@@ -817,12 +817,13 @@ static int imx290_set_stream(struct v4l2_subdev *sd, int enable)
ret = imx290_start_streaming(imx290, state);
if (ret) {
dev_err(imx290->dev, "Start stream failed\n");
- pm_runtime_put(imx290->dev);
+ pm_runtime_put_sync(imx290->dev);
goto unlock;
}
} else {
imx290_stop_streaming(imx290);
- pm_runtime_put(imx290->dev);
+ pm_runtime_mark_last_busy(imx290->dev);
+ pm_runtime_put_autosuspend(imx290->dev);
}
unlock:
@@ -1250,18 +1251,16 @@ static int imx290_probe(struct i2c_client *client)
if (ret)
return ret;
- /* Initialize and register subdev. */
+ /* Initialize the V4L2 subdev. */
ret = imx290_subdev_init(imx290);
if (ret)
return ret;
- ret = v4l2_async_register_subdev(&imx290->sd);
- if (ret < 0) {
- dev_err(dev, "Could not register v4l2 device\n");
- goto err_subdev;
- }
-
- /* Power on the device to match runtime PM state below */
+ /*
+ * Enable power management. The driver supports runtime PM, but needs to
+ * work when runtime PM is disabled in the kernel. To that end, power
+ * the sensor on manually here, identify it, and fully initialize it.
+ */
ret = imx290_power_on(dev);
if (ret < 0) {
dev_err(dev, "Could not power on the device\n");
@@ -1271,21 +1270,45 @@ static int imx290_probe(struct i2c_client *client)
ret = imx290_read(imx290, IMX290_CHIP_ID, &chip_id);
if (ret) {
dev_err(dev, "Could not read chip ID: %d\n", ret);
- imx290_power_off(dev);
- goto err_subdev;
+ goto err_power;
}
dev_info(dev, "chip ID 0x%04x\n", chip_id);
+ /*
+ * Enable runtime PM. As the device has been powered manually, mark it
+ * as active, and increase the usage count without resuming the device.
+ */
pm_runtime_set_active(dev);
+ pm_runtime_get_noresume(dev);
pm_runtime_enable(dev);
- pm_runtime_idle(dev);
+
+ /* Register the V4L2 subdev. */
+ ret = v4l2_async_register_subdev(&imx290->sd);
+ if (ret < 0) {
+ dev_err(dev, "Could not register v4l2 device\n");
+ goto err_pm;
+ }
+
+ /*
+ * Finally, enable autosuspend and decrease the usage count. The device
+ * will get suspended after the autosuspend delay, turning the power
+ * off.
+ */
+ pm_runtime_set_autosuspend_delay(dev, 1000);
+ pm_runtime_use_autosuspend(dev);
+ pm_runtime_mark_last_busy(dev);
+ pm_runtime_put_autosuspend(dev);
return 0;
+err_pm:
+ pm_runtime_disable(dev);
+ pm_runtime_put_noidle(dev);
+err_power:
+ imx290_power_off(dev);
err_subdev:
imx290_subdev_cleanup(imx290);
-
return ret;
}
@@ -1297,6 +1320,10 @@ static void imx290_remove(struct i2c_client *client)
v4l2_async_unregister_subdev(sd);
imx290_subdev_cleanup(imx290);
+ /*
+ * Disable runtime PM. In case runtime PM is disabled in the kernel,
+ * make sure to turn power off manually.
+ */
pm_runtime_disable(imx290->dev);
if (!pm_runtime_status_suspended(imx290->dev))
imx290_power_off(imx290->dev);
Use runtime PM autosuspend to avoid powering off the sensor during fast stop-reconfigure-restart cycles. This also fixes runtime PM handling in the probe function that didn't suspend the device, effectively leaving it resumed forever. While at it, improve documentation of power management in probe() and remove(). Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> --- drivers/media/i2c/imx290.c | 55 ++++++++++++++++++++++++++++---------- 1 file changed, 41 insertions(+), 14 deletions(-)