6e ("media: amphion: add v4l2 m2m vpu decoder stateful driver") Signed-off-by: Ming Qian <ming.qian@nxp.com> --- drivers/media/platform/amphion/vpu.h | 1 + drivers/media/platform/amphion/vpu_cmds.c | 39 ++++++++++++++++++-- drivers/media/platform/amphion/vpu_malone.c | 1 + drivers/media/platform/amphion/vpu_windsor.c | 1 + 4 files changed, 38 insertions(+), 4 deletions(-)